Re: [PATCH v2] PCI/AER: Add support for reset of RCiEPs for APEI/Firmware first reporting only

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 3 Jul 2020, at 1:23, Jonathan Cameron wrote:

> On Thu, 2 Jul 2020 11:06:26 -0700
> Sean V Kelley <sean.v.kelley@xxxxxxxxxxxxxxx> wrote:
> 
> > On 26 Jun 2020, at 11:41, Jonathan Cameron wrote:
> > 
> > > On Fri, 26 Jun 2020 09:29:34 -0700
> > > Sean V Kelley <sean.v.kelley@xxxxxxxxxxxxxxx> wrote:
> > > 
> > > > Hi,
> > > Hi,
> > > 
> > > Thanks for taking a look.
> > > 
> > > > 
> > > > On 22 Jun 2020, at 4:44, Jonathan Cameron wrote:
> > > > 
> > > > > Was previously: PCI/AER: Add partial initial supprot for
> > > > > RCiEPs
> > > > > using
> > > > > RCEC or
> > > > > firmware first.
> > > > > 
> > > > > Currently the kernel does not handle AER errors for Root
> > > > > Complex
> > > > > integrated
> > > > > End Points (RCiEPs)[0].  These devices sit on a root bus
> > > > > within 
> > > > > the
> > > > > Root Complex
> > > > > (RC).  AER handling is performed by a Root Complex Event
> > > > > Collector
> > > > > (RCEC) [1]
> > > > > which is a effectively a type of RCiEP on the same root bus.
> > > > > 
> > > > > This code will only perform the correct reset flow for the
> > > > > case
> > > > > where
> > > > > there
> > > > > is no need to take any actions on the RCEC because the
> > > > > firmware is
> > > > > responsible for them.   This is true where APEI [2] is used
> > > > > to
> > > > > report
> > > > > the AER
> > > > > errors via a GHES[v2] HEST entry [3] and relevant AER CPER
> > > > > record
> > > > > [4]
> > > > > and Firmware
> > > > > First handling is in use.
> > > > 
> > > > Right, in the case of the RCEC one identifies the RCiEPs by
> > > > the 
> > > > RCiEP
> > > > bitmap as a part of the RCEC Associated Endpoint Extended
> > > > Capabilities.
> > > > This ‘search’ so to speak would make use also of the RCEC
> > > > Associated
> > > > Bus Numbers Register to associate the devices with an RCEC when
> > > > not
> > > > on
> > > > the same bus.
> > > 
> > > Ah. I'm afraid my access to recent specs is a bit limited at the
> > > moment.
> > > I do have a draft 5.0 spec which has that in though so I now see 
> > > what
> > > you mean.
> > > 
> > > Was introduced in Root Complex Event Collector Endpoint
> > > Association
> > > Extended
> > > Capability version 2 in PCIe 5.0 I think.
> > > 
> > 
> > Correct.
> > 
> > > > > As there is no current RCEC driver support, it should not be
> > > > > possible
> > > > > to get
> > > > > to this code via any routes other than the one above. Hence
> > > > > appropriate RCEC
> > > > > handling can be added when the RCEC driver support is ready.
> > > > > The error handling is different from a normal PCIe End Point
> > > > > because:
> > > > > 
> > > > > 1) There is no downstream port above an RCiEP as these
> > > > > devices sit
> > > > > on
> > > > > a root
> > > > >    bus.
> > > > > 
> > > > > 2) In general, it makes little sense to reset other devices
> > > > > on on
> > > > > the
> > > > > same
> > > > >    root bus.  For error handling outside the of the root
> > > > > complex
> > > > > (RC)
> > > > > an AER
> > > > >    error will indicate that all the topology below the
> > > > > physical
> > > > > link,
> > > > > which
> > > > >    the error is related to, will need to be reset as they
> > > > > share a
> > > > > common
> > > > >    path to the host.  For an RCiEP there is no such defined
> > > > > shared
> > > > > path
> > > > >    relationship with other elements on the root bus.
> > > > > 
> > > > > A new walk function, similar to pci_bus_walk is provided
> > > > > that 
> > > > > takes
> > > > > a
> > > > > pci_dev
> > > > > instead of a bus.  If that dev corresponds to a downstream
> > > > > port it
> > > > > will walk
> > > > > the subordinate bus of that downstream port.  If the dev does
> > > > > not
> > > > > then
> > > > > it
> > > > > will call the function on that device alone.   This function 
> > > > > allows
> > > > > us
> > > > > to
> > > > > avoid adding special cases to the majority of the error
> > > > > handling.
> > > > 
> > > > Then in that case the callback could add the additional checks
> > > > specific
> > > > to identifying the associated RCiEPs.
> > > 
> > > I am afraid I don't follow what you mean here.  Could you give
> > > more
> > > info?
> > 
> > Sure, a given RCEC can be associated with multiple RCiEPs.  As a
> > part 
> > of
> > the Extended Association Cap it is possible to obtain a bitmap of
> > the
> > RCiEP device ids on the same bus number as the RCEC device itself.
> > (5.0-1.0 sec 7.9.10.2).  With a Cap version of 2h or higher, it is 
> > also
> > possible to get an additional range of bus numbers containing
> > RCiEPs
> > also associated with this RCEC.
> > 
> > So I’m wondering if this function could be used in which passing a
> > dev, in this case the RCEC, triggers the call back which makes use
> > of
> > the RCiEP bitmap and associated bus ranges to return all identified
> > devices in use cases such as in AER for finding sources, etc.
> 
> Ah understood.
> 
> If we do this we effectively end up with 3 different types of walk
> and
> the meaning of the walk function gets more complex again.
> 
> 1) Normal bus walk - we pass the downstream port above a bus to which
> the device is attached and it walks everthing below that point.
> 
> 2) Case I care about RCiEP with no visible association with an RCEC
> as
> I don't need to walk devices.  In that case just calls the callbacks 
> for
> the actual device.
> 
> 3) Pass in RCiEP with RCEC asociated with it (or do a dance at the 
> caller
> to pass in the RCEC itself). Need to walk the devices that the RCEC
> is
> handling errors for.  For handling, I'm not all the calls will be 
> generally
> applicable to other devices associated with the RCEC as some only
> make
> sense if there is an actual PCIe bus involved and hence we need to 
> reset
> other devices on that bus.  For RCEC I don't think there is an 
> particular
> reason to assume an AER error reported at one RCiEP will have any 
> impact
> on other devices associated with the particular RCEC.
> I've not found anything in the spec addressing this question but 
> perhaps
> I've missed something?

Correct.  There should be no impact to the RCEC or its associated
RCiEPs which may not happen to reside on the same bus as the collector at all.

> However, if the RCEC doesn't support multiple error records, you may 
> need
> to walk the bus to identify multiple simultaneous issues, very 
> carefully
> avoiding (or least minimizing) race conditions.
> 
> > The alternative is to have a separate walk for RCECs that loops 
> > through
> > the bitmap / ranges (if supported) triggering the callback for each
> > device found.

I’ve been testing the Associated Endpoint Bitmap and Bus Range 
handling and using my pciutils patches to help to confirm some of the 
association. This overlaps with my CXL work and CXL 1.1 based RCiEPs
are good test cards:

(Decode via:  
https://lore.kernel.org/linux-pci/20200624223940.240463-1-sean.v.kelley@xxxxxxxxxxxxxxx/
 )

Test card at 6b:00.0

Capabilities: [e00 v1] Designated Vendor-Specific: Vendor=1e98 ID=0000
Rev=0 Len=56: CXL
CXLCap: Cache- IO+ Mem+ Mem HW Init+ HDMCount 1 Viral-
CXLCtl: Cache- IO+ Mem- Cache SF Cov 0 Cache SF Gran 0 Cache Clean-
Viral-
CXLSta: Viral-
Capabilities: [e38 v1] Device Serial Number 30-91-11-78-10-00-00-00

RCEC assocated to RCiEP at 6b while residing at 6a:

Capabilities: [160 v2] Root Complex Event Collector Endpoint
Association
RCiEPBitmap: 00000000 [none]
AssociatedBusNumbers: 6b-6b
Kernel driver in use: pcieport

with dmesg:

[ 10.502543] pcieport 0000:6a:00.4: AER: enabled with IRQ 34

The trick is the walk, which is not compact.  Currently working on
error injection to test:

void pcie_walk_rcec(struct pci_dev *rcec, int (*cb)(struct pci_dev *,
void *),
+                   void *userdata)
+{
+       u32 pos, bitmap, hdr, busn;
+       u8 ver, nextbusn, lastbusn;
+       unsigned int dev, fn, bnr;
+       struct pci_bus *pbus=NULL;
+       struct pci_dev *pdev;
+       int retval;
+
+       pos = pci_find_ext_capability(rcec, PCI_EXT_CAP_ID_RCEC);
+       if (!pos)
+               return;
+
+       pci_read_config_dword(rcec, pos + PCI_RCEC_RCIEP_BITMAP,
&bitmap);
+
+       for (dev = 0; dev < 32; dev++) {
+               if (!(bitmap & (1 << dev)))
+                       continue;
+
+               for (fn = 0; fn < 8; fn++) {
+                       pdev =
pci_get_domain_bus_and_slot(pci_domain_nr(rcec->bus),
+                                                          rcec->bus-
>number,
+                                                          PCI_DEVFN(de
v, fn));
+                       if (!pdev)
+                               continue;
+
+                       retval = cb(pdev, userdata);
+                       if (retval)
+                               return;
+               }
+       }

Then continuing in the same function above, I need to also consider the
case for the Bus ranges (still wip, not tested):

+       pci_read_config_dword(rcec, pos, &hdr);
+       ver = PCI_RCEC_EP_CAP_VER(hdr);
+       if (ver < PCI_RCEC_BUSN_REG_VER)
+               return;
+
+       pci_read_config_dword(rcec, pos + PCI_RCEC_BUSN, &busn);
+       nextbusn = PCI_RCEC_BUSN_NEXT(busn);
+       lastbusn = PCI_RCEC_BUSN_LAST(busn);
+
+       if ((nextbusn == 0xff) && (lastbusn == 0x00))
+               return;
+
+       for (bnr = nextbusn; bnr < (lastbusn + 1); bnr++) {
+               pbus = pci_find_bus(pci_domain_nr(rcec->bus), bnr);
+               if (pbus) {
+                       /* find RCiEP devices on the given bus */
+                       for (dev = 0; dev < 32; dev++) {
+ etc...
+                       }
+               }
+       }
+}

Currently this lives in aer.c and it's large enough that I wonder if
due to the specifity of the assoicated spec requirments if that should
be fine?

> Agreed. We would end up with the same splitting of handling paths
> that
> wasn't liked in my v1 patch.   Perhaps we need  single 
> pci_walk_aer_affected
> function with a pile of documentation for what it is actually doing?

Perhaps this would be a good start?  I tend to agree.  I can also
submit more of the patches as RFC for further comment.

> 
> Even then we may need to have a parameter to indicate a particular 
> callback
> should be restricted to devices that share a 'real bus' or not.

In my case 'walk' through the spec options of either just bitmap or if
of sufficient version (2h), I walk through the bus ranges, calling the
callback at each encounter.

> 
> I guess the proof will as ever be in what the code looks like.

Agreed.

> 
> Hmm. It increasingly feels like we may need to have a go at drawing 
> together
> some coherent documentation for the different ways of handling
> AER errors and specifications / assumptions for each.  Would be 
> 'interesting'
> to do given I'm fairly sure very few people actually understands all 
> the options and
> nasty corner cases!
> 
> +CC Lorenzo and James who may also be interested in this topic in 
> general.

Let's do.

