[PATCH v3] Bluetooth: btusb: add support for Qualcomm WCN785x

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Qualcomm WCN785x has PID/VID 0cf3/e700 as shown by
/sys/kernel/debug/usb/devices:

T:  Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  8 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e700 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  65 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  65 Ivl=1ms

Signed-off-by: Zijun Hu <quic_zijuhu@xxxxxxxxxxx>
---
 drivers/bluetooth/btusb.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 06a854a2507e..e6e28d3d1683 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -317,6 +317,11 @@ static const struct usb_device_id blacklist_table[] = {
 						     BTUSB_WIDEBAND_SPEECH |
 						     BTUSB_VALID_LE_STATES },
 
+	/* QCA WCN785x chipset */
+	{ USB_DEVICE(0x0cf3, 0xe700), .driver_info = BTUSB_QCA_WCN6855 |
+						     BTUSB_WIDEBAND_SPEECH |
+						     BTUSB_VALID_LE_STATES },
+
 	/* Broadcom BCM2035 */
 	{ USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
 	{ USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU },
@@ -3037,6 +3042,7 @@ static const struct qca_device_info qca_devices_table[] = {
 	{ 0x00130100, 40, 4, 16 }, /* WCN6855 1.0 */
 	{ 0x00130200, 40, 4, 16 }, /* WCN6855 2.0 */
 	{ 0x00130201, 40, 4, 16 }, /* WCN6855 2.1 */
+	{ 0x00190200, 40, 4, 16 }, /* WCN785x 2.0 */
 };
 
 static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request,
@@ -3327,11 +3333,11 @@ static int btusb_setup_qca(struct hci_dev *hdev)
 		if (err < 0)
 			return err;
 
-		/* WCN6855 2.1 will reset to apply firmware downloaded here, so
+		/* WCN6855 2.1 and later will reset to apply firmware downloaded here, so
 		 * wait ~100ms for reset Done then go ahead, otherwise, it maybe
 		 * cause potential enable failure.
 		 */
-		if (info->rom_version == 0x00130201)
+		if (info->rom_version >= 0x00130201)
 			msleep(QCA_BT_RESET_WAIT_MS);
 	}
 
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux