Add device tree binding support for the QCOM GSBI driver.
Signed-off-by: Andy Gross <agross@xxxxxxxxxxxxxx>
---
.../devicetree/bindings/soc/qcom/qcom,gsbi.txt | 78 ++++++++++++++++++++
1 file changed, 78 insertions(+)
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
new file mode 100644
index 0000000..6462e61
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt
@@ -0,0 +1,78 @@
+QCOM GSBI (General Serial Bus Interface) Driver
+
+The GSBI controller is modeled as a node with zero or more child nodes, each
+representing a serial sub-node device that is mux'd as part of the GSBI
+configuration settings. The mode setting will govern the input/output mode of
+the 4 GSBI IOs.
+
+Required properties:
+- compatible: must contain "qcom,gsbi-v1.0.0" for APQ8064/IPQ8064
+- reg: Address range for GSBI registers
+- clocks: required clock
+- clock-names: must contain "iface" entry
+- qcom,mode : indicates MUX value for configuration of the serial interface.
+ mode 0: idle, null values applied to all four GSBI IOs
+ mode 1: I2C on 2 ports, SIM/R-UIM on other 2.
+ mode 2: I2C
+ mode 3: SPI
+ mode 4: UART w/ flow control
+ mode 5: SIM/R-UIM
+ mode 6: I2C on 2 ports, UART (without flow control) on other 2
+ mode 7: undefined
+
+Required properties if child node exists:
+- #address-cells: Must be 1
+- #size-cells: Must be 1
+- ranges: Must be present
+
+Properties for children:
+
+A GSBI controller node can contain 0 or more child nodes representing serial
+devices. These serial devices can be a QCOM UART, I2C controller, spi
+controller, or some combination of aforementioned devices.
+
+See the following for child node definitions:
+Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
+Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
+Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
+
+Example for APQ8064:
+
+ gsbi4@16300000 {
+ compatible = "qcom,gsbi-v1.0.0";
+ reg = <0x16300000 0x100>;
+ clocks = <&gcc GSBI4_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ qcom,mode = <6>;
+
+ /* child nodes go under here */
+
+ i2c_qup4: i2c@16380000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x16380000 0x1000>;
+ interrupts = <0 153 0>;
+
+ clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
+ clock-names = "core", "iface";
+
+ clock-frequency = <200000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ };
+
+ uart4: serial@16340000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x16340000 0x1000>,
+ <0x16300000 0x1000>;
+ interrupts = <0 152 0x0>;
+ clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
+ clock-names = "core", "iface";
+ status = "ok";
+ };
+ };
+
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
