On Friday, March 29, 2013 09:05:35 AM Sarah Sharp wrote: > On Fri, Mar 29, 2013 at 04:05:54PM +0100, Martin Mokrejs wrote: > > [ 36.594171] xhci_hcd 0000:0b:00.0: xhci_suspend: stopping port polling. > > [ 36.594202] xhci_hcd 0000:0b:00.0: // Setting command ring address to 0xd6007001 > > [ 36.594247] xhci_hcd 0000:0b:00.0: hcd_pci_runtime_suspend: 0 > > [ 36.594349] xhci_hcd 0000:0b:00.0: PME# enabled > > [ 36.703695] r8169 0000:05:00.0 eth0: link down > > [ 37.098299] microcode: CPU0 updated to revision 0x28, date = 2012-04-24 > > [ 37.098941] microcode: CPU1 updated to revision 0x28, date = 2012-04-24 > > [ 37.098944] perf_event_intel: PEBS enabled due to microcode update > > [ 38.343029] r8169 0000:05:00.0 eth0: link up > > [ 39.094944] r8169 0000:05:00.0 eth0: link down > > [ 41.492768] r8169 0000:05:00.0 eth0: link up > > [ 62.782910] xhci_hcd 0000:0b:00.0: Poll event ring: 4294943584 > > [ 62.782938] xhci_hcd 0000:0b:00.0: op reg status = 0xffffffff > > [ 62.782939] xhci_hcd 0000:0b:00.0: HW died, polling stopped. > > [ 88.754183] pcieport 0000:00:1c.0: PME# enabled > > [ 88.764182] xhci_hcd 0000:0b:00.0: PME# disabled > > [ 88.764192] xhci_hcd 0000:0b:00.0: enabling bus mastering > > [ 88.764206] xhci_hcd 0000:0b:00.0: // Setting command ring address to 0xd6007001 > > [ 88.764242] xhci_hcd 0000:0b:00.0: Port Status Change Event for port 2 > > [ 88.764246] xhci_hcd 0000:0b:00.0: resume root hub > > [ 88.764259] xhci_hcd 0000:0b:00.0: handle_port_status: starting port polling. > > [ 88.764276] xhci_hcd 0000:0b:00.0: xhci_resume: starting port polling. > > [ 88.764281] xhci_hcd 0000:0b:00.0: hcd_pci_runtime_resume: 0 > > > > > > What "HW died? Why 1c.0 is here? What is this device actually doing? > > It's harmless. The xHCI polling loop to debug the host registers and > rings simply notices that the registers are reading as all ffs. I > believe that's normal when a PCI device is in D3. I just haven't had > time to make a patch to disable the polling loop when the host is suspended. > > So, for now, ignore the "HW died, polling stopped." messages. > > > Nevertheless, I went to check if if the USB3 socket dies after first unplug of device > > or not anymore thanks to the patch being tested: > > > > I plugged into the USB3.0 socket a mouse, it worked. Around its unplug I got: > > > > [ 94.954779] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 > > [ 94.954795] hub 3-0:1.0: hub_suspend > > [ 94.954802] usb usb3: bus auto-suspend, wakeup 1 > > [ 94.954817] xhci_hcd 0000:0b:00.0: xhci_hub_status_data: stopping port polling. > > [ 94.954835] xhci_hcd 0000:0b:00.0: xhci_suspend: stopping port polling. > > [ 94.954857] xhci_hcd 0000:0b:00.0: // Setting command ring address to 0xd6007001 > > [ 94.954898] xhci_hcd 0000:0b:00.0: hcd_pci_runtime_suspend: 0 > > [ 94.954983] xhci_hcd 0000:0b:00.0: PME# enabled > > [ 169.622513] hub 2-1:1.0: state 7 ports 8 chg 0000 evt 0004 > > [ 169.623057] hub 2-1:1.0: port 2, status 0101, change 0001, 12 Mb/s > > [ 169.777012] hub 2-1:1.0: debounce: port 2: total 100ms stable 100ms status 0x101 > > [ 169.856992] usb 2-1.2: new low-speed USB device number 4 using ehci-pci > > > > and the port was dead, no matter what "lsusb -v or -vv" options I tried. At about > > [ 169.622513] I plugged the mouse into a USB2.0 socket (do not know if that is 1a.0 or 1d.0). > > All right, I wonder if the USB core/xHCI driver is forgetting to clear a > port status change bit after the device is unplugged. That can cause > the xHCI host to not give us a port status change event later (and thus > no PME). Looking at the logs later, it doesn't seem like we do this > though. > > > If I run lsusb -vv it does (with the problematic patch): > > > > [ 1760.414086] pcieport 0000:00:1c.4: PME# disabled > > [ 1760.434314] xhci_hcd 0000:0b:00.0: PME# disabled > > [ 1760.434327] xhci_hcd 0000:0b:00.0: enabling bus mastering > > [ 1760.434338] xhci_hcd 0000:0b:00.0: // Setting command ring address to 0xd6007001 > > [ 1760.434360] xhci_hcd 0000:0b:00.0: Port Status Change Event for port 2 > > Ok, so the xHCI driver *is* getting a port status change event, and thus > must have gotten a PME. So the PCI layer is doing its job. > > > [ 1760.434363] xhci_hcd 0000:0b:00.0: resume root hub > > [ 1760.434367] xhci_hcd 0000:0b:00.0: handle_port_status: starting port polling. > > [ 1760.434378] xhci_hcd 0000:0b:00.0: xhci_resume: starting port polling. > > [ 1760.434383] xhci_hcd 0000:0b:00.0: hcd_pci_runtime_resume: 0 > > [ 1760.434388] usb usb3: usb auto-resume > > [ 1760.434407] hub 3-0:1.0: hub_resume > > [ 1760.434439] xhci_hcd 0000:0b:00.0: get port status, actual port 0 status = 0x2a0 > > [ 1760.434440] xhci_hcd 0000:0b:00.0: Get port status returned 0x100 > > [ 1760.434464] xhci_hcd 0000:0b:00.0: get port status, actual port 1 status = 0x202a0 > > [ 1760.434465] xhci_hcd 0000:0b:00.0: Get port status returned 0x10100 > > [ 1760.434492] xhci_hcd 0000:0b:00.0: clear port connect change, actual port 1 status = 0x2a0 > > Odd. The port status shows there's no device connected, but there was a > connect change: > > sarah@xanatos:~$ ./decode-port-status 0x202a0 > port status = 0x0202a0 > bit 0 (CCS) 0x0, device not connected > bit 1 (PED) 0x0, port disabled > bit 3 (OCA) 0x0, no over-current condition > bit 4 (PR) 0x0, port not in reset > bits 8:5 (PLS) 0x5, link is in the RxDetect state > bit 9 (PP) 0x1, port power on > bits 13:10 (speed) 0x0, Undefined > bits 15:14 (indicators) 0x0, port indicators are off > bit 17 (CSC) 0x1, connect change > bit 18 (PEC) 0x0, no port enable/disable change > bit 19 (WRC) 0x0, no warm port reset change > bit 20 (OCC) 0x0, no over-current change > bit 21 (PRC) 0x0, no port reset change > bit 22 (PLC) 0x0, no port link change > bit 23 (CEC) 0x0, no port config error change > bit 25 (WCE) 0x0, wake on connect disabled > bit 26 (WDE) 0x0, wake on disconnect disabled > bit 27 (WOE) 0x0, wake on over-current enable disabled > bit 30 (DR) 0x0, device is permanently attached > > RxDetect is the "I'm looking for a USB device" port state. > > > [ 1760.434642] usb usb4: usb wakeup-resume > > [ 1760.434646] usb usb4: usb auto-resume > > [ 1760.434661] hub 4-0:1.0: hub_resume > > [ 1760.434683] xhci_hcd 0000:0b:00.0: get port status, actual port 0 status = 0x2a0 > > [ 1760.434684] xhci_hcd 0000:0b:00.0: Get port status returned 0x2a0 > > [ 1760.434710] xhci_hcd 0000:0b:00.0: get port status, actual port 1 status = 0x2a0 > > [ 1760.434711] xhci_hcd 0000:0b:00.0: Get port status returned 0x2a0 > > [ 1760.434727] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 > > [ 1760.434757] xhci_hcd 0000:0b:00.0: set port remote wake mask, actual port 0 status = 0xe0002a0 > > [ 1760.434784] xhci_hcd 0000:0b:00.0: set port remote wake mask, actual port 1 status = 0xe0002a0 > > [ 1760.434791] hub 4-0:1.0: hub_suspend > > [ 1760.434796] usb usb4: bus auto-suspend, wakeup 1 > > [ 1760.434807] xhci_hcd 0000:0b:00.0: xhci_hub_status_data: stopping port polling. > > [ 1760.553734] xhci_hcd 0000:0b:00.0: xhci_hub_status_data: stopping port polling. > > [ 1760.553751] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 > > [ 1760.574793] xhci_hcd 0000:0b:00.0: get port status, actual port 0 status = 0x2a0 > > [ 1760.574794] xhci_hcd 0000:0b:00.0: Get port status returned 0x100 > > [ 1760.575300] xhci_hcd 0000:0b:00.0: get port status, actual port 1 status = 0x2a0 > > [ 1760.575301] xhci_hcd 0000:0b:00.0: Get port status returned 0x100 > > sarah@xanatos:~$ ./decode-port-status 0x2a0 > port status = 0x0002a0 > bit 0 (CCS) 0x0, device not connected > bit 1 (PED) 0x0, port disabled > bit 3 (OCA) 0x0, no over-current condition > bit 4 (PR) 0x0, port not in reset > bits 8:5 (PLS) 0x5, link is in the RxDetect state > bit 9 (PP) 0x1, port power on > bits 13:10 (speed) 0x0, Undefined > bits 15:14 (indicators) 0x0, port indicators are off > bit 17 (CSC) 0x0, no connect change > bit 18 (PEC) 0x0, no port enable/disable change > bit 19 (WRC) 0x0, no warm port reset change > bit 20 (OCC) 0x0, no over-current change > bit 21 (PRC) 0x0, no port reset change > bit 22 (PLC) 0x0, no port link change > bit 23 (CEC) 0x0, no port config error change > bit 25 (WCE) 0x0, wake on connect disabled > bit 26 (WDE) 0x0, wake on disconnect disabled > bit 27 (WOE) 0x0, wake on over-current enable disabled > bit 30 (DR) 0x0, device is permanently attached > > Nope, your host really isn't reporting there's a device connected > *at all*. That's just broken hardware, and there's really nothing > software can do if the hardware isn't reporting connect events, even > with polling. > > It also doesn't sound like the other TI redriver bug. That bug only > effected USB 3.0 ports, and when lsusb was run, we would find the port > in Compliance Mode. This is the host simply not reporting the USB 2.0 > port connect at all. > > Maybe if we completely disable PCI runtime PM for your host, we can work > around this bug? Well, that's what I've just asked Martin to try. Thanks, Rafael -- I speak only for myself. Rafael J. Wysocki, Intel Open Source Technology Center. -- To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
