Hi Sandeep,
On Tue, Mar 22, 2022 at 12:37:53PM +0530, Sandeep Maheswaram wrote:
> During suspend read the status of all port and make sure the PHYs
> are in the correct mode based on current speed.
> Phy interrupt masks are set based on this mode. Keep track of the mode
> of the HS PHY to be able to configure wakeup properly.
>
> Also check during suspend if any wakeup capable devices are
> connected to the controller (directly or through hubs), if there
> are none set a flag to indicate that the PHY is powered
> down during suspend.
>
> Signed-off-by: Sandeep Maheswaram <quic_c_sanm@xxxxxxxxxxx>
> ---
> drivers/usb/dwc3/core.c | 54 ++++++++++++++++++++++++++++++++++++++++---------
> 1 file changed, 45 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> index 1170b80..232a734 100644
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -32,12 +32,14 @@
> #include <linux/usb/gadget.h>
> #include <linux/usb/of.h>
> #include <linux/usb/otg.h>
> +#include <linux/usb/hcd.h>
>
> #include "core.h"
> #include "gadget.h"
> #include "io.h"
>
> #include "debug.h"
> +#include "../host/xhci.h"
>
> #define DWC3_DEFAULT_AUTOSUSPEND_DELAY 5000 /* ms */
>
> @@ -1861,10 +1863,36 @@ static int dwc3_core_init_for_resume(struct dwc3 *dwc)
> return ret;
> }
>
> +static void dwc3_set_phy_speed_mode(struct dwc3 *dwc)
> +{
> +
> + int i, num_ports;
> + u32 reg;
> + struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci);
> + struct xhci_hcd *xhci_hcd = hcd_to_xhci(hcd);
> +
> + dwc->hs_phy_mode = 0;
> +
> + reg = readl(&xhci_hcd->cap_regs->hcs_params1);
> +
> + num_ports = HCS_MAX_PORTS(reg);
> + for (i = 0; i < num_ports; i++) {
> + reg = readl(&xhci_hcd->op_regs->port_status_base + i * 0x04);
> + if (reg & PORT_PE) {
> + if (DEV_HIGHSPEED(reg) || DEV_FULLSPEED(reg))
> + dwc->hs_phy_mode |= PHY_MODE_USB_HOST_HS;
> + else if (DEV_LOWSPEED(reg))
> + dwc->hs_phy_mode |= PHY_MODE_USB_HOST_LS;
> + }
> + }
> + phy_set_mode(dwc->usb2_generic_phy, dwc->hs_phy_mode);
> +}
Are these flags cleared somewhere? Also qcom-snps-hs phy driver checks
for (hsphy->mode == PHY_MODE_USB_HOST) condition in qcom_snps_hsphy_suspend
to enable auto-resume. PHY_MODE_USB_HOST_HS/PHY_MODE_USB_HOST_LS flags
are different from PHY_MODE_USB_HOST. Currently this flag is set from
__dwc3_set_mode() when entering host mode. Can you clarify your intention
in calling phy_set_mode() here.
Thanks,
Pavan
