Hi Enric, On Wed, Jul 04, 2018 at 12:36:39PM +0200, Enric Balletbo i Serra wrote: > Hi Matthias, > > Sorry for late reply, my memory is bad so I need to look at this again. The > patch was send some time ago and there are pending changes to do but then I > switched. I'll take a look, but did you saw why this patch was not merged [1]? > Maybe that could answer some of your questions. > > Best regards, > Enric > > [1] https://lkml.org/lkml/2018/2/27/910 I missed this, thanks for the pointer! > On 03/07/18 19:13, Matthias Kaehlcke wrote: > > On Thu, Jun 28, 2018 at 05:33:02PM -0700, Matthias Kaehlcke wrote: > >> Hi, > >> > >> I stumbled across this patch since I'm currently poking around with > >> early thermal bringup on a platform and this patch has been integrated > >> in our development tree. > >> > >> I'm seeing some unexpected behaviors, which could entirely due to > >> wrong expectation from my side. I only have some basic working > >> knowledge of the thermal framework, just want to double check and > >> perhaps learn a thing or two. > >> > >> On Mon, Feb 26, 2018 at 03:41:18PM +0100, Enric Balletbo i Serra wrote: > >>> From: Zhang Rui <rui.zhang@xxxxxxxxx> > >>> > >>> Thermal "mode" sysfs attribute is introduced to enable/disable a thermal > >>> zone, and .get_mode()/.set_mode() callback is introduced for platform > >>> thermal driver to enable/disable the hardware thermal control logic. And > >>> thermal core takes no action upon thermal zone enable/disable. > >>> > >>> Actually, this is not quite right because thermal core still pokes those > >>> disabled thermal zones occasionally, e.g. upon system resume. > >>> > >>> To fix this, a new flag 'mode' is introduced in struct thermal_zone_device > >>> to represent the thermal zone mode, and several decisions have been made > >>> based on this flag, including > >>> 1. check the thermal zone mode right after it's registered. > >>> 2. skip updating thermal zone if the zone is disabled > >>> 3. stop the polling timer when the thermal zone is disabled > >>> > >>> Note: basically, this patch doesn't affect the existing always-enabled > >>> thermal zones much, with just one exception - > >>> thermal zone .get_mode() must be well prepared to reflect the real thermal > >>> zone status upon the thermal zone registration. > >> > >> From my perspective this looks like a pretty significant change. For > >> the platform I'm working on I added a thermal zone to the device tree, > >> with the expectation that it would be enabled. Judging from the code > >> without this patch this expectation seems to be naive, since > >> of-thermal.c sets tz->mode to THERMAL_DEVICE_DISABLED, so apparently > >> either userspace or some driver should call _set_mode(tz, > >> THERMAL_DEVICE_ENABLED). However even without this the thermal zone > >> appears to be active (I didn't really test end-to-end yet, but at > >> least thermal_zone_device_update() is called and calls > >> handle_thermal_trip()). Not sure why this is the case with > >> THERMAL_DEVICE_DISABLED, but before I learned about the existence of > >> the flag my expectation was that the zone would be enabled. > >> > >> With this patch thermal_zone_device_update() is skipped if the zone > >> hasn't been explictly enabled, which may be consistent with the state > >> of 'tz->mode', but effectively changes the previous/current behavior. > >> > >> Not sure if I'm just dumbly overlooking something obvious or if there > >> is an actual problem with of_thermal (and maybe others). > > > > The problem is that there are now two 'mode' fields, tzd->mode and the > > other typically tzd->devdata->mode, and tzd->mode is never set to enabled. > > > >> thermal zone .get_mode() must be well prepared to reflect the real thermal > >> zone status upon the thermal zone registration. > > > > For of_thermal tzd->mode is initialized with the result of .get_mode() > > when the zone is registered. At this time no sensor has been added > > to the zone, hence the zone is disabled. When a sensor is added later > > tzd->devdata->mode is set to enabled, however tzd->mode remains disabled: > > > > tzd->mode = DISABLED > > tzd->devdata->mode = DISABLED > > > > of_parse_thermal_zones > > thermal_zone_device_register > > tzd->mode = tzd->get_mode() // => DISABLED > > > > <sensor>_probe > > thermal_zone_of_sensor_register > > tzd->set_mode(THERMAL_DEVICE_ENABLED) > > tzd->devdata->mode = ENABLED > > > > One way to fix this for of_thermal could be to setting tzd->mode in > > .set_mode() in addition to setting tzd->devdata->mode. However this > > feels like a workaround/hack. Personally I find it confusing to have > > two mode fields for a thermal zone device. Maybe tzd->mode should > > replace tzd->devdata->mode? > > -- To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
