Hi Dmitry,
On Mon, Jul 11, 2022 at 10:37:32AM +0300, Dmitry Baryshkov wrote:
> Rather than reading the pdata->connector directly, fetch the connector
> using drm_atomic_state. This allows us to make pdata->connector optional
> (and thus supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR).
>
> Reviewed-by: Sam Ravnborg <sam@xxxxxxxxxxxx>
> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> ---
> drivers/gpu/drm/bridge/ti-sn65dsi86.c | 22 ++++++++++++++++------
> 1 file changed, 16 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi86.c b/drivers/gpu/drm/bridge/ti-sn65dsi86.c
> index d6dd4d99a229..b1b6ed3a8acc 100644
> --- a/drivers/gpu/drm/bridge/ti-sn65dsi86.c
> +++ b/drivers/gpu/drm/bridge/ti-sn65dsi86.c
> @@ -779,9 +779,9 @@ static void ti_sn_bridge_set_dsi_rate(struct ti_sn65dsi86 *pdata)
> regmap_write(pdata->regmap, SN_DSIA_CLK_FREQ_REG, val);
> }
>
> -static unsigned int ti_sn_bridge_get_bpp(struct ti_sn65dsi86 *pdata)
> +static unsigned int ti_sn_bridge_get_bpp(struct drm_connector *connector)
> {
> - if (pdata->connector->display_info.bpc <= 6)
> + if (connector->display_info.bpc <= 6)
> return 18;
> else
> return 24;
> @@ -796,7 +796,7 @@ static const unsigned int ti_sn_bridge_dp_rate_lut[] = {
> 0, 1620, 2160, 2430, 2700, 3240, 4320, 5400
> };
>
> -static int ti_sn_bridge_calc_min_dp_rate_idx(struct ti_sn65dsi86 *pdata)
> +static int ti_sn_bridge_calc_min_dp_rate_idx(struct ti_sn65dsi86 *pdata, unsigned int bpp)
> {
> unsigned int bit_rate_khz, dp_rate_mhz;
> unsigned int i;
> @@ -804,7 +804,7 @@ static int ti_sn_bridge_calc_min_dp_rate_idx(struct ti_sn65dsi86 *pdata)
> &pdata->bridge.encoder->crtc->state->adjusted_mode;
>
> /* Calculate minimum bit rate based on our pixel clock. */
> - bit_rate_khz = mode->clock * ti_sn_bridge_get_bpp(pdata);
> + bit_rate_khz = mode->clock * bpp;
>
> /* Calculate minimum DP data rate, taking 80% as per DP spec */
> dp_rate_mhz = DIV_ROUND_UP(bit_rate_khz * DP_CLK_FUDGE_NUM,
> @@ -1016,12 +1016,21 @@ static void ti_sn_bridge_atomic_enable(struct drm_bridge *bridge,
> struct drm_bridge_state *old_bridge_state)
> {
> struct ti_sn65dsi86 *pdata = bridge_to_ti_sn65dsi86(bridge);
> + struct drm_connector *connector;
> const char *last_err_str = "No supported DP rate";
> unsigned int valid_rates;
> int dp_rate_idx;
> unsigned int val;
> int ret = -EINVAL;
> int max_dp_lanes;
> + unsigned int bpp;
> +
> + connector = drm_atomic_get_new_connector_for_encoder(old_bridge_state->base.state,
> + bridge->encoder);
> + if (!connector) {
> + DRM_DEV_ERROR_RATELIMITED(pdata->dev, "Could not get the connector\n");
>From the documentation of DRM_DEV_ERROR_RATELIMITED:
* NOTE: this is deprecated in favor of drm_err_ratelimited() or
* dev_err_ratelimited().
Can you fix this, so we do not introduce deprecated functions/macros.
Sam
> + return;
> + }
>
> max_dp_lanes = ti_sn_get_max_lanes(pdata);
> pdata->dp_lanes = min(pdata->dp_lanes, max_dp_lanes);
> @@ -1047,8 +1056,9 @@ static void ti_sn_bridge_atomic_enable(struct drm_bridge *bridge,
> drm_dp_dpcd_writeb(&pdata->aux, DP_EDP_CONFIGURATION_SET,
> DP_ALTERNATE_SCRAMBLER_RESET_ENABLE);
>
> + bpp = ti_sn_bridge_get_bpp(connector);
> /* Set the DP output format (18 bpp or 24 bpp) */
> - val = (ti_sn_bridge_get_bpp(pdata) == 18) ? BPP_18_RGB : 0;
> + val = bpp == 18 ? BPP_18_RGB : 0;
> regmap_update_bits(pdata->regmap, SN_DATA_FORMAT_REG, BPP_18_RGB, val);
>
> /* DP lane config */
> @@ -1059,7 +1069,7 @@ static void ti_sn_bridge_atomic_enable(struct drm_bridge *bridge,
> valid_rates = ti_sn_bridge_read_valid_rates(pdata);
>
> /* Train until we run out of rates */
> - for (dp_rate_idx = ti_sn_bridge_calc_min_dp_rate_idx(pdata);
> + for (dp_rate_idx = ti_sn_bridge_calc_min_dp_rate_idx(pdata, bpp);
> dp_rate_idx < ARRAY_SIZE(ti_sn_bridge_dp_rate_lut);
> dp_rate_idx++) {
> if (!(valid_rates & BIT(dp_rate_idx)))
> --
> 2.35.1
