Re: [PATCH v2] mailbox: qcom-ipcc: Log the pending interrupt during resume

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 5/16/22 6:57 PM, Manivannan Sadhasivam wrote:
On Thu, May 12, 2022 at 04:49:30PM +0530, Sibi Sankar wrote:


On 5/12/22 3:29 PM, Manivannan Sadhasivam wrote:
On Thu, May 12, 2022 at 03:08:43PM +0530, Sibi Sankar wrote:
Hey Mani,

Thanks for taking time to review the patch.

On 5/12/22 1:13 PM, Manivannan Sadhasivam wrote:
On Wed, May 11, 2022 at 12:13:24PM +0530, Sibi Sankar wrote:
From: Prasad Sodagudi <quic_psodagud@xxxxxxxxxxx>

Enable logging of the pending interrupt that triggered device wakeup. This
logging information helps to debug IRQs that cause periodic device wakeups
and prints the detailed information of pending IPCC interrupts instead of
the generic "Resume caused by IRQ 17, ipcc".

Scenario: Device wakeup caused by Modem crash
Logs:
qcom-ipcc mailbox: virq: 182 triggered client-id: 2; signal-id: 2

   From the IPCC bindings it can further understood that the client here is
IPCC_CLIENT_MPSS and the signal was IPCC_MPROC_SIGNAL_SMP2P.

Signed-off-by: Prasad Sodagudi <quic_psodagud@xxxxxxxxxxx>
Signed-off-by: Sibi Sankar <quic_sibis@xxxxxxxxxxx>
---

V2:
    * Fix build error when ipcc is a module [Kernel Test Bot]

    drivers/mailbox/qcom-ipcc.c | 27 +++++++++++++++++++++++++++
    1 file changed, 27 insertions(+)

diff --git a/drivers/mailbox/qcom-ipcc.c b/drivers/mailbox/qcom-ipcc.c
index c5d963222014..21c071ec119c 100644
--- a/drivers/mailbox/qcom-ipcc.c
+++ b/drivers/mailbox/qcom-ipcc.c
@@ -254,6 +254,28 @@ static int qcom_ipcc_setup_mbox(struct qcom_ipcc *ipcc,
    	return devm_mbox_controller_register(dev, mbox);
    }
+#ifdef CONFIG_PM_SLEEP

You don't need this guard anymore. Please see below.

ack


+static int qcom_ipcc_pm_resume(struct device *dev)
+{
+	struct qcom_ipcc *ipcc = dev_get_drvdata(dev);
+	u32 hwirq;
+	int virq;
+
+	hwirq = readl(ipcc->base + IPCC_REG_RECV_ID);
+	if (hwirq == IPCC_NO_PENDING_IRQ)
+		return 0;
+
+	virq = irq_find_mapping(ipcc->irq_domain, hwirq);
+
+	dev_info(dev, "virq: %d triggered client-id: %ld; signal-id: %ld\n", virq,
+		 FIELD_GET(IPCC_CLIENT_ID_MASK, hwirq), FIELD_GET(IPCC_SIGNAL_ID_MASK, hwirq));
+

Does this really need to be dev_info? This looks like a dev_dbg() material to
me.

The whole point of the log is to catch sporadic issues like random
wakeups caused by remoteprocs through ipcc. We would just end up with
a single line identifying the client id during resume if ipcc had indeed
caused the wakeup else it wouldn't print anything.


Right but that information is only required for debugging the periodic wakeups.
And that's not going to be useful for an end user.

I would consider this an extension to "Resume caused by IRQ xx, xxxx"

May I know from where it is coming? I couldn't grep it.

My bad I happened to have an out of tree patch in there. And it happens that all the logging done related to wakeup are under debug so I'll convert mine as well in v3. Thanks for the review!

-Sibi


print that we get to identify the wake up source. That's the reasoning
behind marking it as dev_info (being able to nail down random wakeups is
just an added advantage). That said I'll re-spin it with dbg if that's
the consensus.


I'll leave it up to Jassi to decide. But this patch looks good to me otherwise.

Reviewed-by: Manivannan Sadhasivam <mani@xxxxxxxxxx>

Thanks,
Mani


Thanks,
Mani

-Sibi

+	return 0;
+}
+#else
+#define qcom_ipcc_pm_resume NULL
+#endif
+
    static int qcom_ipcc_probe(struct platform_device *pdev)
    {
    	struct qcom_ipcc *ipcc;
@@ -324,6 +346,10 @@ static const struct of_device_id qcom_ipcc_of_match[] = {
    };
    MODULE_DEVICE_TABLE(of, qcom_ipcc_of_match);
+static const struct dev_pm_ops qcom_ipcc_dev_pm_ops = {
+	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(NULL, qcom_ipcc_pm_resume)
+};
+
    static struct platform_driver qcom_ipcc_driver = {
    	.probe = qcom_ipcc_probe,
    	.remove = qcom_ipcc_remove,
@@ -331,6 +357,7 @@ static struct platform_driver qcom_ipcc_driver = {
    		.name = "qcom-ipcc",
    		.of_match_table = qcom_ipcc_of_match,
    		.suppress_bind_attrs = true,
+		.pm = &qcom_ipcc_dev_pm_ops,

You can use the new pm_sleep_ptr() macro to avoid the PM_SLEEP guard.

		.pm = pm_sleep_ptr(&qcom_ipcc_dev_pm_ops),

ack


Thanks,
Mani

    	},
    };
--
2.7.4







[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux