Introduce ACPI mechanism to get PHYs registered on a MDIO bus and
provide them to be connected to MAC.
Describe properties "phy-handle" and "phy-mode".
Signed-off-by: Calvin Johnson <calvin.johnson@xxxxxxxxxxx>
---
Changes in v4:
- More cleanup
Changes in v3: None
Changes in v2:
- Updated with more description in document
Documentation/firmware-guide/acpi/dsd/phy.rst | 129 ++++++++++++++++++
1 file changed, 129 insertions(+)
create mode 100644 Documentation/firmware-guide/acpi/dsd/phy.rst
diff --git a/Documentation/firmware-guide/acpi/dsd/phy.rst b/Documentation/firmware-guide/acpi/dsd/phy.rst
new file mode 100644
index 000000000000..76fca994bc99
--- /dev/null
+++ b/Documentation/firmware-guide/acpi/dsd/phy.rst
@@ -0,0 +1,129 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=========================
+MDIO bus and PHYs in ACPI
+=========================
+
+The PHYs on an MDIO bus [1] are probed and registered using
+fwnode_mdiobus_register_phy().
+Later, for connecting these PHYs to MAC, the PHYs registered on the
+MDIO bus have to be referenced.
+
+The UUID given below should be used as mentioned in the "Device Properties
+UUID For _DSD" [2] document.
+ - UUID: daffd814-6eba-4d8c-8a91-bc9bbf4aa301
+
+This document introduces two _DSD properties that are to be used
+for PHYs on the MDIO bus.[3]
+
+phy-handle
+----------
+For each MAC node, a device property "phy-handle" is used to reference
+the PHY that is registered on an MDIO bus. This is mandatory for
+network interfaces that have PHYs connected to MAC via MDIO bus.
+
+During the MDIO bus driver initialization, PHYs on this bus are probed
+using the _ADR object as shown below and are registered on the MDIO bus.
+
+::
+ Scope(\_SB.MDI0)
+ {
+ Device(PHY1) {
+ Name (_ADR, 0x1)
+ } // end of PHY1
+
+ Device(PHY2) {
+ Name (_ADR, 0x2)
+ } // end of PHY2
+ }
+
+Later, during the MAC driver initialization, the registered PHY devices
+have to be retrieved from the MDIO bus. For this, MAC driver needs
+reference to the previously registered PHYs which are provided
+using reference to the device as {\_SB.MDI0.PHY1}.
+
+phy-mode
+--------
+The "phy-mode" _DSD property is used to describe the connection to
+the PHY. The valid values for "phy-mode" are defined in [4].
+
+
+An ASL example of this is shown below.
+
+DSDT entry for MDIO node
+------------------------
+The MDIO bus has an SoC component(MDIO controller) and a platform
+component (PHYs on the MDIO bus).
+
+a) Silicon Component
+This node describes the MDIO controller, MDI0
+---------------------------------------------
+::
+ Scope(_SB)
+ {
+ Device(MDI0) {
+ Name(_HID, "NXP0006")
+ Name(_CCA, 1)
+ Name(_UID, 0)
+ Name(_CRS, ResourceTemplate() {
+ Memory32Fixed(ReadWrite, MDI0_BASE, MDI_LEN)
+ Interrupt(ResourceConsumer, Level, ActiveHigh, Shared)
+ {
+ MDI0_IT
+ }
+ }) // end of _CRS for MDI0
+ } // end of MDI0
+ }
+
+b) Platform Component
+This node defines the PHYs that are connected to the MDIO bus, MDI0
+-------------------------------------------------------------------
+::
+ Scope(\_SB.MDI0)
+ {
+ Device(PHY1) {
+ Name (_ADR, 0x1)
+ } // end of PHY1
+
+ Device(PHY2) {
+ Name (_ADR, 0x2)
+ } // end of PHY2
+ }
+
+
+Below are the MAC nodes where PHY nodes are referenced.
+phy-mode and phy-handle are used as explained earlier.
+------------------------------------------------------
+::
+ Scope(\_SB.MCE0.PR17)
+ {
+ Name (_DSD, Package () {
+ ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
+ Package () {
+ Package (2) {"phy-mode", "rgmii-id"},
+ Package (2) {"phy-handle", \_SB.MDI0.PHY1}
+ }
+ })
+ }
+
+ Scope(\_SB.MCE0.PR18)
+ {
+ Name (_DSD, Package () {
+ ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
+ Package () {
+ Package (2) {"phy-mode", "rgmii-id"},
+ Package (2) {"phy-handle", \_SB.MDI0.PHY2}}
+ }
+ })
+ }
+
+References
+==========
+
+[1] Documentation/networking/phy.rst
+
+[2] https://www.uefi.org/sites/default/files/resources/_DSD-device-properties-UUID.pdf
+
+[3] Documentation/firmware-guide/acpi/DSD-properties-rules.rst
+
+[4] Documentation/devicetree/bindings/net/ethernet-controller.yaml
--
2.17.1
