On Mon, 01 Sep 2014 19:11:44 +0200, Arnd Bergmann <arnd@xxxxxxxx> wrote:
> On Monday 01 September 2014 18:04:47 Catalin Marinas wrote:
> > On Mon, Sep 01, 2014 at 04:06:00PM +0100, Hanjun Guo wrote:
> > > +#ifdef CONFIG_ACPI
> > > +/* Configure some sensible defaults for ACPI mode */
> > > +static int smsc911x_probe_config_acpi(struct smsc911x_platform_config *config,
> > > + acpi_handle *ahandle)
> > > +{
> > > + if (!ahandle)
> > > + return -ENOSYS;
> > > +
> > > + config->phy_interface = PHY_INTERFACE_MODE_MII;
> > > +
> > > + config->flags |= SMSC911X_USE_32BIT;
> > > +
> > > + config->irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH;
> > > +
> > > + config->irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL;
> > > +
> > > + return 0;
> > > +}
> > > +#else
> >
> > I don't like this and it shows issues we have with ACPI on certain ARM
> > platforms. You hard-code these values to match the Juno platform. What
> > if we get another SoC which has different configuration here? For DT, we
> > have the smsc911x_probe_config_dt() which reads the relevant information
> > from DT. I think this kind of configuration would be more suitable as
> > _DSD properties and sharing the similar names with DT (but we go back to
> > the question about who's in charge of the _DSD properties).
>
> Good point, I totally missed that.
>
> There is of course the possibility to set those values based on the
> acpi_device_id, but that is exactly the part that _DSD is trying to
> avoid.
These are merely defaults. DSD parsing, when implemented, would be
override these default values.
>
> > > static int smsc911x_drv_probe(struct platform_device *pdev)
> > > {
> > > struct device_node *np = pdev->dev.of_node;
> > > + acpi_handle *ahandle = ACPI_HANDLE(&pdev->dev);
> > > struct net_device *dev;
> > > struct smsc911x_data *pdata;
> > > struct smsc911x_platform_config *config = dev_get_platdata(&pdev->dev);
> > > @@ -2436,6 +2464,9 @@ static int smsc911x_drv_probe(struct platform_device *pdev)
> > > }
> > >
> > > retval = smsc911x_probe_config_dt(&pdata->config, np);
> > > + if (retval)
> > > + retval = smsc911x_probe_config_acpi(&pdata->config, ahandle);
> > > +
> >
> > In most of the ACPI patches so far we check for ACPI first with DT as a
> > fall-back if ACPI is not enabled. This changes here.
>
> Does this really make a difference?
Nope. Only one of DT or ACPI will be matched.
>
> > I would prefer
> > something which probes only ACPI if the ACPI is enabled (run-time, not
> > config) otherwise DT only. E.g.
>
> (example missing?)
>
> I think we should have the equivalent of of_have_populated_dt(), to
> check whether acpi is being used to boot, and have that new function
> be hardcoded to zero in case of !IS_ENABLED(CONFIG_ACPI).
The code already accounts for it. If ACPI isn't enabled, or isn't
populated, then the ACPI_HANDLE macro will return NULL and the
smsc911x_probe_config_acpi() function will fail.
g.
--
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
