On Tue, Feb 11, 2014 at 02:58:52PM -0600, Andy Gross wrote:
> On Tue, Feb 11, 2014 at 11:00:48PM +0530, Vinod Koul wrote:
> > On Tue, Feb 04, 2014 at 02:42:35PM -0600, Andy Gross wrote:
> > > Add the DMA engine driver for the QCOM Bus Access Manager (BAM) DMA controller
> > > found in the MSM 8x74 platforms.
> > >
>
> > > +/**
> > > + * bam_alloc_chan - Allocate channel resources for DMA channel.
> > > + * @chan: specified channel
> > > + *
> > > + * This function allocates the FIFO descriptor memory
> > > + */
> > > +static int bam_alloc_chan(struct dma_chan *chan)
> > > +{
> > > + struct bam_chan *bchan = to_bam_chan(chan);
> > > + struct bam_device *bdev = bchan->bdev;
> > > +
> > > + /* allocate FIFO descriptor space, but only if necessary */
> > > + if (!bchan->fifo_virt) {
> > > + bchan->fifo_virt = dma_alloc_writecombine(bdev->dev,
> > > + BAM_DESC_FIFO_SIZE, &bchan->fifo_phys,
> > > + GFP_KERNEL);
> > > +
> > > + if (!bchan->fifo_virt) {
> > > + dev_err(bdev->dev, "Failed to allocate desc fifo\n");
> > > + return -ENOMEM;
> > > + }
> > > + }
> > > +
> > > + return BAM_DESC_FIFO_SIZE;
> > But you cna have SW descriptors more than HW ones and issue new ones once HW is
> > done with them. Why tie the limit to what HW supports and not create a better
> > driver?
>
> Given that the virt-dma only allows me to have one outstanding transaction that
> consumes the fifo, and that I allocate descriptors from kzalloc, this would be
> as many as you can get until you go OOM.
well you can update virt-dma to queue up multiple descriptors to HW is thats
supported :)
>
> The slave_sg() doesn't pull from a pool of descriptors. It uses kzalloc. So
> what value should I use for return value? Most drivers use 1.
Lots do 0 as they dont allocate descriptor here, they allocate when the
.prep_xxx call gets invoked, which is what I suspect from you case too.
>
> [....]
>
> > > +static void bam_slave_config(struct bam_chan *bchan,
> > > + struct dma_slave_config *cfg)
> > > +{
> > > + struct bam_device *bdev = bchan->bdev;
> > > + u32 maxburst;
> > > +
> > > + if (bchan->slave.direction == DMA_DEV_TO_MEM)
> > > + maxburst = bchan->slave.src_maxburst = cfg->src_maxburst;
> > > + else
> > > + maxburst = bchan->slave.dst_maxburst = cfg->dst_maxburst;
> > can you remove usage of slave.direction have save both. I am going to remove
> > this member...
> >
>
> Yes. no problem.
>
> [....]
>
> > > +
> > > +
> > > + /* allocate enough room to accomodate the number of entries */
> > > + async_desc = kzalloc(sizeof(*async_desc) +
> > > + (sg_len * sizeof(struct bam_desc_hw)), GFP_NOWAIT);
> > this seems to assume that each sg entry length will not exceed the HW capablity.
> > Does engine support any length descriptor, if not you may want to split to
> > multiple.
>
> Isn't this what the dma_set_max_seg_size supposed to fix? The client is not
> supposed to send segments larger than the max segment you can take. If that is
> true, then I have no issues.
Thats is true too, but do we want to limit this in driver ? This is more of a SW
limitation of who breaks up. for some like audio it makese sense but other not
too sure...
--
~Vinod
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
