On Monday, November 26, 2012 09:09:36 AM Aaron Lu wrote: > On 11/26/2012 09:11 AM, Rafael J. Wysocki wrote: > > On Monday, November 26, 2012 09:05:58 AM Aaron Lu wrote: > >> On 11/26/2012 09:03 AM, Rafael J. Wysocki wrote: > >>> On Monday, November 26, 2012 08:48:51 AM Aaron Lu wrote: > >>>> On 11/26/2012 08:50 AM, Rafael J. Wysocki wrote: > >>>>> On Tuesday, November 20, 2012 04:59:57 PM Aaron Lu wrote: > >>>>>> On 11/20/2012 02:00 PM, Aaron Lu wrote: > >>>>>>> On 11/19/2012 10:56 PM, Tejun Heo wrote: > >>>>>>>> I really think we need a way for (auto)pm and event polling to talk to > >>>>>>>> each other so that autopm can tell event poll to sod off while pm is > >>>>>>>> in effect. Trying to solve this from inside libata doesn't seem > >>>>>>>> right. The problem, again, seems to be figuring out which hardware > >>>>>>>> device maps to which block device. Hmmm... Any good ideas? > >>>>>>> > >>>>>>> A possible way of doing this is using pm qos. > >>>>>>> > >>>>>>> We currently have 2 pm qos flags, NO_POWER_OFF and REMOTE_WAKEUP, and we > >>>>>>> can add another one: NO_POLL, use it like the following: > >>>>>>> 1 Set the NO_POLL pm qos flag when the underlying driver thinks it is no > >>>>>>> longer necessary. In the ZPODD's case, it should be set when the > >>>>>>> device is to be powered off; > >>>>>>> 2 Clear it when poll is necessary again. In the ZPODD's case, when power > >>>>>>> is re-gained, this flag will be cleared. > >>>>>> > >>>>>> > >>>>>>> 3 In the disk_events_workfn, check if this flag is set, if so, simply > >>>>>>> return. > >>>>>> > >>>>>> It should be, skip calling disk->fops->check_events, but still queue the > >>>>>> work for next time's poll. > >>>>>> > >>>>>> -Aaron > >>>>>> > >>>>>>> > >>>>>>> The disk->driverfs_dev can be used to host the pm qos flag, ATA layer > >>>>>>> can access it through ata_device->sdev->sdev_gendev. > >>>>>>> > >>>>>>> Is this OK? > >>>>> > >>>>> No, I don't think so. PM QoS is about telling the layer that will put the > >>>>> device into low-power states what states are to be taken into consideration. > >>>>> In this case, however, we need to tell someone else that the device has been > >>>>> turned off. Clearly, we need a way to do that, but not through PM QoS. > >>>>> > >>>>> Did you consider using pm_runtime_suspended() to check the device status? > >>>> > >>>> The problem is, a device can be in runtime suspended state while still > >>>> needs to be polled... > >>> > >>> Well, maybe this is the problem, then? Why does it need to be polled when > >>> suspended? > >> > >> For ODDs, poll is not necessary only when ZP capable ODD is powered off. > >> For other ODDs, poll still needs to go on. > >> > >> ZP capable ODDs: > >> - runtime suspended, power remained(due to NO_POWER_OFF qos flag) > >> poll is needed > >> -- runtime suspended, power removed > >> poll is not needed > >> > >> Non ZP capable ODDs: > >> -- runtime suspended, power remained (power will never be removed) > >> poll is needed > >> > >> If we do not poll for the powered on case, we will lose media change > >> event. > > > > But the media change event should change the status from suspended to active, > > shouldn't it? > > The media change event is derived from the poll, if we stop the poll, how > can we know the event in the first place? OK, so what you're trying to say is that if the device is not turned off and the user opens the tray and inserts a media in there, we won't know that that happened without polling. Is that correct? If so, can you please remind me why we want to pretend that the device is suspended if we want to poll it? Rafael -- I speak only for myself. Rafael J. Wysocki, Intel Open Source Technology Center. -- To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
