[PATCH 2/4] arm64: dts: qcom: add sdm845-google-blueline (Pixel 3)

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Amit Pundir <amit.pundir@xxxxxxxxxx>

This adds an initial dts for the Blueline (Pixel 3). Supported
functionality includes display, Debug UART, UFS, USB-C (peripheral), WiFi,
Bluetooth and modem.

Bootloader compatible board and msm IDs are needed for the kernel to boot
with Pixel3 bootloader, so those are added.

GPIOs 0 through 3 and 81 through 84 are configured to not be accessible
from the application CPUs, so we mark them as reserved to allow the Pixel 3
to boot.

The reserved-memory locations where obtained from downstream using
kernel logs:
https://gist.github.com/calebccff/090d10bfac3cb9e9bd98dda30b054c96

The rmtfs region is allocated with UIO, making it technically "dynamic".
It's address and size can be read from sysfs:

blueline:/ # cat /sys/class/uio/uio0/name
rmtfs
at /sys/class/uio/uio0/maps/map0/addr
0x00000000f2701000
blueline:/ # cat /sys/class/uio/uio0/maps/map0/size
0x0000000000200000

Like the OnePlus 6, it needs 1kB reserved on either side of the rmtfs
memory to workaround some XPU bug which would otherwise cause erroneous
XPU violations when accessing the rmtfs_mem region.

For wifi, the pixel 3 reports a board-id of 0xFF, and downstream
only includes a single bdwlan file. The qcom,ath10k-calibration-variant
property is set to ensure that the correct calibration data is used.

Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
[AmitP: Cherry-picked and refactored from Bjorn's db845c dts
        ("arm64: dts: qcom: Add Dragonboard 845c") https://lkml.org/lkml/2019/6/6/7]
Signed-off-by: Amit Pundir <amit.pundir@xxxxxxxxxx>
[sumits: merged commits to add board and msm ids, gpio range reservation,
  ufs device-reset gpio and adaptation to v5.5+ changes]
Signed-off-by: Sumit Semwal <sumit.semwal@xxxxxxxxxx>
[vinod: Add display nodes]
Signed-off-by: Vinod Koul <vkoul@xxxxxxxxxx>
[caleb: remove db845c bits, cleanup, add reserved-memory for modem/wifi]
Signed-off-by: Caleb Connolly <caleb@xxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/sdm845-google-blueline.dts  | 652 ++++++++++++++++++
 2 files changed, 653 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 2f8aec2cc6db..c151e17e6eb7 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -100,6 +100,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-google-blueline.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-oneplus-enchilada.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-oneplus-fajita.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts b/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts
new file mode 100644
index 000000000000..dec979ad9209
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts
@@ -0,0 +1,652 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include <dt-bindings/dma/qcom-gpi.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/delete-node/ &mpss_region;
+/delete-node/ &venus_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &mba_region;
+/delete-node/ &slpi_mem;
+/delete-node/ &spss_mem;
+/delete-node/ &rmtfs_mem;
+
+/ {
+	model = "Google Pixel 3";
+	compatible = "google,blueline", "qcom,sdm845";
+	qcom,board-id = <0x00021505 0>;
+	qcom,msm-id = <321 0x20001>;
+
+	aliases {
+		serial0 = &uart9;
+		serial1 = &uart6;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	volume-keys {
+		compatible = "gpio-keys";
+		label = "Volume keys";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&volume_up_gpio>;
+
+		vol-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		mpss_region: memory@8e000000 {
+			reg = <0 0x8e000000 0 0x9800000>;
+			no-map;
+		};
+
+		venus_mem: venus@97800000 {
+			reg = <0 0x97800000 0 0x500000>;
+			no-map;
+		};
+
+		cdsp_mem: cdsp-mem@97D00000 {
+			reg = <0 0x97D00000 0 0x800000>;
+			no-map;
+		};
+
+		mba_region: mba@98500000 {
+			reg = <0 0x98500000 0 0x200000>;
+			no-map;
+		};
+
+		slpi_mem: slpi@98700000 {
+			reg = <0 0x98700000 0 0x1400000>;
+			no-map;
+		};
+
+		spss_mem: spss@99B00000 {
+			reg = <0 0x99B00000 0 0x100000>;
+			no-map;
+		};
+
+		/* rmtfs lower guard */
+		memory@f2700000 {
+			reg = <0 0xf2700000 0 0x1000>;
+			no-map;
+		};
+
+		rmtfs_mem: memory@f2701000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xf2701000 0 0x200000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
+
+		/* rmtfs upper guard */
+		memory@f2901000 {
+			reg = <0 0xf2901000 0 0x1000>;
+			no-map;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_s4a_1p8: vreg-s4a-1p8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&adsp_pas {
+	status = "okay";
+
+	firmware-name = "qcom/sdm845/pixel3/adsp.mbn";
+};
+
+&apps_rsc {
+	pm8998-rpmh-regulators {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+		vdd-s13-supply = <&vph_pwr>;
+		vdd-l1-l27-supply = <&vreg_s7a_1p025>;
+		vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+		vdd-l3-l11-supply = <&vreg_s7a_1p025>;
+		vdd-l4-l5-supply = <&vreg_s7a_1p025>;
+		vdd-l6-supply = <&vph_pwr>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+		vdd-l9-supply = <&vreg_bob>;
+		vdd-l10-l23-l25-supply = <&vreg_bob>;
+		vdd-l13-l19-l21-supply = <&vreg_bob>;
+		vdd-l16-l28-supply = <&vreg_bob>;
+		vdd-l18-l22-supply = <&vreg_bob>;
+		vdd-l20-l24-supply = <&vreg_bob>;
+		vdd-l26-supply = <&vreg_s3a_1p35>;
+		vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p35: smps3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s5a_2p04: smps5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: smps7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vdda_mipi_dsi0_pll:
+		vreg_l1a_0p875: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+		};
+
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a_2p95: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p88: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+			/*
+			 * We can't properly bring the panel back if it gets turned off
+			 * so keep it's regulators always on for now.
+			 */
+			regulator-always-on;
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l19a_3p3: ldo19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			qcom,init-voltage = <3300000>;
+			qcom,initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			/*
+			 * The touchscreen needs this to be 3.3v, which is apparently
+			 * quite close to the hardware limit for this LDO (3.312v)
+			 * It must be kept in high power mode to prevent TS brownouts
+			 */
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a_2p95: ldo20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a_2p95: ldo21 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l24a_3p075: ldo24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p3: ldo25 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_mipi_dsi0_1p2:
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+		};
+
+		vreg_l28a_3p0: ldo28 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+			/*
+			 * We can't properly bring the panel back if it gets turned off
+			 * so keep it's regulators always on for now.
+			 */
+			regulator-always-on;
+		};
+	};
+
+	pmi8998-rpmh-regulators {
+		compatible = "qcom,pmi8998-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+			regulator-allow-bypass;
+		};
+	};
+
+	pm8005-rpmh-regulators {
+		compatible = "qcom,pm8005-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s3c_0p6: smps3 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <600000>;
+		};
+	};
+};
+
+&cdsp_pas {
+	status = "okay";
+	firmware-name = "qcom/sdm845/pixel3/cdsp.mbn";
+};
+
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vdda_mipi_dsi0_1p2>;
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lg_sw43408_in_0>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+
+	panel@0 {
+		compatible = "lg,sw43408";
+		reg = <0>;
+
+		vddi-supply = <&vreg_l14a_1p88>;
+		vpnl-supply = <&vreg_l28a_3p0>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_pmgpio_pins>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				lg_sw43408_in_0: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	remote-endpoint = <&lg_sw43408_in_0>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vdda_mipi_dsi0_pll>;
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+			   <GCC_QSPI_CORE_CLK_SRC>,
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
+};
+
+&gmu {
+	status = "okay";
+};
+
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/sdm845/pixel3/a630_zap.mbn";
+	};
+};
+
+&ipa {
+	status = "okay";
+
+	firmware-name = "qcom/sdm845/pixel3/ipa_fws.mbn";
+};
+
+&mss_pil {
+	status = "okay";
+	firmware-name = "qcom/sdm845/pixel3/mba.mbn", "qcom/sdm845/pixel3/modem.mbn";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
+&pm8998_gpio {
+	volume_up_gpio: vol-up-active {
+		pins = "gpio6";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		qcom,drive-strength = <0>;
+	};
+
+	panel_pmgpio_pins: panel-pmgpio-active {
+		pins = "gpio2", "gpio5";
+		function = "normal";
+		input-enable;
+		bias-disable;
+		power-source = <0>;
+	};
+};
+
+&pm8998_pon {
+	resin {
+		compatible = "qcom,pm8941-resin";
+		interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+		debounce = <15625>;
+		bias-pull-up;
+		linux,code = <KEY_VOLUMEDOWN>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&qup_uart6_default {
+	pinmux {
+		pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		function = "qup6";
+	};
+
+	cts {
+		pins = "gpio45";
+		bias-disable;
+	};
+
+	rts-tx {
+		pins = "gpio46", "gpio47";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rx {
+		pins = "gpio48";
+		bias-pull-up;
+	};
+};
+
+&qup_uart9_default {
+	pinconf-tx {
+		pins = "gpio4";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pinconf-rx {
+		pins = "gpio5";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	panel_te_pin: panel-te {
+		mux {
+			pins = "gpio12";
+			function = "mdp_vsync";
+			drive-strength = <2>;
+			bias-disable;
+			input-enable;
+		};
+	};
+
+	panel_reset_pins: panel-active {
+		mux {
+			pins = "gpio6", "gpio52";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-disable = <0>;
+		};
+	};
+
+	panel_suspend: panel-suspend {
+		mux {
+			pins = "gpio6", "gpio52";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	touchscreen_reset: ts-reset {
+		mux {
+			pins = "gpio99";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+			//output-high;
+		};
+	};
+
+	touchscreen_pins: ts-pins {
+		mux {
+			pins = "gpio125";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	touchscreen_i2c_pins: qup-i2c2-gpio {
+		pins = "gpio27", "gpio28";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&uart6 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&uart9 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l26a_1p2>;
+	vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
+};
+
+&usb_2_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l26a_1p2>;
+	vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <800000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&venus {
+	status = "okay";
+	firmware-name = "qcom/sdm845/oneplus6/venus.mbn";
+};
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+
+	qcom,snoc-host-cap-8bit-quirk;
+	qcom,ath10k-calibration-variant = "google_blueline";
+};
-- 
2.36.1




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux