Re: [PATCH v8 1/3] dt-bindings: phy: qcom,usb-snps-femto-v2: Add phy override params bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 6/8/2022 3:06 PM, Krzysztof Kozlowski wrote:
On 01/06/2022 08:56, Krishna Kurapati wrote:
From: Sandeep Maheswaram <quic_c_sanm@xxxxxxxxxxx>

Add device tree bindings for SNPS phy tuning parameters.

Signed-off-by: Sandeep Maheswaram <quic_c_sanm@xxxxxxxxxxx>
Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
---
  .../bindings/phy/qcom,usb-snps-femto-v2.yaml       | 96 ++++++++++++++++++++++
  1 file changed, 96 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
index 1ce251d..daeeb04 100644
--- a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
@@ -53,6 +53,102 @@ properties:
    vdda33-supply:
      description: phandle to the regulator 3.3V supply node.
+ qcom,hs-disconnect-bp:
+    description:
+      This adjusts the voltage level for the threshold used to
+      detect a disconnect event at the host. Possible values are.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: -272
+    maximum: 2156
+
+  qcom,squelch-detector-bp:
+    description:
+      This adjusts the voltage level for the threshold used to
+      detect valid high-speed data.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: -2090
+    maximum: 1590
+
+  qcom,hs-amplitude-bp:
+    description:
+      This adjusts the high-speed DC level voltage.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: -660
+    maximum: 2670
+
+  qcom,pre-emphasis-duration-bp:
+    description:
+      This signal controls the duration for which the
+      HS pre-emphasis current is sourced onto DP<#> or DM<#>.
+      The HS Transmitter pre-emphasis duration is defined in terms of
+      unit amounts. One unit of pre-emphasis duration is approximately
+      650 ps and is defined as 1X pre-emphasis duration.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: 10000
+    maximum: 20000
+
+  qcom,pre-emphasis-amplitude-bp:
+    description:
+      This signal controls the amount of current sourced to
+      DP<#> and DM<#> after a J-to-K or K-to-J transition.
+      The HS Transmitter pre-emphasis current is defined in terms of unit
+      amounts. One unit amount is approximately 2 mA and is defined as
+      1X pre-emphasis current.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: 10000
+    maximum: 40000
+
+  qcom,hs-rise-fall-time-bp:
+    description:
+      This adjusts the rise/fall times of the high-speed waveform.
+      The values defined are in multiples of basis points (1bp = 0.01%).
+      The hardware accepts only discrete values. The value closest to the
+      provided input will be chosen as the override value for this param.
+    minimum: -4100
+    maximum: 5430
+
+  qcom,hs-crossover-voltage-microvolt:
+    description:
+      This adjusts the voltage at which the DP<#> and DM<#>
+      signals cross while transmitting in HS mode.
+      The values defined are in milli volts.
It's not accurate anymore - it's microvolt. I propose to skip this one
sentence, because unit is obvious from the type.

Hi Krzysztof,

Sure, will omit this line in the next series.

+    maximum: 28000
+
+  qcom,hs-output-impedance-micro-ohms:
+    description:
+      In some applications, there can be significant series resistance
+      on the D+ and D- paths between the transceiver and cable. This adjusts
+      the driver source impedance to compensate for added series
+      resistance on the USB. The values defined are in milli ohms.
The same. Other places might need similar change.

Best regards,
Krzysztof

Sure, Will make sure to remove the basis points sentence from other params as well as bp has been added to dtschema and is self-explanatory.


Thanks,

Krishna,




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux