On Thu, 3 Mar 2022 at 14:43, Vinod Polimera <quic_vpolimer@xxxxxxxxxxx> wrote:
>
> - Some DPU versions support inline rot90. It is supported only for
> limited amount of UBWC formats.
> - There are two versions of inline rotators, v1 (present on sm8250 and
> sm7250) and v2 (sc7280). These versions differ in the list of supported
> formats and in the scaler possibilities.
>
> Changes in RFC:
> - Rebase changes to the latest code base.
> - Append rotation config variables with v2 and
> remove unused variables.(Dmitry)
> - Move pixel_ext setup separately from scaler3 config.(Dmitry)
> - Add 270 degree rotation to supported rotation list.(Dmitry)
>
> Changes in V2:
> - Remove unused macros and fix indentation.
> - Add check if 90 rotation is supported and add supported rotations to rot_cfg.
>
> Signed-off-by: Kalyan Thota <quic_kalyant@xxxxxxxxxxx>
> Signed-off-by: Vinod Polimera <quic_vpolimer@xxxxxxxxxxx>
> ---
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c | 44 +++++++---
> drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h | 17 ++++
> drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c | 108 +++++++++++++++++++------
> drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h | 2 +
> 4 files changed, 134 insertions(+), 37 deletions(-)
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> index aa75991..7cd07be 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c
> @@ -25,6 +25,9 @@
> #define VIG_SM8250_MASK \
> (VIG_MASK | BIT(DPU_SSPP_QOS_8LVL) | BIT(DPU_SSPP_SCALER_QSEED3LITE))
>
> +#define VIG_SC7280_MASK \
> + (VIG_SC7180_MASK | BIT(DPU_SSPP_INLINE_ROTATION))
> +
> #define DMA_SDM845_MASK \
> (BIT(DPU_SSPP_SRC) | BIT(DPU_SSPP_QOS) | BIT(DPU_SSPP_QOS_8LVL) |\
> BIT(DPU_SSPP_TS_PREFILL) | BIT(DPU_SSPP_TS_PREFILL_REC1) |\
> @@ -177,6 +180,11 @@ static const uint32_t plane_formats_yuv[] = {
> DRM_FORMAT_YVU420,
> };
>
> +static const uint32_t rotation_v2_formats[] = {
> + DRM_FORMAT_NV12,
> + /* TODO add formats after validation */
> +};
> +
> /*************************************************************
> * DPU sub blocks config
> *************************************************************/
> @@ -464,8 +472,7 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
> *************************************************************/
>
> /* SSPP common configuration */
> -
> -#define _VIG_SBLK(num, sdma_pri, qseed_ver) \
> +#define _VIG_SBLK(num, sdma_pri, qseed_ver, rot_cfg) \
> { \
> .maxdwnscale = MAX_DOWNSCALE_RATIO, \
> .maxupscale = MAX_UPSCALE_RATIO, \
> @@ -482,6 +489,7 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
> .num_formats = ARRAY_SIZE(plane_formats_yuv), \
> .virt_format_list = plane_formats, \
> .virt_num_formats = ARRAY_SIZE(plane_formats), \
> + .rotation_cfg = rot_cfg, \
> }
>
> #define _DMA_SBLK(num, sdma_pri) \
> @@ -497,14 +505,21 @@ static const struct dpu_ctl_cfg sc7280_ctl[] = {
> .virt_num_formats = ARRAY_SIZE(plane_formats), \
> }
>
> +static const struct dpu_rotation_cfg dpu_rot_sc7280_cfg_v2 = {
> + .rot_maxheight = 1088,
> + .rot_num_formats = ARRAY_SIZE(rotation_v2_formats),
> + .rot_format_list = rotation_v2_formats,
> + .rot_supported = DRM_MODE_ROTATE_MASK | DRM_MODE_REFLECT_MASK,
> +};
> +
> static const struct dpu_sspp_sub_blks sdm845_vig_sblk_0 =
> - _VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3);
> + _VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3, NULL);
> static const struct dpu_sspp_sub_blks sdm845_vig_sblk_1 =
> - _VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3);
> + _VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3, NULL);
> static const struct dpu_sspp_sub_blks sdm845_vig_sblk_2 =
> - _VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3);
