On 3/1/2022 6:19 AM, Doug Anderson wrote:
Thanks for Your Time Doug!!!
Hi,
On Fri, Feb 11, 2022 at 6:57 AM Srinivasa Rao Mandadapu
<quic_srivasam@xxxxxxxxxxx> wrote:
SC7280 has VA, TX and RX macros with SoundWire Controllers to attach with
codecs like WCD938x, max98360a using soundwire masters and i2s bus.
Add these nodes for sc7280 based platforms audio use case.
Add tlmm gpio property in wcd938x node for switching CTIA/OMTP Headset.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@xxxxxxxxxxx>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc7280-crd.dts | 4 +
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 178 +++++++++++++++++++++++++++++++
2 files changed, 182 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
index e2efbdd..dd23b63 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
@@ -84,6 +84,10 @@ ap_ts_pen_1v8: &i2c13 {
pins = "gpio51";
};
+&wcd938x {
+ us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
Probably need GPIO 81 pinctrl entry?
Okay. Will add it.
+};
+
&tlmm {
tp_int_odl: tp-int-odl {
pins = "gpio7";
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 1089fa0..07f8b1e 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -38,6 +38,14 @@
};
};
+ max98360a: audio-codec-0 {
nit that sorting should be based on node name here, so "audio" should
sort before "gpio-keys"
Okay. will sort acordingly.
+ compatible = "maxim,max98360a";
+ pinctrl-names = "default";
+ pinctrl-0 = <&_en>;
You refer to "amp_en", but I don't see it defined anywhere except in
"herobrine" files, so I don't think this will compile for you, will
it?
It's in dependent patch, which is in review state.
+ sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+ #sound-dai-cells = <0>;
+ };
+
nvme_3v3_regulator: nvme-3v3-regulator {
compatible = "regulator-fixed";
regulator-name = "VLDO_3V3";
@@ -49,6 +57,31 @@
pinctrl-names = "default";
pinctrl-0 = <&nvme_pwren>;
};
+
+ wcd938x: codec {
This is also sorted wrong.
Okay.
+ compatible = "qcom,wcd9380-codec";
+ #sound-dai-cells = <1>;
+
+ reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
Where's the pinctrl for GPIO 83?
Okay. Will add it.
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ vdd-rxtx-supply = <&vreg_l18b_1p8>;
+ vdd-io-supply = <&vreg_l18b_1p8>;
+ vdd-buck-supply = <&vreg_l17b_1p8>;
+ vdd-mic-bias-supply = <&vreg_bob>;
"vdd-mic-bias-supply" doesn't appear to be in your bindings.
Okay. will add it.
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000
+ 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ };
};
&apps_rsc {
@@ -496,6 +529,148 @@
drive-strength = <6>;
};
+&soc {
+ rxmacro: rxmacro@3200000 {
From the bindings document, I believe the node name should be
"codec@3200000", not "rxmacro@..."
Okay.
+ pinctrl-names = "default";
+ pinctrl-0 = <&rx_swr_active>;
+ compatible = "qcom,sc7280-lpass-rx-macro";
+ reg = <0 0x3200000 0 0x1000>;
The first two entries should be compatible and reg. Same for many places below.
Okay. will sort it.
+
+ clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
+ <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
+ <&vamacro>;
+ clock-names = "mclk", "npl", "fsgen";
Bindings document shows 5 clocks. You only specify 3. You either need
the extra clocks or you need to change the binding to allow for fewer.
Okay. will fix it.
+ power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
+ <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+ power-domain-names ="macro", "dcodec";
Why is power-domain stuff not in the bindings? Oh, I see. It's listed
as clocks there? You need to sort that out in the bindings.
Okay.
+ #clock-cells = <0>;
+ clock-frequency = <9600000>;
+ clock-output-names = "mclk";
+ #sound-dai-cells = <1>;
+ };
+
+ swr0: soundwire@3210000 {
+ reg = <0 0x3210000 0 0x2000>;
+ compatible = "qcom,soundwire-v1.6.0";
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rxmacro>;
+ clock-names = "iface";
+ label = "RX";
label is not in the bindings.
Okay. Will remove it as it's not being used.
+ qcom,din-ports = <0>;
+ qcom,dout-ports = <5>;
+ qcom,swrm-hctl-reg = <0x032a90a0>;
qcom,swrm-hctl-reg is not in the bindings, right? It also looks like a
magic value and probably should be broken out into something more
meaningful.
We have changed it as reset control. will update accordingly.
+ qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xFF 0xFF>;
+ qcom,ports-sinterval-low = /bits/ 8 <0x03 0x3F 0x1F 0x03 0x03>;
+ qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0B 0x01 0x01>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0B 0x00 0x00>;
+ qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xFF 0x00 0x01 0xFF 0xFF>;
+ qcom,ports-hstart = /bits/ 8 <0xFF 0x03 0xFF 0xFF 0xFF>;
+ qcom,ports-hstop = /bits/ 8 <0xFF 0x06 0xFF 0xFF 0xFF>;
+ qcom,ports-block-group-count = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0x00>;
+
+ #sound-dai-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ };
+
+ txmacro: txmacro@3220000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&tx_swr_active>;
+ compatible = "qcom,sc7280-lpass-tx-macro";
+ reg = <0 0x3220000 0 0x1000>;
+
+ clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
+ <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
+ <&vamacro>;
+ clock-names = "mclk", "npl", "fsgen";
+
+ power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
+ <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+ power-domain-names ="macro", "dcodec";
Again you've got mismatch w/ the bindings on clocks and power-domains.
Okay.
+ #clock-cells = <0>;
+ clock-frequency = <9600000>;
+ clock-output-names = "mclk";
+ #address-cells = <2>;
+ #size-cells = <2>;
Why address and size cells of 2???
Okay. It seems not required here. will remove it.
+ #sound-dai-cells = <1>;
+ };
+
+ swr1: soundwire@3230000 {
+ reg = <0 0x3230000 0 0x2000>;
+ compatible = "qcom,soundwire-v1.6.0";
+
+ interrupts-extended =
+ <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
+ <&pdc 130 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "swr_master_irq", "swr_wake_irq";
+ clocks = <&txmacro>;
+ clock-names = "iface";
+ label = "TX";
+
+ qcom,din-ports = <3>;
+ qcom,dout-ports = <0>;
+ qcom,swrm-hctl-reg = <0x032a90a8>;
+
+ qcom,ports-sinterval-low = /bits/ 8 <0x01 0x03 0x03>;
+ qcom,ports-offset1 = /bits/ 8 <0x01 0x00 0x02>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00>;
+ qcom,ports-hstart = /bits/ 8 <0xFF 0xFF 0xFF>;
+ qcom,ports-hstop = /bits/ 8 <0xFF 0xFF 0xFF>;
+ qcom,ports-word-length = /bits/ 8 <0xFF 0x0 0xFF>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xFF 0xFF 0xFF>;
+ qcom,ports-block-group-count = /bits/ 8 <0xFF 0xFF 0xFF>;
+ qcom,ports-lane-control = /bits/ 8 <0x00 0x01 0x00>;
+ qcom,port-offset = <1>;
+
+ #sound-dai-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ };
Same comments as with swr0.
Okay.
+ vamacro: codec@3370000 {
+ compatible = "qcom,sc7280-lpass-va-macro";
+ pinctrl-0 = <&dmic01_active>;
+ pinctrl-names = "default";
+
+ reg = <0 0x3370000 0 0x1000>;
+ clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>;
+ clock-names = "mclk";
+
+ power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
+ <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+ power-domain-names ="macro", "dcodec";
Again mismatch w/ bindings on clocks / power-domains.
Okay. will update bindings accordingly
+ #clock-cells = <0>;
+ clock-frequency = <9600000>;
+ clock-output-names = "fsgen";
+ #sound-dai-cells = <1>;
+ };
+};
+
+&swr0 {
This is in the same file, right? Just put it above right under the node.
Okay.
+ wcd_rx: wcd938x-hph-playback {
Please follow the bindings. Use the node name "codec" and include the
unit address, so this should be codec@0,4.
Okay.
+ compatible = "sdw20217010d00";
+ reg = <0 4>;
+ #sound-dai-cells = <1>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr1 {
+ wcd_tx: wcd938x-hph-capture {
+ compatible = "sdw20217010d00";
+ reg = <0 3>;
+ #sound-dai-cells = <1>;
+ qcom,tx-port-mapping = <1 2 3 4>;
+ };
Same comments as with swr0.
Okay.
