Lina Iyer <lina.iyer@xxxxxxxxxx> writes:
> Based on work by many authors, available at codeaurora.org
>
> SPM is a hardware block that controls the peripheral logic surrounding
> the application cores (cpu/l$). When the core executes WFI instruction,
> the SPM takes over the putting the core in low power state as
> configured. The wake up for the SPM is an interrupt at the GIC, which
> then completes the rest of low power mode sequence and brings the core
> out of low power mode.
>
> The SPM has a set of control registers that configure the SPMs
> individually based on the type of the core and the runtime conditions.
> SPM is a finite state machine block to which a sequence is provided and
> it interprets the bytes and executes them in sequence. Each low power
> mode that the core can enter into is provided to the SPM as a sequence.
>
> Configure the SPM to set the core (cpu or L2) into its low power mode,
> the index of the first command in the sequence is set in the SPM_CTL
> register. When the core executes ARM wfi instruction, it triggers the
> SPM state machine to start executing from that index. The SPM state
> machine waits until the interrupt occurs and starts executing the rest
> of the sequence until it hits the end of the sequence. The end of the
> sequence jumps the core out of its low power mode.
>
> Signed-off-by: Lina Iyer <lina.iyer@xxxxxxxxxx>
[...]
> +enum {
> + MSM_SPM_REG_SAW2_CFG,
> + MSM_SPM_REG_SAW2_AVS_CTL,
> + MSM_SPM_REG_SAW2_AVS_HYSTERESIS,
> + MSM_SPM_REG_SAW2_SPM_CTL,
> + MSM_SPM_REG_SAW2_PMIC_DLY,
> + MSM_SPM_REG_SAW2_AVS_LIMIT,
> + MSM_SPM_REG_SAW2_AVS_DLY,
> + MSM_SPM_REG_SAW2_SPM_DLY,
> + MSM_SPM_REG_SAW2_PMIC_DATA_0,
> + MSM_SPM_REG_SAW2_PMIC_DATA_1,
> + MSM_SPM_REG_SAW2_PMIC_DATA_2,
> + MSM_SPM_REG_SAW2_PMIC_DATA_3,
> + MSM_SPM_REG_SAW2_PMIC_DATA_4,
> + MSM_SPM_REG_SAW2_PMIC_DATA_5,
> + MSM_SPM_REG_SAW2_PMIC_DATA_6,
> + MSM_SPM_REG_SAW2_PMIC_DATA_7,
> + MSM_SPM_REG_SAW2_RST,
> +
> + MSM_SPM_REG_NR_INITIALIZE = MSM_SPM_REG_SAW2_RST,
> +
> + MSM_SPM_REG_SAW2_ID,
> + MSM_SPM_REG_SAW2_SECURE,
> + MSM_SPM_REG_SAW2_STS0,
> + MSM_SPM_REG_SAW2_STS1,
> + MSM_SPM_REG_SAW2_STS2,
> + MSM_SPM_REG_SAW2_VCTL,
> + MSM_SPM_REG_SAW2_SEQ_ENTRY,
> + MSM_SPM_REG_SAW2_SPM_STS,
> + MSM_SPM_REG_SAW2_AVS_STS,
> + MSM_SPM_REG_SAW2_PMIC_STS,
> + MSM_SPM_REG_SAW2_VERSION,
> +
> + MSM_SPM_REG_NR,
> +};
Do you really need the MSM_SPM_REG_ prefix on all of these? As these
names are all local to the driver, the extra prefix isn't needed IMO.
Also, consdiering that SPM seems to be sub-block of SAW2, the fact that
the SPM shows up twice in some of the names is a bit confusing.
Kevin
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