> + _VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3, NULL);
> static const struct dpu_sspp_sub_blks sdm845_vig_sblk_3 =
> - _VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3);
> + _VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3, NULL);
>
> static const struct dpu_sspp_sub_blks sdm845_dma_sblk_0 = _DMA_SBLK("8", 1);
> static const struct dpu_sspp_sub_blks sdm845_dma_sblk_1 = _DMA_SBLK("9", 2);
> @@ -543,7 +558,10 @@ static const struct dpu_sspp_cfg sdm845_sspp[] = {
> };
>
> static const struct dpu_sspp_sub_blks sc7180_vig_sblk_0 =
> - _VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4);
> + _VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4, NULL);
> +
> +static const struct dpu_sspp_sub_blks sc7280_vig_sblk_0 =
> + _VIG_SBLK("0", 4, DPU_SSPP_SCALER_QSEED4, &dpu_rot_sc7280_cfg_v2);
>
> static const struct dpu_sspp_cfg sc7180_sspp[] = {
> SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
> @@ -557,13 +575,13 @@ static const struct dpu_sspp_cfg sc7180_sspp[] = {
> };
>
> static const struct dpu_sspp_sub_blks sm8250_vig_sblk_0 =
> - _VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3LITE);
> + _VIG_SBLK("0", 5, DPU_SSPP_SCALER_QSEED3LITE, NULL);
> static const struct dpu_sspp_sub_blks sm8250_vig_sblk_1 =
> - _VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3LITE);
> + _VIG_SBLK("1", 6, DPU_SSPP_SCALER_QSEED3LITE, NULL);
> static const struct dpu_sspp_sub_blks sm8250_vig_sblk_2 =
> - _VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3LITE);
> + _VIG_SBLK("2", 7, DPU_SSPP_SCALER_QSEED3LITE, NULL);
> static const struct dpu_sspp_sub_blks sm8250_vig_sblk_3 =
> - _VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3LITE);
> + _VIG_SBLK("3", 8, DPU_SSPP_SCALER_QSEED3LITE, NULL);
>
> static const struct dpu_sspp_cfg sm8250_sspp[] = {
> SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SM8250_MASK,
> @@ -585,8 +603,8 @@ static const struct dpu_sspp_cfg sm8250_sspp[] = {
> };
>
> static const struct dpu_sspp_cfg sc7280_sspp[] = {
> - SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7180_MASK,
> - sc7180_vig_sblk_0, 0, SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
> + SSPP_BLK("sspp_0", SSPP_VIG0, 0x4000, VIG_SC7280_MASK,
> + sc7280_vig_sblk_0, 0, SSPP_TYPE_VIG, DPU_CLK_CTRL_VIG0),
> SSPP_BLK("sspp_8", SSPP_DMA0, 0x24000, DMA_SDM845_MASK,
> sdm845_dma_sblk_0, 1, SSPP_TYPE_DMA, DPU_CLK_CTRL_DMA0),
> SSPP_BLK("sspp_9", SSPP_DMA1, 0x26000, DMA_CURSOR_SDM845_MASK,
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> index 31af04a..269eb45 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h
> @@ -109,6 +109,7 @@ enum {
> * @DPU_SSPP_TS_PREFILL Supports prefill with traffic shaper
> * @DPU_SSPP_TS_PREFILL_REC1 Supports prefill with traffic shaper multirec
> * @DPU_SSPP_CDP Supports client driven prefetch
> + * @DPU_SSPP_INLINE_ROTATION Support inline rotation
> * @DPU_SSPP_MAX maximum value
> */
> enum {
> @@ -129,6 +130,7 @@ enum {
> DPU_SSPP_TS_PREFILL,
> DPU_SSPP_TS_PREFILL_REC1,
> DPU_SSPP_CDP,
> + DPU_SSPP_INLINE_ROTATION,
> DPU_SSPP_MAX
> };
>
> @@ -312,6 +314,20 @@ struct dpu_qos_lut_tbl {
> };
>
> /**
> + * struct dpu_rotation_cfg - define inline rotation config
> + * @rot_maxheight: max pre rotated height allowed for rotation
> + * @rot_num_formats: count of the formats
> + * @rot_format_list: list of supported rotator formats
> + * @rot_supported: allowed rotations
> + */
> +struct dpu_rotation_cfg {
> + u32 rot_maxheight;
> + u32 rot_num_formats;
size_t
> + const u32 *rot_format_list;
> + u32 rot_supported;
> +};
> +
> +/**
> * struct dpu_caps - define DPU capabilities
> * @max_mixer_width max layer mixer line width support.
> * @max_mixer_blendstages max layer mixer blend stages or
> @@ -387,6 +403,7 @@ struct dpu_sspp_sub_blks {
> u32 num_formats;
> const u32 *virt_format_list;
> u32 virt_num_formats;
> + const struct dpu_rotation_cfg *rotation_cfg;
> };
>
> /**
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> index ca75089..031a0ff 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c
> @@ -528,11 +528,19 @@ static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
> struct dpu_plane_state *pstate,
> uint32_t src_w, uint32_t src_h, uint32_t dst_w, uint32_t dst_h,
> struct dpu_hw_scaler3_cfg *scale_cfg,
> - struct dpu_hw_pixel_ext *pixel_ext,
> const struct dpu_format *fmt,
> uint32_t chroma_subsmpl_h, uint32_t chroma_subsmpl_v)
> {
> uint32_t i;
> + bool inline_rotation = (pstate->rotation & DRM_MODE_ROTATE_90);
> +
> + /*
> + * For inline rotation cases, scaler config is post-rotation,
> + * so swap the dimensions here. However, pixel extension will
> + * need pre-rotation settings.
> + */
> + if (inline_rotation)
> + swap(src_w, src_h);
>
> scale_cfg->phase_step_x[DPU_SSPP_COMP_0] =
> mult_frac((1 << PHASE_STEP_SHIFT), src_w, dst_w);
> @@ -571,11 +579,6 @@ static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
> scale_cfg->preload_x[i] = DPU_QSEED3_DEFAULT_PRELOAD_H;
> scale_cfg->preload_y[i] = DPU_QSEED3_DEFAULT_PRELOAD_V;
> }
> -
> - pixel_ext->num_ext_pxls_top[i] =
> - scale_cfg->src_height[i];
> - pixel_ext->num_ext_pxls_left[i] =
> - scale_cfg->src_width[i];
> }
> if (!(DPU_FORMAT_IS_YUV(fmt)) && (src_h == dst_h)
> && (src_w == dst_w))
> @@ -591,6 +594,24 @@ static void _dpu_plane_setup_scaler3(struct dpu_plane *pdpu,
> scale_cfg->enable = 1;
> }
>
> +static void _dpu_plane_setup_pixel_ext(struct dpu_plane_state *pstate,
> + struct dpu_hw_scaler3_cfg *scale_cfg,
> + struct dpu_hw_pixel_ext *pixel_ext)
> +{
> + int i = 0;
> + bool inline_rotation = (pstate->rotation & DRM_MODE_ROTATE_90);
> +
> + if (!scale_cfg && !scale_cfg->enable)
> + return;
> +
> + for (i = 0; i < DPU_MAX_PLANES; i++) {
> + pixel_ext->num_ext_pxls_top[i] = inline_rotation ?
> + scale_cfg->src_width[i] : scale_cfg->src_height[i];
> + pixel_ext->num_ext_pxls_left[i] = inline_rotation ?
> + scale_cfg->src_height[i] : scale_cfg->src_width[i];
> + }
> +}
No. Please pass pre-scale config directly here, rather than reverting
the rotation.
You can safely pass drm_rect_height/_width of &pipe_cfg->src_rect to
this function.
> +
> static const struct dpu_csc_cfg dpu_csc_YUV2RGB_601L = {
> {
> /* S15.16 format */
> @@ -665,9 +686,12 @@ static void _dpu_plane_setup_scaler(struct dpu_plane *pdpu,
> drm_rect_height(&pipe_cfg->src_rect),
> drm_rect_width(&pipe_cfg->dst_rect),
> drm_rect_height(&pipe_cfg->dst_rect),
> - &scaler3_cfg, &pixel_ext, fmt,
> + &scaler3_cfg, fmt,
> info->hsub, info->vsub);
>
> + /* configure pixel extension based on scalar config */
> + _dpu_plane_setup_pixel_ext(pstate, &scaler3_cfg, &pixel_ext);
> +
> if (pdpu->pipe_hw->ops.setup_pe)
> pdpu->pipe_hw->ops.setup_pe(pdpu->pipe_hw,
> &pixel_ext);
> @@ -967,15 +991,17 @@ static int dpu_plane_atomic_check(struct drm_plane *plane,
> const struct dpu_format *fmt;
> struct drm_rect src, dst, fb_rect = { 0 };
> uint32_t min_src_size, max_linewidth;
> + unsigned int rotation = 0;
> + const struct dpu_sspp_cfg *pipe_hw_caps = pdpu->pipe_hw->cap;
>
> if (new_plane_state->crtc)
> crtc_state = drm_atomic_get_new_crtc_state(state,
> new_plane_state->crtc);
>
> - min_scale = FRAC_16_16(1, pdpu->pipe_hw->cap->sblk->maxupscale);
> + min_scale = FRAC_16_16(1, pipe_hw_caps->sblk->maxupscale);
> ret = drm_atomic_helper_check_plane_state(new_plane_state, crtc_state,
> min_scale,
> - pdpu->pipe_hw->cap->sblk->maxdwnscale << 16,
> + pipe_hw_caps->sblk->maxdwnscale << 16,
> true, true);
> if (ret) {
> DPU_DEBUG_PLANE(pdpu, "Check plane state failed (%d)\n", ret);
> @@ -1001,8 +1027,8 @@ static int dpu_plane_atomic_check(struct drm_plane *plane,
> min_src_size = DPU_FORMAT_IS_YUV(fmt) ? 2 : 1;
>
> if (DPU_FORMAT_IS_YUV(fmt) &&
> - (!(pdpu->pipe_hw->cap->features & DPU_SSPP_SCALER) ||
> - !(pdpu->pipe_hw->cap->features & DPU_SSPP_CSC_ANY))) {
> + (!(pipe_hw_caps->features & DPU_SSPP_SCALER) ||
> + !(pipe_hw_caps->features & DPU_SSPP_CSC_ANY))) {
> DPU_DEBUG_PLANE(pdpu,
> "plane doesn't have scaler/csc for yuv\n");
> return -EINVAL;
> @@ -1035,6 +1061,42 @@ static int dpu_plane_atomic_check(struct drm_plane *plane,
> return -E2BIG;
> }
>
> + if ((pipe_hw_caps->features & BIT(DPU_SSPP_INLINE_ROTATION)) &&
> + (pipe_hw_caps->sblk->rotation_cfg)) {
> + rotation = drm_rotation_simplify(new_plane_state->rotation,
> + pipe_hw_caps->sblk->rotation_cfg->rot_supported);
I think we can move rot_supported to SSPP capabilities. Then you can
use drm_rotation simplify() unconditionally. And move the check
whether INLINE_ROTATION is support to the code below
> +
> + if (rotation & DRM_MODE_ROTATE_90) {
Please move this code block to a separate function.
IOW
if (rotation & DRM_MODE_ROTATE_90) {
ret = dpu_plane_check_inline_rotation(....);
if (ret)
return ret;
}
> + bool found = false;
> + u32 i, num_formats;
> + const u32 *supported_formats;
> +
> + if ((drm_rect_width(&src) >
> + pipe_hw_caps->sblk->rotation_cfg->rot_maxheight)) {
> + DPU_DEBUG_PLANE(pdpu,
> + "invalid height for inline rot:%d max:%d\n",
> + src.y2, pipe_hw_caps->sblk->rotation_cfg->rot_maxheight);
> + return -EINVAL;
> + }
> +
> + supported_formats = pipe_hw_caps->sblk->rotation_cfg->rot_format_list;
> + num_formats = pipe_hw_caps->sblk->rotation_cfg->rot_num_formats;
> +
> + for (i = 0; i < num_formats; i++) {
> + /* check for valid formats supported by inline rotation */
> + if (fmt->base.pixel_format == supported_formats[i] &&
> + DPU_FORMAT_IS_UBWC(fmt))
> + found = true;
> + }
> +
> + if (!found || !num_formats) {
> + DPU_DEBUG_PLANE(pdpu,
> + "supported_format not found num:%d\n", num_formats);
> + return -EINVAL;
> + }
> + }
> + }
> + pstate->rotation = rotation;
So... If inline rotation is not supported, pstate->rotation is rather
than simplified rotation. Is this expected? Probably not.
> pstate->needs_qos_remap = drm_atomic_crtc_needs_modeset(crtc_state);
>
> return 0;
> @@ -1150,21 +1212,18 @@ static void dpu_plane_sspp_atomic_update(struct drm_plane *plane)
> pstate->multirect_mode);
>
> if (pdpu->pipe_hw->ops.setup_format) {
> - unsigned int rotation;
Slight hint: if you change this to:
unsigned int rotation =pstate->rotation;
you won't have to change the consequent lines.
>
> src_flags = 0x0;
>
> - rotation = drm_rotation_simplify(state->rotation,
> - DRM_MODE_ROTATE_0 |
> - DRM_MODE_REFLECT_X |
> - DRM_MODE_REFLECT_Y);
> -
> - if (rotation & DRM_MODE_REFLECT_X)
> + if (pstate->rotation & DRM_MODE_REFLECT_X)
> src_flags |= DPU_SSPP_FLIP_LR;
>
> - if (rotation & DRM_MODE_REFLECT_Y)
> + if (pstate->rotation & DRM_MODE_REFLECT_Y)
> src_flags |= DPU_SSPP_FLIP_UD;
>
> + if (pstate->rotation & DRM_MODE_ROTATE_90)
> + src_flags |= DPU_SSPP_ROT_90;
> +
> /* update format */
> pdpu->pipe_hw->ops.setup_format(pdpu->pipe_hw, fmt, src_flags,
> pstate->multirect_index);
> @@ -1462,6 +1521,8 @@ struct drm_plane *dpu_plane_init(struct drm_device *dev,
> int zpos_max = DPU_ZPOS_MAX;
> uint32_t num_formats;
> int ret = -EINVAL;
> + unsigned int supported_rotations = DRM_MODE_ROTATE_0 |
> + DRM_MODE_ROTATE_180 | DRM_MODE_REFLECT_X | DRM_MODE_REFLECT_Y;
>
> /* create and zero local structure */
> pdpu = kzalloc(sizeof(*pdpu), GFP_KERNEL);
> @@ -1529,12 +1590,11 @@ struct drm_plane *dpu_plane_init(struct drm_device *dev,
> BIT(DRM_MODE_BLEND_PREMULTI) |
> BIT(DRM_MODE_BLEND_COVERAGE));
>
> + if (pdpu->pipe_hw->cap->features & BIT(DPU_SSPP_INLINE_ROTATION))
> + supported_rotations |= DRM_MODE_ROTATE_90 | DRM_MODE_ROTATE_270;
> +
> drm_plane_create_rotation_property(plane,
> - DRM_MODE_ROTATE_0,
> - DRM_MODE_ROTATE_0 |
> - DRM_MODE_ROTATE_180 |
> - DRM_MODE_REFLECT_X |
> - DRM_MODE_REFLECT_Y);
> + DRM_MODE_ROTATE_0, supported_rotations);
>
> drm_plane_enable_fb_damage_clips(plane);
>
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> index 9d51dad..e72da02 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_plane.h
> @@ -25,6 +25,7 @@
> * @pending: whether the current update is still pending
> * @plane_fetch_bw: calculated BW per plane
> * @plane_clk: calculated clk per plane
> + * @rotation: simplified drm rotation hint
> */
> struct dpu_plane_state {
> struct drm_plane_state base;
> @@ -37,6 +38,7 @@ struct dpu_plane_state {
>
> u64 plane_fetch_bw;
> u64 plane_clk;
> + unsigned int rotation;
> };
>
> /**
> --
> 2.7.4
>
--
With best wishes
Dmitry
