On 25/06/2019 00:09, Rafael J. Wysocki wrote:
> On Tuesday, June 25, 2019 12:20:26 AM CEST Rafael J. Wysocki wrote:
>> On Mon, Jun 24, 2019 at 11:37 PM Rafael J. Wysocki <rafael@xxxxxxxxxx> wrote:
>>>
>>> On Mon, Jun 24, 2019 at 2:43 PM Jon Hunter <jonathanh@xxxxxxxxxx> wrote:
>>>>
>>>> Hi Rafael,
>>>>
>>>> On 13/06/2019 22:59, Rafael J. Wysocki wrote:
>>>>> From: Rafael J. Wysocki <rafael.j.wysocki@xxxxxxxxx>
>>>>>
>>>>> Commit d491f2b75237 ("PCI: PM: Avoid possible suspend-to-idle issue")
>>>>> attempted to avoid a problem with devices whose drivers want them to
>>>>> stay in D0 over suspend-to-idle and resume, but it did not go as far
>>>>> as it should with that.
>>>>>
>>>>> Namely, first of all, the power state of a PCI bridge with a
>>>>> downstream device in D0 must be D0 (based on the PCI PM spec r1.2,
>>>>> sec 6, table 6-1, if the bridge is not in D0, there can be no PCI
>>>>> transactions on its secondary bus), but that is not actively enforced
>>>>> during system-wide PM transitions, so use the skip_bus_pm flag
>>>>> introduced by commit d491f2b75237 for that.
>>>>>
>>>>> Second, the configuration of devices left in D0 (whatever the reason)
>>>>> during suspend-to-idle need not be changed and attempting to put them
>>>>> into D0 again by force is pointless, so explicitly avoid doing that.
>>>>>
>>>>> Fixes: d491f2b75237 ("PCI: PM: Avoid possible suspend-to-idle issue")
>>>>> Reported-by: Kai-Heng Feng <kai.heng.feng@xxxxxxxxxxxxx>
>>>>> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@xxxxxxxxx>
>>>>> Reviewed-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
>>>>> Tested-by: Kai-Heng Feng <kai.heng.feng@xxxxxxxxxxxxx>
>>>>
>>>> I have noticed a regression in both the mainline and -next branches on
>>>> one of our boards when testing suspend. The bisect is point to this
>>>> commit and reverting on top of mainline does fix the problem. So far I
>>>> have not looked at this in close detail but kernel log is showing ...
>>>
>>> Can you please collect a log like that, but with dynamic debug in
>>> pci-driver.c enabled?
>>>
>>> Note that reverting this commit is rather out of the question, so we
>>> need to get to the bottom of the failure.
>>
>> I suspect that there is a problem with the pm_suspend_via_firmware()
>> check which returns 'false' on the affected board, but the platform
>> actually removes power from devices left in D0 during suspend.
>>
>> I guess it would be more appropriate to check something like
>> pm_suspend_no_platform() which would return 'true' in the
>> suspend-to-idle patch w/ ACPI.
>
> So I wonder if the patch below makes any difference?
>
> ---
> drivers/pci/pci-driver.c | 8 ++++----
> include/linux/suspend.h | 26 ++++++++++++++++++++++++--
> kernel/power/suspend.c | 3 +++
> 3 files changed, 31 insertions(+), 6 deletions(-)
>
> Index: linux-pm/include/linux/suspend.h
> ===================================================================
> --- linux-pm.orig/include/linux/suspend.h
> +++ linux-pm/include/linux/suspend.h
> @@ -209,8 +209,9 @@ extern int suspend_valid_only_mem(suspen
>
> extern unsigned int pm_suspend_global_flags;
>
> -#define PM_SUSPEND_FLAG_FW_SUSPEND (1 << 0)
> -#define PM_SUSPEND_FLAG_FW_RESUME (1 << 1)
> +#define PM_SUSPEND_FLAG_FW_SUSPEND BIT(0)
> +#define PM_SUSPEND_FLAG_FW_RESUME BIT(1)
> +#define PM_SUSPEND_FLAG_NO_PLATFORM BIT(2)
>
> static inline void pm_suspend_clear_flags(void)
> {
> @@ -227,6 +228,11 @@ static inline void pm_set_resume_via_fir
> pm_suspend_global_flags |= PM_SUSPEND_FLAG_FW_RESUME;
> }
>
> +static inline void pm_set_suspend_no_platform(void)
> +{
> + pm_suspend_global_flags |= PM_SUSPEND_FLAG_NO_PLATFORM;
> +}
> +
> /**
> * pm_suspend_via_firmware - Check if platform firmware will suspend the system.
> *
> @@ -268,6 +274,22 @@ static inline bool pm_resume_via_firmwar
> return !!(pm_suspend_global_flags & PM_SUSPEND_FLAG_FW_RESUME);
> }
>
> +/**
> + * pm_suspend_no_platform - Check if platform may change device power states.
> + *
> + * To be called during system-wide power management transitions to sleep states
> + * or during the subsequent system-wide transitions back to the working state.
> + *
> + * Return 'true' if the power states of devices remain under full control of the
> + * kernel throughout the system-wide suspend and resume cycle in progress (that
> + * is, if a device is put into a certain power state during suspend, it can be
> + * expected to remain in that state during resume).
> + */
> +static inline bool pm_suspend_no_platform(void)
> +{
> + return !!(pm_suspend_global_flags & PM_SUSPEND_FLAG_NO_PLATFORM);
> +}
> +
> /* Suspend-to-idle state machnine. */
> enum s2idle_states {
> S2IDLE_STATE_NONE, /* Not suspended/suspending. */
> Index: linux-pm/kernel/power/suspend.c
> ===================================================================
> --- linux-pm.orig/kernel/power/suspend.c
> +++ linux-pm/kernel/power/suspend.c
> @@ -493,6 +493,9 @@ int suspend_devices_and_enter(suspend_st
>
> pm_suspend_target_state = state;
>
> + if (state == PM_SUSPEND_TO_IDLE)
> + pm_set_suspend_no_platform();
> +
> error = platform_suspend_begin(state);
> if (error)
> goto Close;
> Index: linux-pm/drivers/pci/pci-driver.c
> ===================================================================
> --- linux-pm.orig/drivers/pci/pci-driver.c
> +++ linux-pm/drivers/pci/pci-driver.c
> @@ -870,7 +870,7 @@ static int pci_pm_suspend_noirq(struct d
> pci_dev->bus->self->skip_bus_pm = true;
> }
>
> - if (pci_dev->skip_bus_pm && !pm_suspend_via_firmware()) {
> + if (pci_dev->skip_bus_pm && pm_suspend_no_platform()) {
> dev_dbg(dev, "PCI PM: Skipped\n");
> goto Fixup;
> }
> @@ -925,10 +925,10 @@ static int pci_pm_resume_noirq(struct de
> /*
> * In the suspend-to-idle case, devices left in D0 during suspend will
> * stay in D0, so it is not necessary to restore or update their
> - * configuration here and attempting to put them into D0 again may
> - * confuse some firmware, so avoid doing that.
> + * configuration here and attempting to put them into D0 again is
> + * pointless, so avoid doing that.
> */
> - if (!pci_dev->skip_bus_pm || pm_suspend_via_firmware())
> + if (!(pci_dev->skip_bus_pm && pm_suspend_no_platform()))
> pci_pm_default_resume_early(pci_dev);
>
> pci_fixup_device(pci_fixup_resume_early, pci_dev);
I can confirm that above works for me. So ...
Tested-by: Jon Hunter <jonathanh@xxxxxxxxxx>
This looks better ...
[ 52.545820] PM: suspend entry (deep)
[ 52.549547] Filesystems sync: 0.000 seconds
[ 52.553966] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 52.562375] OOM killer disabled.
[ 52.565684] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 52.574426] printk: Suspending console(s) (use no_console_suspend to debug)
[ 52.590255] r8169 0000:01:00.0 eth0: Link is Down
[ 52.590483] pci_generic_config_write32: 22 callbacks suppressed
[ 52.590488] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x9c may corrupt adjacent RW1C bits
[ 52.794091] r8169 0000:01:00.0: PCI PM: Suspend power state: D3hot
[ 52.794128] pcieport 0000:00:02.0: PCI PM: Suspend power state: D0
[ 52.805674] Disabling non-boot CPUs ...
[ 52.809257] Entering suspend state LP1
[ 52.809284] Enabling non-boot CPUs ...
[ 52.810184] CPU1 is up
[ 52.810973] CPU2 is up
[ 52.811819] CPU3 is up
[ 52.822259] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes
[ 52.840085] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4c may corrupt adjacent RW1C bits
[ 52.840096] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x88 may corrupt adjacent RW1C bits
[ 52.840101] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x90 may corrupt adjacent RW1C bits
[ 52.840106] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x98 may corrupt adjacent RW1C bits
[ 52.840111] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x9c may corrupt adjacent RW1C bits
[ 52.840116] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0xa8 may corrupt adjacent RW1C bits
[ 52.840121] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0xb0 may corrupt adjacent RW1C bits
[ 52.840155] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits
[ 52.840160] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x52 may corrupt adjacent RW1C bits
[ 52.840184] pcieport 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge
[ 52.864252] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000004
[ 53.024171] r8169 0000:01:00.0 eth0: Link is Down
[ 53.376438] ata1: SATA link down (SStatus 0 SControl 300)
[ 55.881131] r8169 0000:01:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 56.012154] OOM killer enabled.
[ 56.015295] Restarting tasks ... done.
[ 56.019415] PM: suspend exit
[ 56.045929] PM: suspend entry (deep)
[ 56.049565] Filesystems sync: 0.000 seconds
[ 56.053906] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 56.062205] OOM killer disabled.
[ 56.065462] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 56.074193] printk: Suspending console(s) (use no_console_suspend to debug)
[ 56.096375] r8169 0000:01:00.0 eth0: Link is Down
[ 56.304070] r8169 0000:01:00.0: PCI PM: Suspend power state: D3hot
[ 56.304111] pcieport 0000:00:02.0: PCI PM: Suspend power state: D0
[ 56.314134] tegra-pcie 1003000.pcie: PME Ack is not received on port: 1
[ 56.325777] Disabling non-boot CPUs ...
[ 56.328540] Entering suspend state LP1
[ 56.328571] Enabling non-boot CPUs ...
[ 56.329687] CPU1 is up
[ 56.330694] CPU2 is up
[ 56.331772] CPU3 is up
[ 56.332396] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes
[ 56.350134] pcieport 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge
[ 56.374241] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000004
[ 56.534158] r8169 0000:01:00.0 eth0: Link is Down
[ 56.886516] ata1: SATA link down (SStatus 0 SControl 300)
[ 59.417895] OOM killer enabled.
[ 59.421025] Restarting tasks ... done.
[ 59.425305] PM: suspend exit
[ 60.756040] r8169 0000:01:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Thanks!
Jon
--
nvpublic
