Reorganize node order and sort them by address. Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx> --- This was picked from for-next qcom branch [1]. Reorganize dtsi as requested. [1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next arch/arm/boot/dts/qcom-ipq8064.dtsi | 766 ++++++++++++++-------------- 1 file changed, 383 insertions(+), 383 deletions(-) diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi index da90f7c08d75..cf41d330c920 100644 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi @@ -332,19 +332,59 @@ soc: soc { ranges; compatible = "simple-bus"; - lpass@28100000 { - compatible = "qcom,lpass-cpu"; - status = "disabled"; - clocks = <&lcc AHBIX_CLK>, - <&lcc MI2S_OSR_CLK>, - <&lcc MI2S_BIT_CLK>; - clock-names = "ahbix-clk", - "mi2s-osr-clk", - "mi2s-bit-clk"; - interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; - interrupt-names = "lpass-irq-lpaif"; - reg = <0x28100000 0x10000>; - reg-names = "lpass-lpaif"; + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <7>; + snps,rd_osr_lmt = <7>; + snps,blen = <16 0 0 0 0 0 0>; + }; + + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + rpm: rpm@108000 { + compatible = "qcom,rpm-ipq8064"; + reg = <0x108000 0x1000>; + qcom,ipc = <&l2cc 0x8 2>; + + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ack", "err", "wakeup"; + + clocks = <&gcc RPM_MSG_RAM_H_CLK>; + clock-names = "ram"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; + #clock-cells = <1>; + }; + }; + + qcom,ssbi@500000 { + compatible = "qcom,ssbi"; + reg = <0x00500000 0x1000>; + qcom,controller-type = "pmic-arbiter"; + }; + + qfprom: qfprom@700000 { + compatible = "qcom,ipq8064-qfprom", "qcom,qfprom"; + reg = <0x00700000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + speedbin_efuse: speedbin@c0 { + reg = <0xc0 0x4>; + }; + tsens_calib: calib@400 { + reg = <0x400 0xb>; + }; + tsens_calib_backup: calib_backup@410 { + reg = <0x410 0xb>; + }; }; qcom_pinmux: pinmux@800000 { @@ -471,6 +511,35 @@ mux { }; }; + gcc: clock-controller@900000 { + compatible = "qcom,gcc-ipq8064", "syscon"; + clocks = <&pxo_board>, <&cxo_board>; + clock-names = "pxo", "cxo"; + reg = <0x00900000 0x4000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + + tsens: thermal-sensor@900000 { + compatible = "qcom,ipq8064-tsens"; + + nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; + nvmem-cell-names = "calib", "calib_backup"; + interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow"; + + #qcom,sensors = <11>; + #thermal-sensor-cells = <1>; + }; + }; + + sfpb_mutex: hwlock@1200600 { + compatible = "qcom,sfpb-mutex"; + reg = <0x01200600 0x100>; + + #hwlock-cells = <1>; + }; + intc: interrupt-controller@2000000 { compatible = "qcom,msm-qgic2"; interrupt-controller; @@ -500,46 +569,198 @@ IRQ_TYPE_EDGE_RISING)>, cpu-offset = <0x80000>; }; + l2cc: clock-controller@2011000 { + compatible = "qcom,kpss-gcc", "syscon"; + reg = <0x2011000 0x1000>; + clocks = <&gcc PLL8_VOTE>, <&pxo_board>; + clock-names = "pll8_vote", "pxo"; + clock-output-names = "acpu_l2_aux"; + }; + acc0: clock-controller@2088000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02088000 0x1000>, <0x02008000 0x1000>; }; + saw0: regulator@2089000 { + compatible = "qcom,saw2"; + reg = <0x02089000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + acc1: clock-controller@2098000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02098000 0x1000>, <0x02008000 0x1000>; }; - adm_dma: dma-controller@18300000 { - compatible = "qcom,adm"; - reg = <0x18300000 0x100000>; - interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; - #dma-cells = <1>; + saw1: regulator@2099000 { + compatible = "qcom,saw2"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; - clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; - clock-names = "core", "iface"; + nss_common: syscon@03000000 { + compatible = "syscon"; + reg = <0x03000000 0x0000FFFF>; + }; - resets = <&gcc ADM0_RESET>, - <&gcc ADM0_PBUS_RESET>, - <&gcc ADM0_C0_RESET>, - <&gcc ADM0_C1_RESET>, - <&gcc ADM0_C2_RESET>; - reset-names = "clk", "pbus", "c0", "c1", "c2"; - qcom,ee = <0>; + usb3_0: usb3@100f8800 { + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x100f8800 0x8000>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "core"; + + ranges; + + resets = <&gcc USB30_0_MASTER_RESET>; + reset-names = "master"; status = "disabled"; + + dwc3_0: dwc3@10000000 { + compatible = "snps,dwc3"; + reg = <0x10000000 0xcd00>; + interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hs_phy_0>, <&ss_phy_0>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + snps,dis_u3_susphy_quirk; + }; }; - saw0: regulator@2089000 { - compatible = "qcom,saw2"; - reg = <0x02089000 0x1000>, <0x02009000 0x1000>; - regulator; + hs_phy_0: phy@100f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; }; - saw1: regulator@2099000 { - compatible = "qcom,saw2"; - reg = <0x02099000 0x1000>, <0x02009000 0x1000>; - regulator; + ss_phy_0: phy@100f8830 { + compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + usb3_1: usb3@110f8800 { + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x110f8800 0x8000>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "core"; + + ranges; + + resets = <&gcc USB30_1_MASTER_RESET>; + reset-names = "master"; + + status = "disabled"; + + dwc3_1: dwc3@11000000 { + compatible = "snps,dwc3"; + reg = <0x11000000 0xcd00>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hs_phy_1>, <&ss_phy_1>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + snps,dis_u3_susphy_quirk; + }; + }; + + hs_phy_1: phy@110f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x110f8800 0x30>; + clocks = <&gcc USB30_1_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + ss_phy_1: phy@110f8830 { + compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x110f8830 0x30>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + sdcc3bam: dma-controller@12182000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12182000 0x8000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC3_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + sdcc1bam: dma-controller@12402000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12402000 0x8000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC1_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + amba: amba { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sdcc3: mmc@12180000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + status = "disabled"; + reg = <0x12180000 0x2000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <192000000>; + sd-uhs-sdr104; + sd-uhs-ddr50; + vqmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; + dma-names = "tx", "rx"; + }; + + sdcc1: mmc@12400000 { + status = "disabled"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + reg = <0x12400000 0x2000>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + max-frequency = <96000000>; + non-removable; + cap-sd-highspeed; + cap-mmc-highspeed; + mmc-ddr-1_8v; + vmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; + dma-names = "tx", "rx"; + }; }; gsbi1: gsbi@12440000 { @@ -654,56 +875,6 @@ i2c@16380000 { }; }; - gsbi5: gsbi@1a200000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <5>; - reg = <0x1a200000 0x100>; - clocks = <&gcc GSBI5_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - gsbi5_serial: serial@1a240000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x1a240000 0x1000>, - <0x1a200000 0x1000>; - interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@1a280000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - spi@1a280000 { - compatible = "qcom,spi-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - }; - gsbi6: gsbi@16500000 { compatible = "qcom,gsbi-v1.0.0"; reg = <0x16500000 0x100>; @@ -784,149 +955,119 @@ gsbi7_i2c: i2c@16680000 { }; }; - rng@1a500000 { - compatible = "qcom,prng"; - reg = <0x1a500000 0x200>; - clocks = <&gcc PRNG_CLK>; - clock-names = "core"; - }; + adm_dma: dma-controller@18300000 { + compatible = "qcom,adm"; + reg = <0x18300000 0x100000>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; - sata_phy: sata-phy@1b400000 { - compatible = "qcom,ipq806x-sata-phy"; - reg = <0x1b400000 0x200>; + clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; + clock-names = "core", "iface"; - clocks = <&gcc SATA_PHY_CFG_CLK>; - clock-names = "cfg"; + resets = <&gcc ADM0_RESET>, + <&gcc ADM0_PBUS_RESET>, + <&gcc ADM0_C0_RESET>, + <&gcc ADM0_C1_RESET>, + <&gcc ADM0_C2_RESET>; + reset-names = "clk", "pbus", "c0", "c1", "c2"; + qcom,ee = <0>; - #phy-cells = <0>; status = "disabled"; }; - nand: nand-controller@1ac00000 { - compatible = "qcom,ipq806x-nand"; - reg = <0x1ac00000 0x800>; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - clocks = <&gcc EBI2_CLK>, - <&gcc EBI2_AON_CLK>; - clock-names = "core", "aon"; - - dmas = <&adm_dma 3>; - dma-names = "rxtx"; - qcom,cmd-crci = <15>; - qcom,data-crci = <3>; - + gsbi5: gsbi@1a200000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <5>; + reg = <0x1a200000 0x100>; + clocks = <&gcc GSBI5_H_CLK>; + clock-names = "iface"; #address-cells = <1>; - #size-cells = <0>; - + #size-cells = <1>; + ranges; status = "disabled"; - }; - sata: sata@29000000 { - compatible = "qcom,ipq806x-ahci", "generic-ahci"; - reg = <0x29000000 0x180>; + syscon-tcsr = <&tcsr>; - interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + gsbi5_serial: serial@1a240000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x1a240000 0x1000>, + <0x1a200000 0x1000>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; - clocks = <&gcc SFAB_SATA_S_H_CLK>, - <&gcc SATA_H_CLK>, - <&gcc SATA_A_CLK>, - <&gcc SATA_RXOOB_CLK>, - <&gcc SATA_PMALIVE_CLK>; - clock-names = "slave_face", "iface", "core", - "rxoob", "pmalive"; + i2c@1a280000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; - assigned-clock-rates = <100000000>, <100000000>; + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; - phys = <&sata_phy>; - phy-names = "sata-phy"; - status = "disabled"; - }; + #address-cells = <1>; + #size-cells = <0>; + }; - qcom,ssbi@500000 { - compatible = "qcom,ssbi"; - reg = <0x00500000 0x1000>; - qcom,controller-type = "pmic-arbiter"; - }; + spi@1a280000 { + compatible = "qcom,spi-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - qfprom: qfprom@700000 { - compatible = "qcom,ipq8064-qfprom", "qcom,qfprom"; - reg = <0x00700000 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - speedbin_efuse: speedbin@c0 { - reg = <0xc0 0x4>; - }; - tsens_calib: calib@400 { - reg = <0x400 0xb>; - }; - tsens_calib_backup: calib_backup@410 { - reg = <0x410 0xb>; + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; }; }; - gcc: clock-controller@900000 { - compatible = "qcom,gcc-ipq8064", "syscon"; - clocks = <&pxo_board>, <&cxo_board>; - clock-names = "pxo", "cxo"; - reg = <0x00900000 0x4000>; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - - tsens: thermal-sensor@900000 { - compatible = "qcom,ipq8064-tsens"; - - nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; - nvmem-cell-names = "calib", "calib_backup"; - interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "uplow"; + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-ipq8064", "syscon"; + reg = <0x1a400000 0x100>; + }; - #qcom,sensors = <11>; - #thermal-sensor-cells = <1>; - }; + rng@1a500000 { + compatible = "qcom,prng"; + reg = <0x1a500000 0x200>; + clocks = <&gcc PRNG_CLK>; + clock-names = "core"; }; - rpm: rpm@108000 { - compatible = "qcom,rpm-ipq8064"; - reg = <0x108000 0x1000>; - qcom,ipc = <&l2cc 0x8 2>; + nand: nand-controller@1ac00000 { + compatible = "qcom,ipq806x-nand"; + reg = <0x1ac00000 0x800>; - interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "ack", "err", "wakeup"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; - clocks = <&gcc RPM_MSG_RAM_H_CLK>; - clock-names = "ram"; + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; - rpmcc: clock-controller { - compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; - #clock-cells = <1>; - }; - }; + #address-cells = <1>; + #size-cells = <0>; - tcsr: syscon@1a400000 { - compatible = "qcom,tcsr-ipq8064", "syscon"; - reg = <0x1a400000 0x100>; + status = "disabled"; }; - l2cc: clock-controller@2011000 { - compatible = "qcom,kpss-gcc", "syscon"; - reg = <0x2011000 0x1000>; - clocks = <&gcc PLL8_VOTE>, <&pxo_board>; - clock-names = "pll8_vote", "pxo"; - clock-output-names = "acpu_l2_aux"; - }; + sata_phy: sata-phy@1b400000 { + compatible = "qcom,ipq806x-sata-phy"; + reg = <0x1b400000 0x200>; - lcc: clock-controller@28000000 { - compatible = "qcom,lcc-ipq8064"; - reg = <0x28000000 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + status = "disabled"; }; pcie0: pci@1b500000 { @@ -1082,20 +1223,53 @@ pcie2: pci@1b900000 { perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; }; - nss_common: syscon@03000000 { - compatible = "syscon"; - reg = <0x03000000 0x0000FFFF>; - }; - qsgmii_csr: syscon@1bb00000 { compatible = "syscon"; reg = <0x1bb00000 0x000001FF>; }; - stmmac_axi_setup: stmmac-axi-config { - snps,wr_osr_lmt = <7>; - snps,rd_osr_lmt = <7>; - snps,blen = <16 0 0 0 0 0 0>; + lcc: clock-controller@28000000 { + compatible = "qcom,lcc-ipq8064"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + lpass@28100000 { + compatible = "qcom,lpass-cpu"; + status = "disabled"; + clocks = <&lcc AHBIX_CLK>, + <&lcc MI2S_OSR_CLK>, + <&lcc MI2S_BIT_CLK>; + clock-names = "ahbix-clk", + "mi2s-osr-clk", + "mi2s-bit-clk"; + interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "lpass-irq-lpaif"; + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; + }; + + sata: sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc SFAB_SATA_S_H_CLK>, + <&gcc SATA_H_CLK>, + <&gcc SATA_A_CLK>, + <&gcc SATA_RXOOB_CLK>, + <&gcc SATA_PMALIVE_CLK>; + clock-names = "slave_face", "iface", "core", + "rxoob", "pmalive"; + + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; + assigned-clock-rates = <100000000>, <100000000>; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + status = "disabled"; }; gmac0: ethernet@37000000 { @@ -1193,179 +1367,5 @@ gmac3: ethernet@37600000 { status = "disabled"; }; - - hs_phy_0: phy@100f8800 { - compatible = "qcom,ipq806x-usb-phy-hs"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_0: phy@100f8830 { - compatible = "qcom,ipq806x-usb-phy-ss"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_0: usb3@100f8800 { - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x100f8800 0x8000>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_0_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_0: dwc3@10000000 { - compatible = "snps,dwc3"; - reg = <0x10000000 0xcd00>; - interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; - phys = <&hs_phy_0>, <&ss_phy_0>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - hs_phy_1: phy@110f8800 { - compatible = "qcom,ipq806x-usb-phy-hs"; - reg = <0x110f8800 0x30>; - clocks = <&gcc USB30_1_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_1: phy@110f8830 { - compatible = "qcom,ipq806x-usb-phy-ss"; - reg = <0x110f8830 0x30>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_1: usb3@110f8800 { - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x110f8800 0x8000>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_1_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_1: dwc3@11000000 { - compatible = "snps,dwc3"; - reg = <0x11000000 0xcd00>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - phys = <&hs_phy_1>, <&ss_phy_1>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - vsdcc_fixed: vsdcc-regulator { - compatible = "regulator-fixed"; - regulator-name = "SDCC Power"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - sdcc1bam: dma-controller@12402000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12402000 0x8000>; - interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc SDC1_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - sdcc3bam: dma-controller@12182000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12182000 0x8000>; - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc SDC3_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - amba: amba { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - sdcc1: mmc@12400000 { - status = "disabled"; - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - reg = <0x12400000 0x2000>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - max-frequency = <96000000>; - non-removable; - cap-sd-highspeed; - cap-mmc-highspeed; - mmc-ddr-1_8v; - vmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; - dma-names = "tx", "rx"; - }; - - sdcc3: mmc@12180000 { - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - status = "disabled"; - reg = <0x12180000 0x2000>; - interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <192000000>; - sd-uhs-sdr104; - sd-uhs-ddr50; - vqmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; - dma-names = "tx", "rx"; - }; - }; - - sfpb_mutex: hwlock@1200600 { - compatible = "qcom,sfpb-mutex"; - reg = <0x01200600 0x100>; - - #hwlock-cells = <1>; - }; }; }; -- 2.36.1
