Re: [RFC PATCH v2 1/3] usb: dwc3: msm: Add device tree binding information

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Aug 09, 2013 at 10:31:58AM -0500, Kumar Gala wrote:
> 
> On Aug 9, 2013, at 4:53 AM, Ivan T. Ivanov wrote:
> 
> > From: "Ivan T. Ivanov" <iivanov@xxxxxxxxxx>
> > 
> > MSM USB3.0 core wrapper consist of USB3.0 IP (SNPS)
> 
> probably good to spell out Synopsys rather than SNPS

Synopsys (the company) has always used snps in their bindings though.

> > +Required properities :
> > +- compatible : sould be "qcom,dwc3-hsphy";
> > +- reg : offset and length of the register set in the memory map
> > +- clocks : phandles to clock instances of the device tree nodes
> > +- clock-names :
> > +	"xo" : External reference clock 19 MHz
> > +	"sleep_a_clk" : Sleep clock, used when USB3 core goes into low
> > +	power mode (U3).
> > +<supply-name>-supply : phandle to the regulator device tree node
> > +Required "supply-name" are:
> > +	"v1p8" : 1.8v supply for HSPHY
> > +	"v3p3" : 3.3v supply for HSPHY
> > +	"vbus" : vbus supply for host mode
> > +	"vddcx" : vdd supply for HS-PHY digital circuit operation

I believe these regulators belong to the PHY, not DWC3. Please write a
PHY driver.

> > +Required properities :
> > +- compatible : sould be "qcom,dwc3-ssphy";
> > +- reg : offset and length of the register set in the memory map
> > +- clocks : phandles to clock instances of the device tree nodes
> > +- clock-names :
> > +	"xo" : External reference clock 19 MHz
> > +	"ref_clk" : Reference clock - used in host mode.
> > +<supply-name>-supply : phandle to the regulator device tree node
> > +Required "supply-name" are:
> > +	"v1p8" : 1.8v supply for SS-PHY
> > +	"vddcx" : vdd supply for SS-PHY digital circuit operation

likewise, these regulators should be moved to the PHY driver.

> > +Required properties :
> > +- compatible : should be "qcom,dwc3"
> > +- reg : offset and length of the register set in the memory map
> > +	offset and length of the TCSR register for routing USB
> > +	signals to either picoPHY0 or picoPHY1.
> > +- clocks : phandles to clock instances of the device tree nodes
> > +- clock-names :
> > +	"core_clk" : Master/Core clock, have to be >= 125 MHz for SS
> > +	operation and >= 60MHz for HS operation
> > +	"iface_clk" : System bus AXI clock
> > +	"sleep_clk" : Sleep clock, used when USB3 core goes into low
> > +	power mode (U3).
> > +	"utmi_clk" : Generated by HS-PHY. Used to clock the low power
> > +	parts of thr HS Link layer.
> > +
> > +Optional properties :
> > +- gdsc-supply : phandle to the globally distributed switch controller
> > +  regulator node to the USB controller.
> > +
> > +Sub nodes:
> > +- Sub node for "DWC3 USB3 controller".
> > +  This sub node is required property for device node. The properties
> > +  of this subnode are specified in dwc3.txt.
> 
> Is tx-fifo-resize required for qcom,dwc3? if so we should call that
> out in the binding.

AFAICT that's only needed for OMAP5 ES1.0. Unless Qualcomm also screwed
up default TX FIFO sizes :-p

-- 
balbi

Attachment: signature.asc
Description: Digital signature


[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux