Enable the eDP display panel support without HPD on sc7280 platform.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@xxxxxxxxxxx>
---
Changes in v3:
- Sort the nodes alphabetically
- Use - instead of _ as node names
- Place the backlight and panel nodes under root
- Change the name of edp_out to mdss_edp_out
- Change the names of regulator nodes
- Delete unused properties in the board file
Changes in v2:
- Sort node references alphabetically
- Improve readability
- Move the pwm pinctrl to pwm node
- Move the regulators to root
- Define backlight power
- Remove dummy regulator node
- Cleanup pinctrl definitions
arch/arm64/boot/dts/qcom/sc7280-crd.dts | 122 ++++++++++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/sc7280.dtsi | 2 +-
2 files changed, 123 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
index e2efbdd..2a490a0 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
@@ -21,6 +21,59 @@
chosen {
stdout-path = "serial0:115200n8";
};
+
+ backlight_3v3_regulator: backlight-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "backlight_3v3_regulator";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_bl_power>;
+ };
+
+ edp_3v3_regulator: edp-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "edp_3v3_regulator";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_panel_power>;
+ };
+
+ edp_backlight: edp-backlight {
+ compatible = "pwm-backlight";
+
+ power-supply = <&backlight_3v3_regulator>;
+ pwms = <&pm8350c_pwm 3 65535>;
+ };
+
+ edp_panel: edp-panel {
+ compatible = "sharp,lq140m1jw46";
+
+ power-supply = <&edp_3v3_regulator>;
+ backlight = <&edp_backlight>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ edp_panel_in: endpoint {
+ remote-endpoint = <&edp_out>;
+ };
+ };
+ };
+ };
};
&apps_rsc {
@@ -76,6 +129,44 @@ ap_ts_pen_1v8: &i2c13 {
};
};
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dp_hot_plug_det>;
+ data-lanes = <0 1>;
+ vdda-1p2-supply = <&vreg_l6b_1p2>;
+ vdda-0p9-supply = <&vreg_l1b_0p8>;
+};
+
+&mdss_edp {
+ status = "okay";
+
+ vdda-1p2-supply = <&vreg_l6b_1p2>;
+ vdda-0p9-supply = <&vreg_l10c_0p8>;
+ /delete-property/ pinctrl-names;
+ /delete-property/ pinctrl-0;
+};
+
+&mdss_edp_out {
+ remote-endpoint = <&edp_panel_in>;
+};
+
+&mdss_edp_phy {
+ status = "okay";
+
+ vdda-1p2-supply = <&vreg_l6b_1p2>;
+ vdda-0p9-supply = <&vreg_l10c_0p8>;
+};
+
+&mdss_mdp {
+ status = "okay";
+};
+
&nvme_3v3_regulator {
gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
};
@@ -84,7 +175,38 @@ ap_ts_pen_1v8: &i2c13 {
pins = "gpio51";
};
+&pm8350c_gpios {
+ edp_bl_power: edp-bl-power {
+ pins = "gpio7";
+ function = "normal";
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ bias-disable;
+ output-low;
+ };
+
+ edp_bl_pwm: edp-bl-pwm {
+ pins = "gpio8";
+ function = "func1";
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ bias-disable;
+ output-low;
+ };
+};
+
+&pm8350c_pwm {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_bl_pwm>;
+};
+
&tlmm {
+ edp_panel_power: edp-panel-power {
+ pins = "gpio80";
+ function = "gpio";
+ bias-pull-down;
+ };
+
tp_int_odl: tp-int-odl {
pins = "gpio7";
function = "gpio";
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 3572399..eca403a 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -3066,7 +3066,7 @@
port@1 {
reg = <1>;
- edp_out: endpoint { };
+ mdss_edp_out: endpoint { };
};
};
--
2.7.4
