Hi,
On 09/08/2014 06:39 PM, Kumar Gala wrote:
> Add support for the Qualcomm AHCI SATA controller that exists on several
> SoC and specifically the IPQ806x family of chips. The IPQ806x SATA support
> requires the associated IPQ806x SATA PHY Driver to be enabled as well.
If I'm reading this driver correctly, all it does which ahci_platform.c does
not do is set the speed for 2 clocks, or am I missing something ?
If I'm correct, then why not simply use the following in the devicetree node ? :
sata@29000000 {
compatible = "qcom,ipq806x-ahci", "qcom,msm-ahci", "generic-ahci";
reg = <0x29000000 0x180>;
interrupts = <0 209 0x0>;
clocks = <&gcc SFAB_SATA_S_H_CLK>,
<&gcc SATA_H_CLK>,
<&gcc SATA_A_CLK>,
<&gcc SATA_RXOOB_CLK>,
<&gcc SATA_PMALIVE_CLK>;
clock-names = "slave_iface", "iface", "core",
"rxoob", "pmalive";
assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
assigned-clock-rates = <100000000>, <100000000>;
phys = <&sata_phy>;
phy-names = "sata-phy";
};
Notice the "generic-ahci" and assigned-clock* properties, see:
Documentation/devicetree/bindings/clock/clock-bindings.txt
With this you don't need to write your own driver at all, just a patch to
increase the max clocks + a dts node.
In case you do need your own driver for some reason see my review comments
on the driver further down.
>
> Signed-off-by: Kumar Gala <galak@xxxxxxxxxxxxxx>
> ---
> v4:
> * Added simple PM ops implementation
> * Added setting of pmalive clk
>
> v3:
> * Added comment about suspend/resume not supported
> * Fixup ahci_platform_init_host for upstream change to interface
> * cleanup error handling of rxoob clk, moved to devm_clk_get/put
>
> v2:
> * Fixed MODULE_LICENSE to be GPL v2
>
> drivers/ata/Kconfig | 10 +++++
> drivers/ata/Makefile | 1 +
> drivers/ata/ahci_qcom.c | 99 +++++++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 110 insertions(+)
> create mode 100644 drivers/ata/ahci_qcom.c
>
> diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
> index e1b9278..165d2fa 100644
> --- a/drivers/ata/Kconfig
> +++ b/drivers/ata/Kconfig
> @@ -133,6 +133,16 @@ config AHCI_MVEBU
>
> If unsure, say N.
>
> +config AHCI_QCOM
> + tristate "Qualcomm AHCI SATA support"
> + depends on ARCH_QCOM
> + help
> + This option enables support for AHCI SATA controller
> + integrated into Qualcomm ARM SoC chipsets. For more
> + information please refer to http://www.qualcomm.com/chipsets.
> +
> + If unsure, say N.
> +
> config AHCI_SUNXI
> tristate "Allwinner sunxi AHCI SATA support"
> depends on ARCH_SUNXI
> diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
> index ae41107..812435c 100644
> --- a/drivers/ata/Makefile
> +++ b/drivers/ata/Makefile
> @@ -13,6 +13,7 @@ obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o
> obj-$(CONFIG_AHCI_DA850) += ahci_da850.o libahci.o libahci_platform.o
> obj-$(CONFIG_AHCI_IMX) += ahci_imx.o libahci.o libahci_platform.o
> obj-$(CONFIG_AHCI_MVEBU) += ahci_mvebu.o libahci.o libahci_platform.o
> +obj-$(CONFIG_AHCI_QCOM) += ahci_qcom.o libahci.o libahci_platform.o
> obj-$(CONFIG_AHCI_SUNXI) += ahci_sunxi.o libahci.o libahci_platform.o
> obj-$(CONFIG_AHCI_ST) += ahci_st.o libahci.o libahci_platform.o
> obj-$(CONFIG_AHCI_TEGRA) += ahci_tegra.o libahci.o libahci_platform.o
> diff --git a/drivers/ata/ahci_qcom.c b/drivers/ata/ahci_qcom.c
> new file mode 100644
> index 0000000..3da0c94
> --- /dev/null
> +++ b/drivers/ata/ahci_qcom.c
> @@ -0,0 +1,99 @@
> +/*
> + * Qualcomm ARM SoC AHCI SATA platform driver
> + *
> + * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov
> + *
> + * Copyright (c) 2014, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/ahci_platform.h>
> +#include <linux/device.h>
> +#include <linux/kernel.h>
> +#include <linux/libata.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm.h>
> +#include "ahci.h"
> +
> +static const struct ata_port_info qcom_ahci_port_info = {
> + .flags = AHCI_FLAG_COMMON,
> + .pio_mask = ATA_PIO4,
> + .udma_mask = ATA_UDMA6,
> + .port_ops = &ahci_platform_ops,
> +};
> +
> +static int qcom_ahci_probe(struct platform_device *pdev)
> +{
> + struct ahci_host_priv *hpriv;
> + struct clk *rxoob_clk, *pmalive_clk;
> + int rc;
> +
> + hpriv = ahci_platform_get_resources(pdev);
> + if (IS_ERR(hpriv))
> + return PTR_ERR(hpriv);
> +
> + /* Try and set the rxoob clk to 100Mhz */
> + rxoob_clk = of_clk_get_by_name(pdev->dev.of_node, "rxoob");
> + if (IS_ERR(rxoob_clk))
> + return PTR_ERR(rxoob_clk);
You're leaking the reference to the clk you're getting here. Please do
one of the following to fix this:
1) Use devm_clk_get; or
2) Since ahci_platform_get_resources also got a reference,
you can put the clk after having set the rate; or
3) Since you specify a fixed clock order in your dts bindings, at defines
for the clock indexes, and just use hpriv->clks[DEFINE] to set the rates.
Otherwise this looks good, although I would prefer to not have a separate
driver for this at all, see above.
Regards,
Hans
> +
> + rc = clk_set_rate(rxoob_clk, 100000000);
> + if (rc)
> + return rc;
> +
> + /* Try and set the pmalive clk to 100Mhz */
> + pmalive_clk = of_clk_get_by_name(pdev->dev.of_node, "pmalive");
> + if (IS_ERR(pmalive_clk))
> + return PTR_ERR(pmalive_clk);
> +
> + rc = clk_set_rate(pmalive_clk, 100000000);
> + if (rc)
> + return rc;
> +
> + rc = ahci_platform_enable_resources(hpriv);
> + if (rc)
> + return rc;
> +
> + rc = ahci_platform_init_host(pdev, hpriv, &qcom_ahci_port_info);
> + if (rc)
> + goto disable_resources;
> +
> + return 0;
> +disable_resources:
> + ahci_platform_disable_resources(hpriv);
> + return rc;
> +}
> +
> +static const struct of_device_id qcom_ahci_of_match[] = {
> + { .compatible = "qcom,msm-ahci", },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, qcom_ahci_of_match);
> +
> +static SIMPLE_DEV_PM_OPS(qcom_ahci_pm_ops, ahci_platform_suspend,
> + ahci_platform_resume);
> +
> +static struct platform_driver qcom_ahci_driver = {
> + .probe = qcom_ahci_probe,
> + .remove = ata_platform_remove_one,
> + .driver = {
> + .name = "qcom_ahci_qcom",
> + .owner = THIS_MODULE,
> + .of_match_table = qcom_ahci_of_match,
> + .pm = &qcom_ahci_pm_ops,
> + },
> +};
> +module_platform_driver(qcom_ahci_driver);
> +
> +MODULE_DESCRIPTION("Qualcomm AHCI SATA platform driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("ahci:qcom");
>
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
