On Tue, Jan 20, 2015 at 3:37 PM, Lyra Zhang <zhang.lyra@xxxxxxxxx> wrote:
> Hi, Rob
>
> I still have a question to be conform, specific describes below:
>
> On Mon, Jan 19, 2015 at 10:11 PM, Rob Herring <robherring2@xxxxxxxxx> wrote:
>> On Mon, Jan 19, 2015 at 3:55 AM, Lyra Zhang <zhang.lyra@xxxxxxxxx> wrote:
>>> On Sat, Jan 17, 2015 at 12:41 AM, Rob Herring <robherring2@xxxxxxxxx> wrote:
>>>> On Fri, Jan 16, 2015 at 4:00 AM, Chunyan Zhang
>>>> <chunyan.zhang@xxxxxxxxxxxxxx> wrote:
>>>>> Add a full sc9836-uart driver for SC9836 SoC which is based on the
>>>>> spreadtrum sharkl64 platform.
>>>>> This driver also support earlycon.
>>>>> This patch also replaced the spaces between the macros and their
>>>>> values with the tabs in serial_core.h
>>
>> [...]
>>
>>>>> +static int __init sprd_serial_init(void)
>>>>> +{
>>>>> + int ret = 0;
>>>>> +
>>>>> + ret = uart_register_driver(&sprd_uart_driver);
>>>>
>>>> This can be done in probe now. Then you can use module_platform_driver().
>>>>
>>>
>>> Question:
>>> 1. there are 4 uart ports configured in dt for sprd_serial, so probe
>>> will be called 4 times, but uart_register_driver only needs to be
>>> called one time, so can we use uart_driver.state to check if
>>> uart_register_driver has already been called ?
>>
>> Yes.
>>
>>> 2. if I use module_platform_driver() instead of
>>> module_init(sprd_serial_init) and module_exit(sprd_serial_exit) , I
>>> must move uart_unregister_driver() which is now processed in
>>> sprd_serial_exit() to sprd_remove(), there is a similar problem with
>>> probe(), sprd_remove() will also be called 4 times, and actually it
>>> should be called only one time. How can we deal with this case?
>>
>> Look at pl01x or Samsung UART drivers which have done this conversion.
>
> Samsung UART does use module_platform_driver, but pl010/pl011 doesn't.
> In the Samsung UART driver, uart_unregister_driver is processed in
> remove(), like below:
>
> static int s3c24xx_serial_remove(struct platform_device *dev)
> {
> struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
>
> if (port) {
> s3c24xx_serial_cpufreq_deregister(to_ourport(port));
> uart_remove_one_port(&s3c24xx_uart_drv, port);
> }
>
> uart_unregister_driver(&s3c24xx_uart_drv);
> }
>
> if this serial has more than one ports, uart_unregister_driver() must
> be called multiple times when the device need to be removed.
> I think there may be a problem because that uart_unregister_driver()
> will do kfree(drv->state) every time when it's called.
I think it is no appropriate to call uart_unregister_driver() at first
port removing.
The drv->state buffer was shared with all uart ports.
If there are some cases that only 1 port is needed to be removed, that
will destroy all others, isn't it?
Regards,
Orson
>
> Thanks,
> Chunyan
>
>>
>>> 3. for the second question, we can check the platform_device->id, if
>>> it is equal to the index of last port (e.g. 4 for this case), then
>>> uart_unregister_driver() can be called. Does it work correctly? since
>>> for this case, we must keep the order of releasing ports.
>>
>> The id will not be the line index in the DT case. I don't think you
>> can guarantee the order either.
>>
>> It would be better to make uart_{un}register_driver deal with being
>> called multiple times so drivers don't have to deal with getting this
>> correct. I'm not sure if that is feasible though.
>>
>> Rob
--
To unsubscribe from this list: send the line "unsubscribe linux-api" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
