Hi!
I didn't go through all details. After you fix all comments below, you should
run "make dtbs_check" and fix all reported warnings too.
Dne nedelja, 06. junij 2021 ob 11:04:07 CEST je guoren@xxxxxxxxxx napisal(a):
> From: Guo Ren <guoren@xxxxxxxxxxxxxxxxx>
>
> Add initial DTS for Allwinner D1 NeZha board having only essential
> devices (uart, dummy, clock, reset, clint, plic, etc).
>
> Signed-off-by: Guo Ren <guoren@xxxxxxxxxxxxxxxxx>
> Co-Developed-by: Liu Shaohua <liush@xxxxxxxxxxxxxxxxx>
> Signed-off-by: Liu Shaohua <liush@xxxxxxxxxxxxxxxxx>
> Cc: Anup Patel <anup.patel@xxxxxxx>
> Cc: Atish Patra <atish.patra@xxxxxxx>
> Cc: Christoph Hellwig <hch@xxxxxx>
> Cc: Chen-Yu Tsai <wens@xxxxxxxx>
> Cc: Drew Fustini <drew@xxxxxxxxxxxxxxx>
> Cc: Maxime Ripard <maxime@xxxxxxxxxx>
> Cc: Palmer Dabbelt <palmerdabbelt@xxxxxxxxxx>
> Cc: Wei Fu <wefu@xxxxxxxxxx>
> Cc: Wei Wu <lazyparser@xxxxxxxxx>
> ---
> arch/riscv/boot/dts/Makefile | 1 +
> arch/riscv/boot/dts/allwinner/Makefile | 2 +
> .../boot/dts/allwinner/allwinner-d1-nezha-kit.dts | 29 ++++++++
> arch/riscv/boot/dts/allwinner/allwinner-d1.dtsi | 84
> ++++++++++++++++++++++ 4 files changed, 116 insertions(+)
> create mode 100644 arch/riscv/boot/dts/allwinner/Makefile
> create mode 100644 arch/riscv/boot/dts/allwinner/allwinner-d1-nezha-kit.dts
> create mode 100644 arch/riscv/boot/dts/allwinner/allwinner-d1.dtsi
>
> diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> index fe996b8..3e7b264 100644
> --- a/arch/riscv/boot/dts/Makefile
> +++ b/arch/riscv/boot/dts/Makefile
> @@ -2,5 +2,6 @@
> subdir-y += sifive
> subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> subdir-y += microchip
> +subdir-y += allwinner
>
> obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
> diff --git a/arch/riscv/boot/dts/allwinner/Makefile
> b/arch/riscv/boot/dts/allwinner/Makefile new file mode 100644
> index 00000000..4adbf4b
> --- /dev/null
> +++ b/arch/riscv/boot/dts/allwinner/Makefile
> @@ -0,0 +1,2 @@
> +# SPDX-License-Identifier: GPL-2.0
> +dtb-$(CONFIG_SOC_SUNXI) += allwinner-d1-nezha-kit.dtb
> diff --git a/arch/riscv/boot/dts/allwinner/allwinner-d1-nezha-kit.dts
> b/arch/riscv/boot/dts/allwinner/allwinner-d1-nezha-kit.dts new file mode
> 100644
> index 00000000..cd9f7c9
> --- /dev/null
> +++ b/arch/riscv/boot/dts/allwinner/allwinner-d1-nezha-kit.dts
Board DT names are comprised of soc name and board name, in this case it would
be "sun20i-d1-nezha-kit.dts"
> @@ -0,0 +1,29 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
Usually copyrights are added below spdx id.
> +
> +/dts-v1/;
> +
> +#include "allwinner-d1.dtsi"
> +
> +/ {
> + #address-cells = <2>;
> + #size-cells = <2>;
This should be part of SoC level DTSI.
> + model = "Allwinner D1 NeZha Kit";
> + compatible = "allwinner,d1-nezha-kit";
Board specific compatible string should be followed with SoC compatible, in
this case "allwinner,sun20i-d1". You should document it too.
> +
> + chosen {
> + bootargs = "console=ttyS0,115200";
Above line doesn't belong here. If anything, it should be added dynamically by
bootloader.
> + stdout-path = &serial0;
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0x0 0x40000000 0x0 0x20000000>;
> + };
Ditto for whole memory node.
> +
> + soc {
> + };
There is no point having empty nodes.
> +};
> +
> +&serial0 {
> + status = "okay";
> +};
> diff --git a/arch/riscv/boot/dts/allwinner/allwinner-d1.dtsi
> b/arch/riscv/boot/dts/allwinner/allwinner-d1.dtsi new file mode 100644
> index 00000000..11cd938
> --- /dev/null
> +++ b/arch/riscv/boot/dts/allwinner/allwinner-d1.dtsi
Current naming approach for Allwinner SoC level DTSI is "sun20i-d1.dtsi".
> @@ -0,0 +1,84 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +
> +/dts-v1/;
> +
> +/ {
> + #address-cells = <2>;
> + #size-cells = <2>;
Since all peripherals and memory are below 4 GiB, why have 64-bit addresses
and sizes? It just clutters DT.
> + model = "Allwinner D1 Soc";
> + compatible = "allwinner,d1-nezha-kit";
Compatible and model don't belong to SoC level DTSI.
> +
> + chosen {
> + };
Remove empty node.
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + timebase-frequency = <2400000>;
> + cpu@0 {
> + device_type = "cpu";
> + reg = <0>;
> + status = "okay";
> + compatible = "riscv";
> + riscv,isa = "rv64imafdcv";
> + mmu-type = "riscv,sv39";
> + cpu0_intc: interrupt-controller {
> + #interrupt-cells = <1>;
> + compatible = "riscv,cpu-intc";
> + interrupt-controller;
> + };
> + };
> + };
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "simple-bus";
> + ranges;
> +
> + reset: reset-sample {
> + compatible = "thead,reset-sample";
> + plic-delegate = <0x0 0x101ffffc>;
> + };
> +
> + clint: clint@14000000 {
> + compatible = "riscv,clint0";
> + interrupts-extended = <
> + &cpu0_intc 3 &cpu0_intc 7
> + >;
> + reg = <0x0 0x14000000 0x0 0x04000000>;
> + clint,has-no-64bit-mmio;
> + };
> +
> + plic: interrupt-controller@10000000 {
> + #interrupt-cells = <1>;
> + compatible = "riscv,plic0";
> + interrupt-controller;
> + interrupts-extended = <
> + &cpu0_intc 0xffffffff &cpu0_intc 9
> + >;
> + reg = <0x0 0x10000000 0x0 0x04000000>;
> + reg-names = "control";
> + riscv,max-priority = <7>;
> + riscv,ndev = <200>;
> + };
> +
> + dummy_apb: apb-clock {
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
> + clock-output-names = "dummy_apb";
> + #clock-cells = <0>;
> + };
> +
> + serial0: serial@2500000 {
This should be uart0 and board should have alias for it. Check ARM based
Allwinner DTs.
Best regards,
Jernej
> + compatible = "snps,dw-apb-uart";
> + reg = <0x0 0x02500000 0x0 0x400>;
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + interrupt-parent = <&plic>;
> + interrupts = <18>;
> + clocks = <&dummy_apb>;
> + status = "disabled";
> + };
> + };
> +};