Best regards,

Sean

> 
> Thanks,
> 
> Jonathan
> 
> 
> > Thanks,
> > 
> > Sean
> > 
> > > > > Open questions:
> > > > > 
> > > > > 1. Are we better protecting against link reset for an RCiEP
> > > > > in 
> > > > > here
> > > > > or
> > > > >    should we put the check in the link reset functions?
> > > > > 
> > > > > 2. If we were to get a stupid firmware record with the
> > > > > relevant
> > > > > reset
> > > > > flag
> > > > >    set to trigger a link reset, what is the correct
> > > > > response?  For
> > > > > now
> > > > > I
> > > > >    try to report that we haven't done anything and print a 
> > > > > warning.
> > > > > 
> > > > > 3. Naming of pci_walk_below_dev is rather unsatisfying. Any
> > > > > better
> > > > > ideas?
> > > > > 
> > > > > 4. pci_walk_below_dev is perhaps not of general utility.
> > > > > Shall I
> > > > > make
> > > > > it local
> > > > >    in err.c?  If not would a precursor patch for that be
> > > > > preferred?’
> > > > 
> > > > It depends.  Is it intended as a drop in replacement where
> > > > needed 
> > > > for
> > > > pci_walk_bus()? So in that case you are now passing the dev 
> > > > structure
> > > > and do the check for subordinate or is it intended as being 
> > > > specific
> > > > to
> > > > say RCEC? With AER, one could either first check for RC_EC type
> > > > before
> > > > using this one.  Or one could just drop in replace (passing the
> > > > dev
> > > > structure instead) and the call back performs the RCEC specific
> > > > checks
> > > > when a device is encountered.
> > > 
> > > If it is useful in aer.c that's great.   Just seemed such a weird
> > > beast
> > > I wasn't sure it would be of use anywhere else.
> > > 
> > > > > Testing has been performed via error injection on a QEMU
> > > > > platform 
> > > > > as
> > > > > that lets
> > > > > me create a wide range of topologies and report errors at
> > > > > any 
> > > > > chosen
> > > > > location.
> > > > > Currently I have no plans to upstream this injection support,
> > > > > but 
> > > > > am
> > > > > happy to
> > > > > share if useful to others.
> > > > 
> > > > I’m experimenting with it in my RCEC code in AER and will give 
> > > > you
> > > > additional feedback.
> > > 
> > > Great, thanks
> > > 
> > > Jonathan
> > > 
> > > > Thanks,
> > > > 
> > > > Sean
> > > > 
> > > > 
> > > > > [0] ACPI PCI Express Base Specification 4.0 1.3.2.3 Root
> > > > > Complex
> > > > > Integrated
> > > > >     Endpoint Rules.
> > > > > [1] ACPI PCI Express Base Specification 4.0 6.2 Error
> > > > > Signalling 
> > > > > and
> > > > > Logging
> > > > > [2] ACPI Specification 6.3 Chapter 18 ACPI Platform Error 
> > > > > Interface
> > > > > (APEI)
> > > > > [3] ACPI Sepcification 6.3 18.2.3.7 Generic Hardware Error
> > > > > Source
> > > > > [4] UEFI Specification 2.8, N.2.7 PCI Express Error Section
> > > > > 
> > > > > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
> > > > > ---
> > > > > Changes since v1:
> > > > > * Separated from the largely unrelated fix so the two can
> > > > > move
> > > > > forwards separately.
> > > > > * Instead of separate path for RCiEP handling use the method
> > > > > suggested
> > > > > by Bjorn
> > > > >   and Sathyanarayanan with an adjusted pci_bus_walk.
> > > > > 
> > > > > Thanks all for reviews of V1.
> > > > > 
