> + pinctrl-names = "default";
> + pinctrl-0 = <&rx_swr_active>;
> + compatible = "qcom,sc7280-lpass-rx-macro";
> + reg = <0 0x3200000 0 0x1000>;
The first two entries should be compatible and reg. Same for many places below.
> +
> + clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
> + <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "fsgen";
Bindings document shows 5 clocks. You only specify 3. You either need
the extra clocks or you need to change the binding to allow for fewer.
> + power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
> + <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
> + power-domain-names ="macro", "dcodec";
Why is power-domain stuff not in the bindings? Oh, I see. It's listed
as clocks there? You need to sort that out in the bindings.
> + #clock-cells = <0>;
> + clock-frequency = <9600000>;
> + clock-output-names = "mclk";
> + #sound-dai-cells = <1>;
> + };
> +
> + swr0: soundwire@3210000 {
> + reg = <0 0x3210000 0 0x2000>;
> + compatible = "qcom,soundwire-v1.6.0";
> + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rxmacro>;
> + clock-names = "iface";
> + label = "RX";
label is not in the bindings.
> + qcom,din-ports = <0>;
> + qcom,dout-ports = <5>;
> + qcom,swrm-hctl-reg = <0x032a90a0>;
qcom,swrm-hctl-reg is not in the bindings, right? It also looks like a
magic value and probably should be broken out into something more
meaningful.
> + qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xFF 0xFF>;
> + qcom,ports-sinterval-low = /bits/ 8 <0x03 0x3F 0x1F 0x03 0x03>;
> + qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0B 0x01 0x01>;
> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0B 0x00 0x00>;
> + qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xFF 0x00 0x01 0xFF 0xFF>;
> + qcom,ports-hstart = /bits/ 8 <0xFF 0x03 0xFF 0xFF 0xFF>;
> + qcom,ports-hstop = /bits/ 8 <0xFF 0x06 0xFF 0xFF 0xFF>;
> + qcom,ports-block-group-count = /bits/ 8 <0xFF 0xFF 0xFF 0xFF 0x00>;
> +
> + #sound-dai-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + };
> +
> + txmacro: txmacro@3220000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&tx_swr_active>;
> + compatible = "qcom,sc7280-lpass-tx-macro";
> + reg = <0 0x3220000 0 0x1000>;
> +
> + clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
> + <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "fsgen";
> +
> + power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
> + <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
> + power-domain-names ="macro", "dcodec";
Again you've got mismatch w/ the bindings on clocks and power-domains.
> + #clock-cells = <0>;
> + clock-frequency = <9600000>;
> + clock-output-names = "mclk";
> + #address-cells = <2>;
> + #size-cells = <2>;
Why address and size cells of 2???
> + #sound-dai-cells = <1>;
> + };
> +
> + swr1: soundwire@3230000 {
> + reg = <0 0x3230000 0 0x2000>;
> + compatible = "qcom,soundwire-v1.6.0";
> +
> + interrupts-extended =
> + <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
> + <&pdc 130 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "swr_master_irq", "swr_wake_irq";
> + clocks = <&txmacro>;
> + clock-names = "iface";
> + label = "TX";
> +
> + qcom,din-ports = <3>;
> + qcom,dout-ports = <0>;
> + qcom,swrm-hctl-reg = <0x032a90a8>;
> +
> + qcom,ports-sinterval-low = /bits/ 8 <0x01 0x03 0x03>;
> + qcom,ports-offset1 = /bits/ 8 <0x01 0x00 0x02>;
> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00>;
> + qcom,ports-hstart = /bits/ 8 <0xFF 0xFF 0xFF>;
> + qcom,ports-hstop = /bits/ 8 <0xFF 0xFF 0xFF>;
> + qcom,ports-word-length = /bits/ 8 <0xFF 0x0 0xFF>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xFF 0xFF 0xFF>;
> + qcom,ports-block-group-count = /bits/ 8 <0xFF 0xFF 0xFF>;
> + qcom,ports-lane-control = /bits/ 8 <0x00 0x01 0x00>;
> + qcom,port-offset = <1>;
> +
> + #sound-dai-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + };
Same comments as with swr0.
> + vamacro: codec@3370000 {
> + compatible = "qcom,sc7280-lpass-va-macro";
> + pinctrl-0 = <&dmic01_active>;
> + pinctrl-names = "default";
> +
> + reg = <0 0x3370000 0 0x1000>;
> + clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>;
> + clock-names = "mclk";
> +
> + power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
> + <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
> + power-domain-names ="macro", "dcodec";
Again mismatch w/ bindings on clocks / power-domains.
> + #clock-cells = <0>;
> + clock-frequency = <9600000>;
> + clock-output-names = "fsgen";
> + #sound-dai-cells = <1>;
> + };
> +};
> +
> +&swr0 {
This is in the same file, right? Just put it above right under the node.
> + wcd_rx: wcd938x-hph-playback {
Please follow the bindings. Use the node name "codec" and include the
unit address, so this should be codec@0,4.
> + compatible = "sdw20217010d00";
> + reg = <0 4>;
> + #sound-dai-cells = <1>;
> + qcom,rx-port-mapping = <1 2 3 4 5>;
> + };
> +};
> +
> +&swr1 {
> + wcd_tx: wcd938x-hph-capture {
> + compatible = "sdw20217010d00";
> + reg = <0 3>;
> + #sound-dai-cells = <1>;
> + qcom,tx-port-mapping = <1 2 3 4>;
> + };
Same comments as with swr0.
