Re: [PATCH v3 7/8] arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 14/05/2022 13:31, Marijn Suijten wrote:
On 2022-05-14 02:45:17, Dmitry Baryshkov wrote:
The IFC6560 is a board from Inforce Computing, built around the SDA660
SoC. This patch describes core clocks, some regulators from the two
PMICs, debug uart, storage, bluetooth and audio DSP remoteproc.

The regulator settings are inherited from prior work by Konrad Dybcio
and AngeloGioacchino Del Regno.

Co-developed-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
---
  arch/arm64/boot/dts/qcom/Makefile             |   1 +
  .../boot/dts/qcom/sda660-inforce-ifc6560.dts  | 455 ++++++++++++++++++
  2 files changed, 456 insertions(+)
  create mode 100644 arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index f9e6343acd03..5f717fe0e8d0 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -88,6 +88,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-herobrine-r1.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp2.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-crd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sda660-inforce-ifc6560.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-ganges-kirin.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-discovery.dtb
  dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-pioneer.dtb
diff --git a/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts b/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts
new file mode 100644
index 000000000000..ade5c27dafcf
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts
@@ -0,0 +1,455 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Ltd.
+ * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxx>
+ * Copyright (c) 2020, AngeloGioacchino Del Regno
+ *                     <angelogioacchino.delregno@xxxxxxxxxxxxxx>
+ */
+
+/dts-v1/;
+
+#include "sdm660.dtsi"
+#include "pm660.dtsi"
+#include "pm660l.dtsi"
+
+/ {
+	model = "Inforce 6560 Single Board Computer";
+	compatible = "inforce,ifc6560", "qcom,sda660";
+	chassis-type = "embedded"; /* SBC */
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		serial1 = &blsp2_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		volup {
+			label = "Volume Up";
+			gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	/*
+	 * Until we hook up type-c detection, we
+	 * have to stick with this. But it works.
+	 */
+	extcon_usb: extcon-usb {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&tlmm 58 GPIO_ACTIVE_HIGH>;
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7533_out>;
+			};
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	v3p3_bck_bst: v3p3-bck-bst-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v3p3_bck_bst";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	v1p2_ldo: v1p2-ldo-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v1p2_ldo";
+
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	v5p0_boost: v5p0-boost-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v5p0_boost";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&adsp_pil {
+	firmware-name = "qcom/ifc6560/adsp.mbn";
+};
+
+&blsp1_dma {
+	/*
+	 * The board will lock up if we toggle the BLSP clock, unless the
+	 * BAM DMA interconnects support is in place.
+	 */
+	/delete-property/ clocks;
+};
+
+&blsp_i2c6 {
+	status = "okay";
+
+	adv7533: hdmi@39 {
+		compatible = "adi,adv7535";
+		reg = <0x39>, <0x66>;
+		reg-names = "main", "edid";
+
+		interrupt-parent = <&pm660l_gpios>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+
+		clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+		clock-names = "cec";
+		/*
+		 * Limit to 3 lanes to prevent the bridge from changing amount
+		 * of lanes in the fly. MSM DSI host doesn't like that.
+		 */
+		adi,dsi-lanes = <3>;
+		avdd-supply = <&vreg_l13a_1p8>;
+		dvdd-supply = <&vreg_l13a_1p8>;
+		pvdd-supply = <&vreg_l13a_1p8>;
+		a2vdd-supply = <&vreg_l13a_1p8>;
+		v3p3-supply = <&v3p3_bck_bst>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				adv7533_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				adv7533_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_dma {
+	/*
+	 * The board will lock up if we toggle the BLSP clock, unless the
+	 * BAM DMA interconnects support is in place.
+	 */
+	/delete-property/ clocks;
+};
+
+&blsp2_uart1 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_l13a_1p8>;
+		vddxo-supply = <&vreg_l9a_1p8>;
+		vddrf-supply = <&vreg_l6a_1p3>;
+		vddch0-supply = <&vreg_l19a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l1a_1p225>;
+};
+
+&dsi0_out {
+	remote-endpoint = <&adv7533_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	status = "okay";
+	vcca-supply = <&vreg_l1b_0p925>;

@Konrad: It looks like we have this regulator downstream in mdss_dsi but
not in the upstream DT, is it missing by accident?

