From: Manu Gautam <mgautam@xxxxxxxxxxxxxx> An Embedded Host High-Speed Electrical Test (EHSET) test fixture is used to initiate test modes on a host controller in order to perform the high speed electrical testing procedure for USB-IF compliance. When this test fixture is connected to a host, it can enumerate as one of several selectable VID/PID pairs, each corresponding to one of the following test modes: * TEST_SE0_NAK * TEST_J * TEST_K * TEST_PACKET * HS_HOST_PORT_SUSPEND_RESUME * SINGLE_STEP_GET_DEV_DESC * SINGLE_STEP_SET_FEATURE The USB EHSET procedure can be found here: http://www.usb.org/developers/onthego/EHSET_v1.01.pdf Signed-off-by: Manu Gautam <mgautam@xxxxxxxxxxxxxx> [jackp@xxxxxxxxxxxxxx: imported from commit 073c9409 on codeaurora.org; minor cleanup and updated author email] Signed-off-by: Jack Pham <jackp@xxxxxxxxxxxxxx> --- drivers/usb/misc/Kconfig | 13 ++++ drivers/usb/misc/Makefile | 1 + drivers/usb/misc/ehset.c | 134 +++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 148 insertions(+), 0 deletions(-) create mode 100644 drivers/usb/misc/ehset.c diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index a51e7d6..ca91420 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -200,6 +200,19 @@ config USB_TEST See <http://www.linux-usb.org/usbtest/> for more information, including sample test device firmware and "how to use it". +config USB_EHSET_TEST_FIXTURE + tristate "USB EHSET Test Fixture driver" + help + Say Y here if you want to support the special test fixture device + used for the USB-IF Embedded Host High-Speed Electrical Test procedure. + + When the test fixture is connected, it can enumerate as one of several + VID/PID pairs. This driver then initiates a corresponding test mode on + the downstream port to which the test fixture is attached. + + See <http://www.usb.org/developers/onthego/EHSET_v1.01.pdf> for more + information. + config USB_ISIGHTFW tristate "iSight firmware loading support" select FW_LOADER diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile index 3e1bd70..c9eafdf 100644 --- a/drivers/usb/misc/Makefile +++ b/drivers/usb/misc/Makefile @@ -22,6 +22,7 @@ obj-$(CONFIG_USB_LED) += usbled.o obj-$(CONFIG_USB_LEGOTOWER) += legousbtower.o obj-$(CONFIG_USB_RIO500) += rio500.o obj-$(CONFIG_USB_TEST) += usbtest.o +obj-$(CONFIG_USB_EHSET_TEST_FIXTURE) += ehset.o obj-$(CONFIG_USB_TRANCEVIBRATOR) += trancevibrator.o obj-$(CONFIG_USB_USS720) += uss720.o obj-$(CONFIG_USB_SEVSEG) += usbsevseg.o diff --git a/drivers/usb/misc/ehset.c b/drivers/usb/misc/ehset.c new file mode 100644 index 0000000..d2864b3 --- /dev/null +++ b/drivers/usb/misc/ehset.c @@ -0,0 +1,134 @@ +/* + * Copyright (c) 2010-2013, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/usb.h> +#include <linux/usb/ch11.h> + +#define TEST_SE0_NAK_PID 0x0101 +#define TEST_J_PID 0x0102 +#define TEST_K_PID 0x0103 +#define TEST_PACKET_PID 0x0104 +#define TEST_HS_HOST_PORT_SUSPEND_RESUME 0x0106 +#define TEST_SINGLE_STEP_GET_DEV_DESC 0x0107 +#define TEST_SINGLE_STEP_SET_FEATURE 0x0108 + +static int ehset_probe(struct usb_interface *intf, + const struct usb_device_id *id) +{ + int ret = -EINVAL; + struct usb_device *dev = interface_to_usbdev(intf); + struct usb_device *hub_udev = dev->parent; + struct usb_device_descriptor *buf; + u8 portnum = dev->portnum; + u16 test_pid = le16_to_cpu(dev->descriptor.idProduct); + + switch (test_pid) { + case TEST_SE0_NAK_PID: + ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0), + USB_REQ_SET_FEATURE, USB_RT_PORT, + USB_PORT_FEAT_TEST, + (TEST_SE0_NAK << 8) | portnum, + NULL, 0, 1000); + break; + case TEST_J_PID: + ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0), + USB_REQ_SET_FEATURE, USB_RT_PORT, + USB_PORT_FEAT_TEST, + (TEST_J << 8) | portnum, + NULL, 0, 1000); + break; + case TEST_K_PID: + ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0), + USB_REQ_SET_FEATURE, USB_RT_PORT, + USB_PORT_FEAT_TEST, + (TEST_K << 8) | portnum, + NULL, 0, 1000); + break; + case TEST_PACKET_PID: + ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0), + USB_REQ_SET_FEATURE, USB_RT_PORT, + USB_PORT_FEAT_TEST, + (TEST_PACKET << 8) | portnum, + NULL, 0, 1000); + break; + case TEST_HS_HOST_PORT_SUSPEND_RESUME: + /* Test: wait for 15secs -> suspend -> 15secs delay -> resume */ + msleep(15 * 1000); + ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0), + USB_REQ_SET_FEATURE, USB_RT_PORT, + USB_PORT_FEAT_SUSPEND, portnum, + NULL, 0, 1000); + if (ret < 0) + break; + + msleep(15 * 1000); + ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0), + USB_REQ_CLEAR_FEATURE, USB_RT_PORT, + USB_PORT_FEAT_SUSPEND, portnum, + NULL, 0, 1000); + break; + case TEST_SINGLE_STEP_GET_DEV_DESC: + /* Test: wait for 15secs -> GetDescriptor request */ + msleep(15 * 1000); + buf = kmalloc(USB_DT_DEVICE_SIZE, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), + USB_REQ_GET_DESCRIPTOR, USB_DIR_IN, + USB_DT_DEVICE << 8, 0, + buf, USB_DT_DEVICE_SIZE, + USB_CTRL_GET_TIMEOUT); + kfree(buf); + break; + case TEST_SINGLE_STEP_SET_FEATURE: + /* unsupported for now */ + default: + dev_err(&intf->dev, "%s: unsupported PID: 0x%x\n", + __func__, test_pid); + } + + return (ret < 0) ? ret : 0; +} + +static void ehset_disconnect(struct usb_interface *intf) +{ +} + +static const struct usb_device_id ehset_id_table[] = { + { USB_DEVICE(0x1a0a, TEST_SE0_NAK_PID) }, + { USB_DEVICE(0x1a0a, TEST_J_PID) }, + { USB_DEVICE(0x1a0a, TEST_K_PID) }, + { USB_DEVICE(0x1a0a, TEST_PACKET_PID) }, + { USB_DEVICE(0x1a0a, TEST_HS_HOST_PORT_SUSPEND_RESUME) }, + { USB_DEVICE(0x1a0a, TEST_SINGLE_STEP_GET_DEV_DESC) }, + { USB_DEVICE(0x1a0a, TEST_SINGLE_STEP_SET_FEATURE) }, + { } /* Terminating entry */ +}; +MODULE_DEVICE_TABLE(usb, ehset_id_table); + +static struct usb_driver ehset_driver = { + .name = "usb_ehset_test", + .probe = ehset_probe, + .disconnect = ehset_disconnect, + .id_table = ehset_id_table, +}; + +module_usb_driver(ehset_driver); + +MODULE_DESCRIPTION("USB Driver for EHSET Test Fixture"); +MODULE_LICENSE("GPL v2"); -- The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
