On Fri, Apr 12 2024 at 21:16, Russell King (Oracle) wrote:
> On Fri, Apr 12, 2024 at 08:30:40PM +0200, Rafael J. Wysocki wrote:
>> Say acpi_map_cpu) / acpi_unmap_cpu() are turned into arch calls.
>> What's the difference then? The locking, which should be fine if I'm
>> not mistaken and need_hotplug_init that needs to be set if this code
>> runs after the processor driver has loaded AFAICS.
>
> It is over this that I walked away from progressing this code, because
> I don't think it's quite as simple as you make it out to be.
>
> Yes, acpi_map_cpu() and acpi_unmap_cpu() are already arch implemented
> functions, so Arm64 can easily provide stubs for these that do nothing.
> That never caused me any concern.
>
> What does cause me great concern though are the finer details. For
> example, above you seem to drop the evaluation of _STA for the
> "make_present" case - I've no idea whether that is something that
> should be deleted or not (if it is something that can be deleted,
> then why not delete it now?)
>
> As for the cpu locking, I couldn't find anything in arch_register_cpu()
> that depends on the cpu_maps_update stuff nor needs the cpus_write_lock
> being taken - so I've no idea why the "make_present" case takes these
> locks.
Anything which updates a CPU mask, e.g. cpu_present_mask, after early
boot must hold the appropriate write locks. Otherwise it would be
possible to online a CPU which just got marked present, but the
registration has not completed yet.
> Finally, the "pr->flags.need_hotplug_init = 1" thing... it's not
> obvious that this is required - remember that with Arm64's "enabled"
> toggling, the "processor" is a slice of the system and doesn't
> actually go away - it's just "not enabled" for use.
>
> Again, as "processors" in Arm64 are slices of the system, they have
> to be fully described in ACPI before the OS boots, and they will be
> marked as being "present", which means they will be enumerated, and
> the driver will be probed. Any processor that is not to be used will
> not have its enabled bit set. It is my understanding that every
> processor will result in the ACPI processor driver being bound to it
> whether its enabled or not.
>
> The difference between real hotplug and Arm64 hotplug is that real
> hotplug makes stuff not-present (and thus unenumerable). Arm64 hotplug
> makes stuff not-enabled which is still enumerable.
Define "real hotplug" :)
Real physical hotplug does not really exist. That's at least true for
x86, where the physical hotplug support was chased for a while, but
never ended up in production.
Though virtualization happily jumped on it to hot add/remove CPUs
to/from a guest.
There are limitations to this and we learned it the hard way on X86. At
the end we came up with the following restrictions:
1) All possible CPUs have to be advertised at boot time via firmware
(ACPI/DT/whatever) independent of them being present at boot time
or not.
That guarantees proper sizing and ensures that associations
between hardware entities and software representations and the
resulting topology are stable for the lifetime of a system.
It is really required to know the full topology of the system at
boot time especially with hybrid CPUs where some of the cores
have hyperthreading and the others do not.
2) Hot add can only mark an already registered (possible) CPU
present. Adding non-registered CPUs after boot is not possible.
The CPU must have been registered in #1 already to ensure that
the system topology does not suddenly change in an incompatible
way at run-time.
The same restriction would apply to real physical hotplug. I don't think
that's any different for ARM64 or any other architecture.
Hope that helps.
Thanks,
tglx
