The huawei-g7 uses the msm8916-wcd-digital/analog audio codecs similar
to apq8016-sbc, so we can mostly copy paste it from there to make audio
work correctly. The main difference is the hphl-jack-type-normally-open
property, which is needed to avoid inverted audio jack detection.
Note that at least on my device the jack detection is not fully
reliable: sometimes headphones are detected as headsets (with
microphone). However, this is not a big problem for typical usage.
Signed-off-by: Stephan Gerhold <stephan@xxxxxxxxxxx>
---
.../arm64/boot/dts/qcom/msm8916-huawei-g7.dts | 46 +++++++++++++++++++
1 file changed, 46 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
index 8ad9eb436a0c..00488afb413d 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
@@ -8,6 +8,7 @@
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
/*
* Note: The original firmware from Huawei can only boot 32-bit kernels.
@@ -211,6 +212,10 @@ &blsp1_uart2 {
status = "okay";
};
+&lpass {
+ status = "okay";
+};
+
&pm8916_resin {
status = "okay";
linux,code = <KEY_VOLUMEDOWN>;
@@ -255,6 +260,40 @@ &sdhc_2 {
cd-gpios = <&msmgpio 56 GPIO_ACTIVE_LOW>;
};
+&sound {
+ status = "okay";
+
+ model = "msm8916";
+ audio-routing =
+ "AMIC1", "MIC BIAS External1",
+ "AMIC2", "MIC BIAS External2",
+ "AMIC3", "MIC BIAS External1";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cdc_pdm_lines_act>;
+ pinctrl-1 = <&cdc_pdm_lines_sus>;
+
+ primary-dai-link {
+ link-name = "WCD";
+ cpu {
+ sound-dai = <&lpass MI2S_PRIMARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
+ };
+ };
+
+ tertiary-dai-link {
+ link-name = "WCD-Capture";
+ cpu {
+ sound-dai = <&lpass MI2S_TERTIARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
+ };
+ };
+};
+
&usb {
status = "okay";
extcon = <&usb_id>, <&usb_id>;
@@ -264,6 +303,13 @@ &usb_hs_phy {
extcon = <&usb_id>;
};
+&wcd_codec {
+ qcom,micbias-lvl = <2800>;
+ qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+ qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+ qcom,hphl-jack-type-normally-open;
+};
+
&smd_rpm_regulators {
vdd_l1_l2_l3-supply = <&pm8916_s3>;
vdd_l4_l5_l6-supply = <&pm8916_s4>;
--
2.35.1
