Re: [PATCH] iio: iadc: Qualcomm SPMI PMIC current ADC driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Kiran,

On Fri, 2014-09-19 at 15:49 +0530, Kiran Padwal wrote:
> Hi Ivan,
> 
> On Thursday 18 September 2014 06:45 PM, Ivan T. Ivanov wrote:
> > The current ADC is peripheral of Qualcomm SPMI PMIC chips. It has
> > 16 bits resolution and register space inside PMIC accessible across
> > SPMI bus.
> > 
> > The driver registers itself through IIO interface.
> > 
> > Signed-off-by: Ivan T. Ivanov <iivanov@xxxxxxxxxx>
> > ---
> >  .../devicetree/bindings/iio/adc/qcom,spmi-iadc.txt |  61 ++
> 
> <snip>
> 
> > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> > index 11b048a..77274e4 100644
> > --- a/drivers/iio/adc/Kconfig
> > +++ b/drivers/iio/adc/Kconfig
> > @@ -279,4 +279,15 @@ config XILINX_XADC
> >  	  The driver can also be build as a module. If so, the module will be called
> >  	  xilinx-xadc.
> >  
> > +config QCOM_SPMI_IADC
> > +	tristate "Qualcomm SPMI PMIC current ADC"
> > +	select REGMAP_SPMI
> > +	depends on IIO
> 
> May be you need to add "SPMI" in depends on because without enabling that it breaks.

Right. 

> 
> > +	help
> > +	  This is the IIO Current ADC driver for Qualcomm QPNP IADC Chip.
> > +
> > +	  The driver supports single mode operation to read from upto seven channel
> > +	  configuration that include reading the external/internal Rsense, CSP_EX,
> > +	  CSN_EX pair along with the gain and offset calibration.
> > +
> >  endmenu
> 
> <snip>
> 
> > +
> > +	return iadc_write(iadc, IADC_EN_CTL1, data);
> > +}
> > +
> > +static void iadc_status_show(struct iadc_chip *iadc)
> > +{
> > +	u8 mode, sta1, chan, dig, en, req;
> 
> During compilation, getting a waring as below for all variables,
> 
> rivers/iio/adc/qcom-spmi-iadc.c: In function ‘iadc_poll_wait_eoc’:
> drivers/iio/adc/qcom-spmi-iadc.c:227:10: warning: ‘en’ may be used uninitialized in this function [-Wmaybe-uninitialized]
>   dev_warn(iadc->dev,
>           ^
> 

Right. I am not sure why I am not getting this warning.

> > +	int ret;
> > +
> > +	ret = iadc_read(iadc, IADC_MODE_CTL, &mode);
> > +	if (ret < 0)
> > +		return;
> > +
> > +	ret = iadc_read(iadc, IADC_DIG_PARAM, &dig);
> 

Thank you for review.

Regards,
Ivan

--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux