On Tue, Feb 16, 2016 at 01:47:15PM -0500, Ashwin Chaugule wrote:
> Hi Alexey,
>
> On 15 February 2016 at 11:37, Alexey Klimov <alexey.klimov@xxxxxxx> wrote:
> > Hi Prashanth and Ashwin,
> >
> > On Wed, Feb 10, 2016 at 01:05:59PM -0700, Prashanth Prakash wrote:
> >> From: Ashwin Chaugule <ashwin.chaugule@xxxxxxxxxx>
> >>
> >> Previously the send_pcc_cmd() code checked if the
> >> PCC operation had completed before returning from
> >> the function. This check was performed regardless
> >> of the PCC op type (i.e. Read/Write). Knowing
> >> the type of cmd can be used to optimize the check
> >> and avoid needless waiting. e.g. with Write ops,
> >> the actual Writing is done before calling send_pcc_cmd().
> >> And the subsequent Writes will check if the channel is
> >> free at the entry of send_pcc_cmd() anyway.
> >>
> >> However, for Read cmds, we need to wait for the cmd
> >> completion bit to be flipped, since the actual Read
> >> ops follow after returning from the send_pcc_cmd(). So,
> >> only do the looping check at the end for Read ops.
> >>
> >> Also, instead of using udelay() calls, use ktime as a
> >> means to check for deadlines. The current deadline
> >> in which the Remote should flip the cmd completion bit
> >> is defined as N * Nominal latency. Where N is arbitrary
> >> and large enough to work on slow emulators and Nominal
> >> latency comes from the ACPI table (PCCT). This helps
> >> in working around the CONFIG_HZ effects on udelay()
> >> and also avoids needing different ACPI tables for Silicon
> >> and Emulation platforms.
> >>
> >> Signed-off-by: Ashwin Chaugule <ashwin.chaugule@xxxxxxxxxx>
> >> Signed-off-by: Prashanth Prakash <pprakash@xxxxxxxxxxxxxx>
> >> ---
> >> drivers/acpi/cppc_acpi.c | 99 ++++++++++++++++++++++++++++++++++--------------
> >> 1 file changed, 71 insertions(+), 28 deletions(-)
>
> [..]
>
> >>
> >> /*
> >> * Arbitrary Retries in case the remote processor is slow to respond
> >> - * to PCC commands.
> >> + * to PCC commands. Keeping it high enough to cover emulators where
> >> + * the processors run painfully slow.
> >> */
> >> #define NUM_RETRIES 500
> >>
> >> +static int check_pcc_chan(void)
> >> +{
> >> + int ret = -EIO;
> >> + struct acpi_pcct_shared_memory __iomem *generic_comm_base = pcc_comm_addr;
> >> + ktime_t next_deadline = ktime_add(ktime_get(), deadline);
> >> +
> >> + /* Retry in case the remote processor was too slow to catch up. */
> >> + while (!ktime_after(ktime_get(), next_deadline)) {
> >> + if (readw_relaxed(&generic_comm_base->status) & PCC_CMD_COMPLETE) {
> >
> > What do you think about polling for error too?
> > Firmware might set error bit and kernel will spin here for full cycle (maybe even
> > more than one time).
> >
>
> Hm. I dont think thats useful since we dont do anything special if the
> firmware errors out. Perhaps at some later point we can stop sending
> new requests if there are firmware errors, but then how would we know
> when to resume?
The suggestion is to jump out of polling loop quickly instead of spinning for full cycle.
With longer delays given by firmware the spinning issue on error will be worse.
This is not going to change behaviour on error paths (or in other words I don't suggest
to change error path behaviour right now).
Does specification describe any resume after error path? I don't see anything.
<snip>
Best regards,
Alexey Klimov.
--
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