> > > > >  drivers/pci/bus.c      | 28 ++++++++++++++++++++++++++++
> > > > >  drivers/pci/pcie/err.c | 29 +++++++++++++++++++----------
> > > > >  include/linux/pci.h    |  2 ++
> > > > >  3 files changed, 49 insertions(+), 10 deletions(-)
> > > > > 
> > > > > diff --git a/drivers/pci/bus.c b/drivers/pci/bus.c
> > > > > index 8e40b3e6da77..7cbe1ed2db3d 100644
> > > > > --- a/drivers/pci/bus.c
> > > > > +++ b/drivers/pci/bus.c
> > > > > @@ -411,6 +411,34 @@ void pci_walk_bus(struct pci_bus *top,
> > > > > int
> > > > > (*cb)(struct pci_dev *, void *),
> > > > >  }
> > > > >  EXPORT_SYMBOL_GPL(pci_walk_bus);
> > > > > 
> > > > > +/** pci_walk_below_dev - walk devices below (or on) another 
> > > > > device
> > > > > + *  @dev      device for which we should walk below,
> > > > > include 
> > > > > device
> > > > > when not a port.
> > > > > + *  @cb       callback to be called for each device found
> > > > > + *  @userdata arbitrary pointer to be passed to callback.
> > > > > + *
> > > > > + *  If the device provided is a port,
> > > > > + *  walk the subordinate bus, including any bridged devices
> > > > > + *  on buses under this bus.  Call the provided callback
> > > > > + *  on each device found.
> > > > > + *
> > > > > + *  If the device provided hs no subordinate bus, call the 
> > > > > provided
> > > > > + *  callback on the device itself.
> > > > > + *
> > > > > + */
> > > > > +void pci_walk_below_dev(struct pci_dev *dev, int
> > > > > (*cb)(struct
> > > > > pci_dev
> > > > > *, void *),
> > > > > +			void *userdata)
> > > > > +{
> > > > > +	struct pci_bus *bus;
> > > > > +
> > > > > +	if (dev->subordinate) {
> > > > > +		bus = dev->subordinate;
> > > > > +		pci_walk_bus(bus, cb, userdata);
> > > > > +	} else {
> > > > > +		cb(dev, userdata);
> > > > > +	}
> > > > > +}
> > > > > +EXPORT_SYMBOL_GPL(pci_walk_below_dev);
> > > > > +
> > > > >  struct pci_bus *pci_bus_get(struct pci_bus *bus)
> > > > >  {
> > > > >  	if (bus)
> > > > > diff --git a/drivers/pci/pcie/err.c b/drivers/pci/pcie/err.c
> > > > > index 14bb8f54723e..fa08b1cc3d96 100644
> > > > > --- a/drivers/pci/pcie/err.c
> > > > > +++ b/drivers/pci/pcie/err.c
> > > > > @@ -151,33 +151,39 @@ pci_ers_result_t
> > > > > pcie_do_recovery(struct
> > > > > pci_dev
> > > > > *dev,
> > > > >  			pci_ers_result_t (*reset_link)(struct
> > > > > pci_dev *pdev))
> > > > >  {
> > > > >  	pci_ers_result_t status = PCI_ERS_RESULT_CAN_RECOVER;
> > > > > -	struct pci_bus *bus;
> > > > > 
> > > > >  	/*
> > > > >  	 * Error recovery runs on all subordinates of the
> > > > > first 
> > > > > downstream
> > > > > port.
> > > > >  	 * If the downstream port detected the error, it is
> > > > > cleared at 
> > > > > the
> > > > > end.
> > > > > +	 * For RCiEPs we should reset just the RCiEP itself.
> > > > >  	 */
> > > > >  	if (!(pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT ||
> > > > > -	      pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM))
> > > > > +	      pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM ||
> > > > > +	      pci_pcie_type(dev) == PCI_EXP_TYPE_RC_END))
> > > > >  		dev = dev->bus->self;
> > > > > -	bus = dev->subordinate;
> > > > > 
> > > > >  	pci_dbg(dev, "broadcast error_detected message\n");
> > > > >  	if (state == pci_channel_io_frozen) {
> > > > > -		pci_walk_bus(bus, report_frozen_detected,
