Re: [PATCH] acpi: pci: don't ignore function ID of bridge device in _PRT

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



> On 8 Apr 2017, at 14:22, Lorenzo Pieralisi <lorenzo.pieralisi@xxxxxxx> wrote:
> 
>> On Sat, Apr 08, 2017 at 12:22:15PM +0100, Ard Biesheuvel wrote:
>>> On 7 April 2017 at 19:35, Ard Biesheuvel <ard.biesheuvel@xxxxxxxxxx> wrote:
>>>> On 7 April 2017 at 19:06, Lorenzo Pieralisi <lorenzo.pieralisi@xxxxxxx> wrote:
>>>>> On Fri, Apr 07, 2017 at 06:12:05PM +0100, Ard Biesheuvel wrote:
>>>>>> On 7 April 2017 at 18:06, Bjorn Helgaas <helgaas@xxxxxxxxxx> wrote:
>>> [...]
>>> 
>>> OK, I have changed my DSDT as follows:
>>> 
>>> 
>>> Device (PCI0)
>>> {
>>>    Name (_ADR, 0x00)
>>>    Name (_HID, "PNP0A08" /* PCI Express Bus */)  // _HID: Hardware ID
>>>    Name (_CID, "PNP0A03" /* PCI Bus */)  // _CID: Compatible ID
>>>    Name (_SEG, 0x00)  // _SEG: PCI Segment
>>>    Name (_BBN, 0x00)  // _BBN: BIOS Bus Number
>>>    Name (_CCA, 0x01)  // _CCA: Cache Coherency Attribute
>>> 
>>>    Device (EXP1)
>>>    {
>>>        Name (_ADR, 0x20001)  // _ADR: Address
>>>        Name (_PRT, Package ()  // _PRT: PCI Routing Table
>>>        {
>>>            // slot 1: dev 2 fn 1
>>>            Package () { 0xFFFF, 0x0, 0x0, 0x140 },
>>>            Package () { 0xFFFF, 0x1, 0x0, 0x141 },
>>>            Package () { 0xFFFF, 0x2, 0x0, 0x142 },
>>>            Package () { 0xFFFF, 0x3, 0x0, 0x143 }
>>>        }) // _PRT
>>>    }
>>>    Device (EXP2)
>>>    {
>>>        Name (_ADR, 0x20002)  // _ADR: Address
>>>        Name (_PRT, Package ()  // _PRT: PCI Routing Table
>>>        {
>>>            // slot 2: dev 2 fn 2
>>>            Package () { 0xFFFF, 0x0, 0x0, 0x144 },
>>>            Package () { 0xFFFF, 0x1, 0x0, 0x145 },
>>>            Package () { 0xFFFF, 0x2, 0x0, 0x146 },
>>>            Package () { 0xFFFF, 0x3, 0x0, 0x147 }
>>>        }) // _PRT
>>>    }
>>>    Device (EXP3)
>>>    {
>>>        Name (_ADR, 0x20003)  // _ADR: Address
>>>        Name (_PRT, Package ()  // _PRT: PCI Routing Table
>>>        {
>>>            // slot 3: dev 2 fn 3
>>>            Package () { 0xFFFF, 0x0, 0x0, 0x148 },
>>>            Package () { 0xFFFF, 0x1, 0x0, 0x149 },
>>>            Package () { 0xFFFF, 0x2, 0x0, 0x14a },
>>>            Package () { 0xFFFF, 0x3, 0x0, 0x14b }
>>>        }) // _PRT
>>>    }
>>> 
>>> but it does not get picked up, and I am back to
>>> 
>>> [    3.357555] pcieport 0000:00:02.2: can't derive routing for PCI INT A
>>> [    3.370477] pcieport 0000:00:02.2: PCI INT A: no GSI
>>> [    3.380549] pcieport 0000:00:02.3: can't derive routing for PCI INT A
>>> [    3.393476] pcieport 0000:00:02.3: PCI INT A: no GSI
>>> 
>> 
>> OK, this does appear to work in fact, for the devices behind the
>> bridges. These messages are from the pcieport driver trying to request
>> an IRQ for the bridge device itself, which no longer works now that
>> the _PRT methods have been moved out.
>> 
>> So that mostly solves the problem. I'll try adding back a _PRT in the
>> PCI root device itself, but i'm not sure if I can make any inferences
>> about the IRQ wiring from the data i have.
> 
> Yes and IIUC with the $SUBJECT patch applied, the endpoints would match
> the _PRT entry under PNP0A08 through their bridge (PCIe port device = 2
> fn = X) device entry, not their own (device = 0) (ie first look-up in
> acpi_pci_irq_lookup() through acpi_pci_irq_find_prt_entry() should fail
> for the endpoints, then the same look-up is carried out with the bridge
> device instead and that succeeds, the _PRT entry routes IRQs for the
> PCIeport AND their downstream endpoint with $SUBJECT patch applied).
> 
> If you add the _PRT under the PCIe port itself (table above) the PCIe
> port can't find an ACPI parent device to route its own IRQx, that's my
> reading of what's going on, I will debug it next week.
> 

This is my understanding as well, and i think there remains little to debug on the kernel side.

Moving the three banks of legacy interrupts to separate companion devices is the correct thing to do, and works as expected for the devices behind the bridge.

The only thing that is lacking now is a _PRT description in the pci root that describes how INTA is wired for the bridges themselves. I am not sure how this matters, and whether this pci h/w ever asserts that interrupt in the first place, so i am just going to map it to 0x140 for now until someone tells me otherwise.


--
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux IBM ACPI]     [Linux Power Management]     [Linux Kernel]     [Linux Laptop]     [Kernel Newbies]     [Share Photos]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux