This patch adds a new capability to the 8250 driver framework. The Mediatek UART
port has a highspeed register to set the baudrate the port will work with.
This influences the calculation of the divisor.
Signed-off-by: Matthias Brugger <matthias.bgg@xxxxxxxxx>
---
drivers/tty/serial/8250/8250.h | 1 +
drivers/tty/serial/8250/8250_core.c | 47 +++++++++++++++++++++++++++++++++++
include/uapi/linux/serial_reg.h | 6 +++++
3 files changed, 54 insertions(+)
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 1ebf853..2b17655 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -70,6 +70,7 @@ struct serial8250_config {
#define UART_CAP_UUE (1 << 12) /* UART needs IER bit 6 set (Xscale) */
#define UART_CAP_RTOIE (1 << 13) /* UART needs IER bit 4 set (Xscale, Tegra) */
#define UART_CAP_HFIFO (1 << 14) /* UART has a "hidden" FIFO */
+#define UART_CAP_HIGHS (1 << 15) /* UART has a highspeed register (Mediatek) */
#define UART_BUG_QUOT (1 << 0) /* UART has buggy quot LSB */
#define UART_BUG_TXEN (1 << 1) /* UART has buggy TX IIR status */
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index 27f7ad6..a0c531b 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -2434,6 +2434,53 @@ serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
serial_dl_write(up, quot);
/*
+ * Mediatek UARTs use an extra highspeed register (UART_MTK_HIGHS)
+ *
+ * We need to recalcualte the quot register, as the claculation depends
+ * on the vaule in the highspeed register.
+ *
+ * Some baudrates are not supported by the chip, so we use the next
+ * lower rate supported.
+ *
+ * If highspeed register is set to 3, we need to specify sample count
+ * and sample point to increase accuracy. If not, we reset the
+ * registers to their default values.
+ */
+ if (up->port.flags & UART_CAP_HIGHS) {
+ if (baud <= 115200) {
+ serial_port_out(port, UART_MTK_HIGHS, 0x0);
+ } else if (baud <= 576000) {
+ serial_port_out(port, UART_MTK_HIGHS, 0x2);
+
+ /* Set to next lower baudrate supported */
+ if ((baud == 500000) || (baud == 576000))
+ baud = 460800;
+ quot = DIV_ROUND_CLOSEST(port->uartclk, 4 * baud);
+ } else {
+ serial_port_out(port, UART_MTK_HIGHS, 0x3);
+
+ /* Set to highest baudrate supported */
+ if (baud >= 1152000)
+ baud = 1000000;
+ quot = DIV_ROUND_CLOSEST(port->uartclk, 256 * baud);
+ }
+
+ serial_dl_write(up, quot);
+
+ if (baud > 460800) {
+ unsigned int tmp;
+
+ tmp = DIV_ROUND_CLOSEST(port->uartclk, quot * baud);
+ serial_port_out(port, UART_MTK_SAMPLE_COUNT, tmp - 1);
+ serial_port_out(port, UART_MTK_SAMPLE_POINT,
+ (tmp - 2) >> 1);
+ } else {
+ serial_port_out(port, UART_MTK_SAMPLE_COUNT, 0x00);
+ serial_port_out(port, UART_MTK_SAMPLE_POINT, 0xff);
+ }
+ }
+
+ /*
* XR17V35x UARTs have an extra fractional divisor register (DLD)
*
* We need to recalculate all of the registers, because DLM and DLL
diff --git a/include/uapi/linux/serial_reg.h b/include/uapi/linux/serial_reg.h
index 99b4705..f6dc97c 100644
--- a/include/uapi/linux/serial_reg.h
+++ b/include/uapi/linux/serial_reg.h
@@ -385,5 +385,11 @@
#define UART_EXAR_TXTRG 0x0a /* Tx FIFO trigger level write-only */
#define UART_EXAR_RXTRG 0x0b /* Rx FIFO trigger level write-only */
+/*
+ * These are definitions for the Mediatek UART
+ */
+#define UART_MTK_HIGHS 0x09 /* Highspeed register */
+#define UART_MTK_SAMPLE_COUNT 0x0a /* Sample count register */
+#define UART_MTK_SAMPLE_POINT 0x0b /* Sample point register */
#endif /* _LINUX_SERIAL_REG_H */
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-api" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