> > > > > &status);
> > > > > +		pci_walk_below_dev(dev, report_frozen_detected,
> > > > > &status);
> > > > > +		if (pci_pcie_type(dev) == PCI_EXP_TYPE_RC_END)
> > > > > {
> > > > > +			pci_warn(dev, "link reset not possible
> > > > > for RCiEP\n");
> > > > > +			status = PCI_ERS_RESULT_NONE;
> > > > > +			goto failed;
> > > > > +		}
> > > > > +
> > > > >  		status = reset_link(dev);
> > > > >  		if (status != PCI_ERS_RESULT_RECOVERED) {
> > > > >  			pci_warn(dev, "link reset failed\n");
> > > > >  			goto failed;
> > > > >  		}
> > > > >  	} else {
> > > > > -		pci_walk_bus(bus, report_normal_detected,
> > > > > &status);
> > > > > +		pci_walk_below_dev(dev, report_normal_detected,
> > > > > &status);
> > > > >  	}
> > > > > 
> > > > >  	if (status == PCI_ERS_RESULT_CAN_RECOVER) {
> > > > >  		status = PCI_ERS_RESULT_RECOVERED;
> > > > >  		pci_dbg(dev, "broadcast mmio_enabled
> > > > > message\n");
> > > > > -		pci_walk_bus(bus, report_mmio_enabled,
> > > > > &status);
> > > > > +		pci_walk_below_dev(dev, report_mmio_enabled,
> > > > > &status);
> > > > >  	}
> > > > > 
> > > > >  	if (status == PCI_ERS_RESULT_NEED_RESET) {
> > > > > @@ -188,17 +194,20 @@ pci_ers_result_t
> > > > > pcie_do_recovery(struct
> > > > > pci_dev
> > > > > *dev,
> > > > >  		 */
> > > > >  		status = PCI_ERS_RESULT_RECOVERED;
> > > > >  		pci_dbg(dev, "broadcast slot_reset message\n");
> > > > > -		pci_walk_bus(bus, report_slot_reset, &status);
> > > > > +		pci_walk_below_dev(dev, report_slot_reset,
> > > > > &status);
> > > > >  	}
> > > > > 
> > > > >  	if (status != PCI_ERS_RESULT_RECOVERED)
> > > > >  		goto failed;
> > > > > 
> > > > >  	pci_dbg(dev, "broadcast resume message\n");
> > > > > -	pci_walk_bus(bus, report_resume, &status);
> > > > > +	pci_walk_below_dev(dev, report_resume, &status);
> > > > > 
> > > > > -	pci_aer_clear_device_status(dev);
> > > > > -	pci_aer_clear_nonfatal_status(dev);
> > > > > +	if ((pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT ||
> > > > > +	     pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM)) {
> > > > > +		pci_aer_clear_device_status(dev);
> > > > > +		pci_aer_clear_nonfatal_status(dev);
> > > > > +	}
> > > > >  	pci_info(dev, "device recovery successful\n");
> > > > >  	return status;
> > > > > 
> > > > > diff --git a/include/linux/pci.h b/include/linux/pci.h
> > > > > index c79d83304e52..538bf0a76d33 100644
> > > > > --- a/include/linux/pci.h
> > > > > +++ b/include/linux/pci.h
> > > > > @@ -1411,6 +1411,8 @@ int pci_scan_bridge(struct pci_bus
> > > > > *bus,
> > > > > struct
> > > > > pci_dev *dev, int max,
> > > > > 
> > > > >  void pci_walk_bus(struct pci_bus *top, int (*cb)(struct
> > > > > pci_dev 
> > > > > *,
> > > > > void *),
> > > > >  		  void *userdata);
> > > > > +void pci_walk_below_dev(struct pci_dev *dev, int
> > > > > (*cb)(struct
> > > > > pci_dev
> > > > > *, void *),
> > > > > +			void *userdata);
> > > > >  int pci_cfg_space_size(struct pci_dev *dev);
> > > > >  unsigned char pci_bus_max_busnr(struct pci_bus *bus);
> > > > >  void pci_setup_bridge(struct pci_bus *bus);
> > > > > -- 
> > > > > 2.19.1




[Index of Archives]     [Linux IBM ACPI]     [Linux Power Management]     [Linux Kernel]     [Linux Laptop]     [Kernel Newbies]     [Share Photos]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux