On Wed, 12 Feb 2020 14:05:40 +0300, Mika Westerberg wrote:
> If the BIOS default timeout for the watchdog is too small userspace may
> not have enough time to configure new timeout after opening the device
> before the system is already reset. For this reason program default
> timeout of 30 seconds in the driver probe and allow userspace to change
> this from command line or through module parameter (wdat_wdt.timeout).
>
> Reported-by: Jean Delvare <jdelvare@xxxxxxx>
> Signed-off-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
> ---
> drivers/watchdog/wdat_wdt.c | 24 ++++++++++++++++++++++++
> 1 file changed, 24 insertions(+)
>
> diff --git a/drivers/watchdog/wdat_wdt.c b/drivers/watchdog/wdat_wdt.c
> index 2132018f031d..7b0257163522 100644
> --- a/drivers/watchdog/wdat_wdt.c
> +++ b/drivers/watchdog/wdat_wdt.c
> @@ -54,6 +54,13 @@ module_param(nowayout, bool, 0);
> MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default="
> __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
>
> +#define WDAT_DEFAULT_TIMEOUT 30
> +
> +static int timeout = WDAT_DEFAULT_TIMEOUT;
> +module_param(timeout, int, 0);
> +MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds (default="
> + __MODULE_STRING(WDAT_DEFAULT_TIMEOUT) ")");
> +
> static int wdat_wdt_read(struct wdat_wdt *wdat,
> const struct wdat_instruction *instr, u32 *value)
> {
> @@ -308,6 +315,7 @@ static int wdat_wdt_probe(struct platform_device *pdev)
> struct device *dev = &pdev->dev;
> const struct acpi_wdat_entry *entries;
> const struct acpi_table_wdat *tbl;
> + int default_timeout = timeout;
> struct wdat_wdt *wdat;
> struct resource *res;
> void __iomem **regs;
> @@ -438,6 +446,22 @@ static int wdat_wdt_probe(struct platform_device *pdev)
>
> platform_set_drvdata(pdev, wdat);
>
> + /*
> + * Set initial timeout so that userspace has time to configure
> + * the watchdog properly after it has opened the device. In some
> + * cases the BIOS default is too short and causes immediate reboot.
> + */
> + default_timeout = timeout;
You have already done that at variable declaration time.
> + if (timeout < wdat->wdd.min_hw_heartbeat_ms ||
> + timeout > wdat->wdd.max_hw_heartbeat_ms)
Comparing seconds to milliseconds is unlikely to give the expected
result.
> + default_timeout = WDAT_DEFAULT_TIMEOUT;
> + else
> + default_timeout = timeout;
You have already done that twice ;-)
> +
> + ret = wdat_wdt_set_timeout(&wdat->wdd, timeout);
You must pass "default_timeout" here, not "timeout", else the check
before serves no purpose. It might be less confusing to not introduce a
separate variable and just tweak timeout in place?
> + if (ret)
> + return ret;
> +
> watchdog_set_nowayout(&wdat->wdd, nowayout);
> return devm_watchdog_register_device(dev, &wdat->wdd);
> }
--
Jean Delvare
SUSE L3 Support
