From: Rafael J. Wysocki <rafael.j.wysocki@xxxxxxxxx>
Modify the ACPI system sleep support setup code to select
suspend-to-idle as the default system sleep state if the
ACPI_FADT_LOW_POWER_S0 flag is set in the FADT and the
default sleep state was not selected from the kernel command
line.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@xxxxxxxxx>
---
Documentation/power/states.txt | 4 +++-
drivers/acpi/sleep.c | 8 ++++++++
include/linux/suspend.h | 2 ++
kernel/power/suspend.c | 4 ++--
4 files changed, 15 insertions(+), 3 deletions(-)
Index: linux-pm/include/linux/suspend.h
===================================================================
--- linux-pm.orig/include/linux/suspend.h
+++ linux-pm/include/linux/suspend.h
@@ -194,6 +194,8 @@ struct platform_freeze_ops {
};
#ifdef CONFIG_SUSPEND
+extern suspend_state_t mem_sleep_default;
+
/**
* suspend_set_ops - set platform dependent suspend operations
* @ops: The new suspend operations to set.
Index: linux-pm/drivers/acpi/sleep.c
===================================================================
--- linux-pm.orig/drivers/acpi/sleep.c
+++ linux-pm/drivers/acpi/sleep.c
@@ -691,6 +691,14 @@ static void acpi_sleep_suspend_setup(voi
if (acpi_sleep_state_supported(i))
sleep_states[i] = 1;
+ /*
+ * Use suspend-to-idle by default if ACPI_FADT_LOW_POWER_S0 is set and
+ * the default suspend mode was not selected from the command line.
+ */
+ if (acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0 &&
+ mem_sleep_default > PM_SUSPEND_MEM)
+ mem_sleep_default = PM_SUSPEND_FREEZE;
+
suspend_set_ops(old_suspend_ordering ?
&acpi_suspend_ops_old : &acpi_suspend_ops);
freeze_set_ops(&acpi_freeze_ops);
Index: linux-pm/kernel/power/suspend.c
===================================================================
--- linux-pm.orig/kernel/power/suspend.c
+++ linux-pm/kernel/power/suspend.c
@@ -44,7 +44,7 @@ const char * const mem_sleep_labels[] =
const char *mem_sleep_states[PM_SUSPEND_MAX];
suspend_state_t mem_sleep_current = PM_SUSPEND_FREEZE;
-static suspend_state_t mem_sleep_default = PM_SUSPEND_MEM;
+suspend_state_t mem_sleep_default = PM_SUSPEND_MAX;
unsigned int pm_suspend_global_flags;
EXPORT_SYMBOL_GPL(pm_suspend_global_flags);
@@ -163,7 +163,7 @@ void suspend_set_ops(const struct platfo
}
if (valid_state(PM_SUSPEND_MEM)) {
mem_sleep_states[PM_SUSPEND_MEM] = mem_sleep_labels[PM_SUSPEND_MEM];
- if (mem_sleep_default == PM_SUSPEND_MEM)
+ if (mem_sleep_default >= PM_SUSPEND_MEM)
mem_sleep_current = PM_SUSPEND_MEM;
}
Index: linux-pm/Documentation/power/states.txt
===================================================================
--- linux-pm.orig/Documentation/power/states.txt
+++ linux-pm/Documentation/power/states.txt
@@ -35,7 +35,9 @@ only one way to cause the system to go i
The default suspend mode (ie. the one to be used without writing anything into
/sys/power/mem_sleep) is either "deep" (if Suspend-To-RAM is supported) or
"s2idle", but it can be overridden by the value of the "mem_sleep_default"
-parameter in the kernel command line.
+parameter in the kernel command line. On some ACPI-based systems, depending on
+the information in the FADT, the default may be "s2idle" even if Suspend-To-RAM
+is supported.
The properties of all of the sleep states are described below.
--
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
