On Aug 19, 2013, at 4:39 PM, Stephen Boyd wrote:
> The msm serial device bindings were added to the DTS files but
> never documented. Let's document them now and also fix things up
> so that it's clearer what hardware is supported. Instead of using
> hsuart (for high speed uart), let's use uartdm because that
> matches the actual name of the hardware. Also, let's add the
> version information in case we need to differentiate between
> different versions of the hardware in the future.
>
> Cc: David Brown <davidb@xxxxxxxxxxxxxx>
> Cc: <devicetree@xxxxxxxxxxxxxxx>
> Signed-off-by: Stephen Boyd <sboyd@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/serial/msm_serial.txt | 82 ++++++++++++++++++++++
> 1 file changed, 82 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/serial/msm_serial.txt
>
> diff --git a/Documentation/devicetree/bindings/serial/msm_serial.txt b/Documentation/devicetree/bindings/serial/msm_serial.txt
> new file mode 100644
> index 0000000..a6efac3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/serial/msm_serial.txt
> @@ -0,0 +1,82 @@
> +* MSM Serial UART and UARTDM
> +
> +There are two MSM serial hardware designs. UARTDM is designed for use with a
> +dma engine in high-speed use cases and the non-DM design is for lower speed use
> +cases. The two designs are mostly compatible from a software perspective except
> +the non-DM design can only read and write one character at a time and so the
> +register layout differs slightly.
I think you split this into two binding spec docs, one for each type of uart.
> +
> +UART
> +----
> +Required properties:
> +- compatible: Should contain "qcom,msm-uart"
> +- reg: Should contain UART register location and length. The first
first? is there more than one reg region?
> + register shall specify the main control registers
> +- interrupts: Should contain UART interrupt.
> +- clocks: Should contain the core clock.
> +- clock-names: Should be "core_clk".
> +
> +Optional properties:
> +- dmas: Should contain dma specifiers for transmit and receive
> +- dma-names: Should contain "tx" for transmit and "rx" for receive
confused, above you say the non-DM doesn't support DMA so, why the optional props?
> +
> +Example:
> +
> +A uart device with dma capabilities.
> +
> +serial@a9c00000 {
> + compatible = "qcom,msm-uart";
> + reg = <0xa9c00000 0x1000>;
> + interrupts = <11>;
> + clocks = <&uart_cxc>;
> + clock-names = "core_clk";
> + dmas = <&dma0 0>, <&dma0 1>;
> + dma-names = "tx", "rx";
> +};
> +
> +UARTDM
> +------
> +Required properties:
> +- compatible: Should contain at least "qcom,msm-uartdm".
> + A more specific property should be specified as follows depending
> + on the version:
> + "qcom,msm-uartdm-v1.1"
> + "qcom,msm-uartdm-v1.2"
> + "qcom,msm-uartdm-v1.3"
> + "qcom,msm-uartdm-v1.4"
> +- reg: Should contain UART register locations and lengths. The first
> + register shall specify the main control registers. An optional second
> + register location shall specify the GSBI control region.
Is GSBI region existing tied to particular versions (if so can we say that)
reg-names?
> +- interrupts: Should contain UART interrupt.
> +- clocks: Should contain the core clock and the ahb clock.
nit, ahb in caps?
> +- clock-names: Should be "core_clk" for the core clock and "iface_clk" for the
> + ahb clock.
> +
> +Optional properties:
> +- dmas: Should contain dma specifiers for transmit and receive channels
> +- dma-names: Should contain "tx" for transmit and "rx" for receive channels
> +
> +Examples:
> +
> +A uartdm v1.4 device with dma capabilities.
> +
> +serial@f991e000 {
> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> + reg = <0xf991e000 0x1000>;
> + interrupts = <0 108 0x0>;
> + clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>;
> + clock-names = "core_clk", "iface_clk";
> + dmas = <&dma0 0>, <&dma0 1>;
> + dma-names = "tx", "rx";
> +};
> +
> +A uartdm v1.3 device without dma capabilities.
> +
> +serial@19c40000 {
> + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
> + reg = <0x19c40000 0x1000>,
> + <0x19c00000 0x1000>;
> + interrupts = <0 195 0x0>;
> + clocks = <&gsbi5_uart_cxc>, <&gsbi5_ahb_cxc>;
> + clock-names = "core_clk", "iface_clk";
> +};
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> hosted by The Linux Foundation
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