+};
+
+&mdss {
+	status = "okay";
+};
+
+&mmss_smmu {
+	status = "okay";
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+
+	linux,code = <KEY_VOLUMEUP>;
+};
+
+&qusb2phy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1b_0p925>;
+	vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
+};
+
+&qusb2phy1 {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1b_0p925>;
+	vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
+};
+
+&rpm_requests {
+	pm660-regulators {
+		compatible = "qcom,rpm-pm660-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+
+		vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>;
+		vdd_l2_l3-supply = <&vreg_s2b_1p05>;
+		vdd_l5-supply = <&vreg_s2b_1p05>;
+		vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>;
+		vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>;
+
+		vreg_s4a_2p04: s4 {
+			regulator-min-microvolt = <1805000>;
+			regulator-max-microvolt = <2040000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+			regulator-always-on;
+		};
+
+		vreg_s5a_1p35: s5 {
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_l1a_1p225: l1 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1250000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l6a_1p3: l6 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1368000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l8a_1p8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-system-load = <325000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1804000>;
+			regulator-max-microvolt = <1896000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l13a_1p8: l13 {
+			/* This gives power to the LPDDR4: never turn it off! */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1944000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		vreg_l19a_3p3: l19 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+	};
+
+	pm660l-regulators {
+		compatible = "qcom,rpm-pm660l-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+
+		vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>;
+		vdd_l2-supply = <&vreg_bob>;
+		vdd_l3_l5_l7_l8-supply = <&vreg_bob>;
+		vdd_l4_l6-supply = <&vreg_bob>;
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_s2b_1p05: s2 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_l1b_0p925: l1 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <925000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l2b_2p95: l2 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l4b_2p95: l4 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2952000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+
+			regulator-min-microamp = <200>;
+			regulator-max-microamp = <600000>;
+			regulator-system-load = <570000>;
+			regulator-allow-set-load;
+		};
+
+		/*
+		 * Downstream specifies a range of 1721-3600mV,
+		 * but the only assigned consumers are SDHCI2 VMMC
+		 * and Coresight QPDI that both request pinned 2.95V.
+		 * Tighten the range to 1.8-3.328 (closest to 3.3) to
+		 * make the mmc driver happy.
+		 */
+		vreg_l5b_2p95: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3328000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-system-load = <800000>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l7b_3p125: l7 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3125000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l8b_3p3: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3624000>;
+			regulator-enable-ramp-delay = <500>;
+			regulator-ramp-delay = <0>;
+		};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+	supports-cqe;
+
+	vmmc-supply = <&vreg_l4b_2p95>;
+	vqmmc-supply = <&vreg_l8a_1p8>;
+
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default";

Missing , "sleep".

+	pinctrl-0 = <&sdc2_state_on &sdc2_card_det_n>;
+	pinctrl1 = <&sdc2_state_off &sdc2_card_det_n>;

Missing hyphen.

Thanks.


+
+	vmmc-supply = <&vreg_l5b_2p95>;
+	vqmmc-supply = <&vreg_l2b_2p95>;
+
+	cd-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+	no-sdio;
+	no-emmc;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <8 4>;
+
+	sdc2_card_det_n: sd-card-det-n {
+		pins = "gpio54";
+		function = "gpio";
+		bias-pull-up;
+	};

It seems this pin is also already declared in sdc2-on/off in
sdm630.dtsi, with the same bias-pull-up in the -on case.  However, the
-off case sets bias-disable, won't that conflict?  (not in this moment,
because the clashing pinctrl pairs are "unused" with the typos above).

Ugh. Yes, there should be just one of them


I have always been under the impression this GPIO is board-specific and
should be moved out of sdm630.dtsi into board-specific DTs, is that
true?

Yes, it is true. That's why I didn't expect that it is already defined.
Also the bias and the drive-strength are also expected to go to the board files. Let me take a glance and fix that.


- Marijn

+};
+
+&usb2 {
+	status = "okay";
+};
+
+&usb2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	dr_mode = "peripheral";
+	extcon = <&extcon_usb>;
+};
--
2.35.1



--
With best wishes
Dmitry



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux