On Wed, Jun 5, 2019 at 4:58 PM Mika Westerberg
<mika.westerberg@xxxxxxxxxxxxxxx> wrote:
>
> Currently Linux does not follow PCIe spec regarding the required delays
> after reset. A concrete example is a Thunderbolt add-in-card that
> consists of a PCIe switch and two PCIe endpoints:
>
> +-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
> +-01.0-[04-36]-- DS hotplug port
> +-02.0-[37]----00.0 xHCI controller
> \-04.0-[38-6b]-- DS hotplug port
>
> The root port (1b.0) and the PCIe switch downstream ports are all PCIe
> gen3 so they support 8GT/s link speeds.
>
> We wait for the PCIe hierarchy to enter D3cold (runtime):
>
> pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
>
> When it wakes up from D3cold, according to the PCIe 4.0 section 5.8 the
> PCIe switch is put to reset and its power is re-applied. This means that
> we must follow the rules in PCIe 4.0 section 6.6.1.
>
> For the PCIe gen3 ports we are dealing with here, the following applies:
>
> With a Downstream Port that supports Link speeds greater than 5.0
> GT/s, software must wait a minimum of 100 ms after Link training
> completes before sending a Configuration Request to the device
> immediately below that Port. Software can determine when Link training
> completes by polling the Data Link Layer Link Active bit or by setting
> up an associated interrupt (see Section 6.7.3.3).
>
> Translating this into the above topology we would need to do this (DLLLA
> stands for Data Link Layer Link Active):
>
> pcieport 0000:00:1b.0: wait for 100ms after DLLLA is set before access to 0000:01:00.0
> pcieport 0000:02:00.0: wait for 100ms after DLLLA is set before access to 0000:03:00.0
> pcieport 0000:02:02.0: wait for 100ms after DLLLA is set before access to 0000:37:00.0
>
> I've instrumented the kernel with additional logging so we can see the
> actual delays the kernel performs:
>
> pcieport 0000:00:1b.0: power state changed by ACPI to D0
> pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
> pcieport 0000:00:1b.0: waking up bus
> pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
> pcieport 0000:00:1b.0: restoring config space at offset 0x2c (was 0x60, writing 0x60)
> ...
> pcieport 0000:00:1b.0: PME# disabled
> pcieport 0000:01:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
> ...
> pcieport 0000:01:00.0: PME# disabled
> pcieport 0000:02:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
> ...
> pcieport 0000:02:00.0: PME# disabled
> pcieport 0000:02:01.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
> ...
> pcieport 0000:02:01.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
> pcieport 0000:02:01.0: PME# disabled
> pcieport 0000:02:02.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
> ...
> pcieport 0000:02:02.0: PME# disabled
> pcieport 0000:02:04.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
> ...
> pcieport 0000:02:04.0: PME# disabled
> pcieport 0000:02:01.0: PME# enabled
> pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
> pcieport 0000:02:04.0: PME# enabled
> pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
> thunderbolt 0000:03:00.0: restoring config space at offset 0x14 (was 0x0, writing 0x8a040000)
> ...
> thunderbolt 0000:03:00.0: PME# disabled
> xhci_hcd 0000:37:00.0: restoring config space at offset 0x10 (was 0x0, writing 0x73f00000)
> ...
> xhci_hcd 0000:37:00.0: PME# disabled
>
> For the switch upstream port (01:00.0) we wait for 100ms but not taking
> into account the DLLLA requirement. We then wait 10ms for D3hot -> D0
> transition of the root port and the two downstream hotplug ports. This
> means that we deviate from what the spec requires.
>
> Performing the same check for system sleep (s2idle) transitions we can
> see following when resuming from s2idle:
>
> pcieport 0000:00:1b.0: power state changed by ACPI to D0
> pcieport 0000:00:1b.0: restoring config space at offset 0x2c (was 0x60, writing 0x60)
> ...
> pcieport 0000:01:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
> ...
> pcieport 0000:02:02.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
> pcieport 0000:02:02.0: restoring config space at offset 0x2c (was 0x0, writing 0x0)
> pcieport 0000:02:01.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
> pcieport 0000:02:04.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
> pcieport 0000:02:02.0: restoring config space at offset 0x28 (was 0x0, writing 0x0)
> pcieport 0000:02:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
> pcieport 0000:02:02.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1fff1)
> pcieport 0000:02:01.0: restoring config space at offset 0x2c (was 0x0, writing 0x60)
> pcieport 0000:02:02.0: restoring config space at offset 0x20 (was 0x0, writing 0x73f073f0)
> pcieport 0000:02:04.0: restoring config space at offset 0x2c (was 0x0, writing 0x60)
> pcieport 0000:02:01.0: restoring config space at offset 0x28 (was 0x0, writing 0x60)
> pcieport 0000:02:00.0: restoring config space at offset 0x2c (was 0x0, writing 0x0)
> pcieport 0000:02:02.0: restoring config space at offset 0x1c (was 0x101, writing 0x1f1)
> pcieport 0000:02:04.0: restoring config space at offset 0x28 (was 0x0, writing 0x60)
> pcieport 0000:02:01.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1ff10001)
> pcieport 0000:02:00.0: restoring config space at offset 0x28 (was 0x0, writing 0x0)
> pcieport 0000:02:02.0: restoring config space at offset 0x18 (was 0x0, writing 0x373702)
> pcieport 0000:02:04.0: restoring config space at offset 0x24 (was 0x10001, writing 0x49f12001)
> pcieport 0000:02:01.0: restoring config space at offset 0x20 (was 0x0, writing 0x73e05c00)
> pcieport 0000:02:00.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1fff1)
> pcieport 0000:02:04.0: restoring config space at offset 0x20 (was 0x0, writing 0x89f07400)
> pcieport 0000:02:01.0: restoring config space at offset 0x1c (was 0x101, writing 0x5151)
> pcieport 0000:02:00.0: restoring config space at offset 0x20 (was 0x0, writing 0x8a008a00)
> pcieport 0000:02:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
> pcieport 0000:02:04.0: restoring config space at offset 0x1c (was 0x101, writing 0x6161)
> pcieport 0000:02:01.0: restoring config space at offset 0x18 (was 0x0, writing 0x360402)
> pcieport 0000:02:00.0: restoring config space at offset 0x1c (was 0x101, writing 0x1f1)
> pcieport 0000:02:04.0: restoring config space at offset 0x18 (was 0x0, writing 0x6b3802)
> pcieport 0000:02:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
> pcieport 0000:02:00.0: restoring config space at offset 0x18 (was 0x0, writing 0x30302)
> pcieport 0000:02:01.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
> pcieport 0000:02:04.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
> pcieport 0000:02:00.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
> pcieport 0000:02:01.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
> pcieport 0000:02:04.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
> pcieport 0000:02:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
> xhci_hcd 0000:37:00.0: restoring config space at offset 0x10 (was 0x0, writing 0x73f00000)
> ...
> thunderbolt 0000:03:00.0: restoring config space at offset 0x14 (was 0x0, writing 0x8a040000)
>
> This is even worse. None of the mandatory delays are performed. If this
> would be S3 instead of s2idle then according to PCI FW spec 3.2 section
> 4.6.8. there is a specific _DSM that allows the OS to skip the delays
> but this platform does not provide the _DSM and does not go to S3 anyway
> so no firmware is involved that could already handle these delays.
>
> In this particular Intel Coffee Lake platform these delays are not
> actually needed because there is an additional delay as part of the ACPI
> power resource that is used to turn on power to the hierarchy but since
> that additional delay is not required by any of standards (PCIe, ACPI)
> it is not present in the Intel Ice Lake, for example where missing the
> mandatory delays causes pciehp to start tearing down the stack too early
> (links are not yet trained).
>
> For this reason, change the PCIe portdrv PM resume hooks so that they
> perform the mandatory delays before the downstream component gets
> resumed. We perform the delays before port services are resumed because
> otherwise pciehp might find that the link is not up (even if it is just
> training) and tears-down the hierarchy.
>
> Signed-off-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
Generally
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@xxxxxxxxx>
with a couple of nits below.
> ---
> drivers/pci/pci.c | 29 +++++++++------
> drivers/pci/pci.h | 1 +
> drivers/pci/pcie/portdrv_core.c | 62 +++++++++++++++++++++++++++++++++
> 3 files changed, 82 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
> index 8abc843b1615..87a1f902fa8e 100644
> --- a/drivers/pci/pci.c
> +++ b/drivers/pci/pci.c
> @@ -1004,15 +1004,10 @@ static void __pci_start_power_transition(struct pci_dev *dev, pci_power_t state)
> if (state == PCI_D0) {
> pci_platform_power_transition(dev, PCI_D0);
> /*
> - * Mandatory power management transition delays, see
> - * PCI Express Base Specification Revision 2.0 Section
> - * 6.6.1: Conventional Reset. Do not delay for
> - * devices powered on/off by corresponding bridge,
> - * because have already delayed for the bridge.
> + * Mandatory power management transition delays are
> + * handled in the PCIe portdrv resume hooks.
> */
> if (dev->runtime_d3cold) {
> - if (dev->d3cold_delay && !dev->imm_ready)
> - msleep(dev->d3cold_delay);
> /*
> * When powering on a bridge from D3cold, the
> * whole hierarchy may be powered on into
> @@ -4568,14 +4563,16 @@ static int pci_pm_reset(struct pci_dev *dev, int probe)
>
> return pci_dev_wait(dev, "PM D3->D0", PCIE_RESET_READY_POLL_MS);
> }
> +
> /**
> - * pcie_wait_for_link - Wait until link is active or inactive
> + * pcie_wait_for_link_delay - Wait until link is active or inactive
> * @pdev: Bridge device
> * @active: waiting for active or inactive?
> + * @delay: Delay to wait after link has become active (in ms)
> *
> * Use this to wait till link becomes active or inactive.
> */
> -bool pcie_wait_for_link(struct pci_dev *pdev, bool active)
> +bool pcie_wait_for_link_delay(struct pci_dev *pdev, bool active, int delay)
> {
> int timeout = 1000;
> bool ret;
> @@ -4612,13 +4609,25 @@ bool pcie_wait_for_link(struct pci_dev *pdev, bool active)
> timeout -= 10;
> }
> if (active && ret)
> - msleep(100);
> + msleep(delay);
> else if (ret != active)
> pci_info(pdev, "Data Link Layer Link Active not %s in 1000 msec\n",
> active ? "set" : "cleared");
> return ret == active;
> }
>
> +/**
> + * pcie_wait_for_link - Wait until link is active or inactive
> + * @pdev: Bridge device
> + * @active: waiting for active or inactive?
> + *
> + * Use this to wait till link becomes active or inactive.
> + */
> +bool pcie_wait_for_link(struct pci_dev *pdev, bool active)
> +{
> + return pcie_wait_for_link_delay(pdev, active, 100);
> +}
> +
> void pci_reset_secondary_bus(struct pci_dev *dev)
> {
> u16 ctrl;
> diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
> index 9cb99380c61e..59802b3def4b 100644
> --- a/drivers/pci/pci.h
> +++ b/drivers/pci/pci.h
> @@ -493,6 +493,7 @@ static inline int pci_dev_specific_disable_acs_redir(struct pci_dev *dev)
> void pcie_do_recovery(struct pci_dev *dev, enum pci_channel_state state,
> u32 service);
>
> +bool pcie_wait_for_link_delay(struct pci_dev *pdev, bool active, int delay);
> bool pcie_wait_for_link(struct pci_dev *pdev, bool active);
> #ifdef CONFIG_PCIEASPM
> void pcie_aspm_init_link_state(struct pci_dev *pdev);
> diff --git a/drivers/pci/pcie/portdrv_core.c b/drivers/pci/pcie/portdrv_core.c
> index 1b330129089f..88d151a54be6 100644
> --- a/drivers/pci/pcie/portdrv_core.c
> +++ b/drivers/pci/pcie/portdrv_core.c
> @@ -9,6 +9,7 @@
> #include <linux/module.h>
> #include <linux/pci.h>
> #include <linux/kernel.h>
> +#include <linux/delay.h>
> #include <linux/errno.h>
> #include <linux/pm.h>
> #include <linux/pm_runtime.h>
> @@ -378,6 +379,58 @@ static int pm_iter(struct device *dev, void *data)
> return 0;
> }
>
> +static int get_downstream_delay(struct pci_bus *bus)
> +{
> + struct pci_dev *pdev;
> + int min_delay = 100;
> + int max_delay = 0;
> +
> + list_for_each_entry(pdev, &bus->devices, bus_list) {
> + if (!pdev->imm_ready)
> + min_delay = 0;
> + else if (pdev->d3cold_delay < min_delay)
> + min_delay = pdev->d3cold_delay;
> + if (pdev->d3cold_delay > max_delay)
> + max_delay = pdev->d3cold_delay;
> + }
> +
> + return max(min_delay, max_delay);
> +}
> +
> +static void wait_for_downstream_link(struct pci_dev *pdev)
> +{
> + /*
> + * Handle delays according to PCIe 4.0 section 6.6.1 before
> + * configuration access to the downstream component is permitted.
> + *
> + * This blocks PCI core resume of the hierarchy below this port
> + * until the link is trained.
> + */
Shouldn't the above go to a kerneldoc comment?
> + if ((pci_pcie_type(pdev) == PCI_EXP_TYPE_ROOT_PORT ||
> + pci_pcie_type(pdev) == PCI_EXP_TYPE_DOWNSTREAM) &&
> + pdev->subordinate && !list_empty(&pdev->subordinate->devices) &&
> + pdev->bridge_d3 && !pci_dev_is_disconnected(pdev)) {
There's nothing except for this if () in the function, so maybe just
return here if the condition is not satisfied?
Also maybe split it into a port type check (you can return right away
if it fails), disconnected check and the rest?
> + int delay;
> +
> + delay = get_downstream_delay(pdev->subordinate);
> + if (!delay)
> + return;
> +
> + dev_dbg(&pdev->dev, "waiting downstream link for %d ms\n", delay);
> +
> + /*
> + * If downstream port does not support speeds greater than
> + * 5 GT/s need to wait 100ms. For higher speeds (gen3) we
> + * need to wait first for the data link layer to become
> + * active.
> + */
> + if (pcie_get_speed_cap(pdev) <= PCIE_SPEED_5_0GT)
> + msleep(delay);
> + else
> + pcie_wait_for_link_delay(pdev, true, delay);
> + }
> +}
> +
> /**
> * pcie_port_device_suspend - suspend port services associated with a PCIe port
> * @dev: PCI Express port to handle
> @@ -391,6 +444,13 @@ int pcie_port_device_suspend(struct device *dev)
> int pcie_port_device_resume_noirq(struct device *dev)
> {
> size_t off = offsetof(struct pcie_port_service_driver, resume_noirq);
> +
> + /*
> + * Wait for the link to be fully up before resuming port services.
> + * This prevents pciehp from starting to tear-down the hierarchy
> + * too soon.
> + */
> + wait_for_downstream_link(to_pci_dev(dev));
> return device_for_each_child(dev, &off, pm_iter);
> }
>
> @@ -421,6 +481,8 @@ int pcie_port_device_runtime_suspend(struct device *dev)
> int pcie_port_device_runtime_resume(struct device *dev)
> {
> size_t off = offsetof(struct pcie_port_service_driver, runtime_resume);
> +
The comment from pcie_port_device_resume_noirq() is applicable here
too, so maybe move it to a common place (kerneldoc?).
> + wait_for_downstream_link(to_pci_dev(dev));
> return device_for_each_child(dev, &off, pm_iter);
> }
> #endif /* PM */
> --
> 2.20.1
>
