On Wed, 2010-01-20 at 10:47 -0700, Bjorn Helgaas wrote:
> On Monday 28 December 2009 06:44:20 pm yakui.zhao@xxxxxxxxx wrote:
> > From: Zhao Yakui <yakui.zhao@xxxxxxxxx>
> >
> > ACPI 4.0 spec adds the ACPI IPMI opregion, which means that the ACPI AML
> > code can also communicate with the BMC controller. This is to install
> > the ACPI IPMI opregion and enable the ACPI to access the BMC controller
> > through the IPMI message.
> >
> > It will create IPMI user interface for every IPMI device detected
> > in ACPI namespace and install the corresponding IPMI opregion space handler.
> > Then it can enable ACPI to access the BMC controller through the IPMI
> > message.
> >
> > The following describes how to process the IPMI request in IPMI space handler:
> > 1. format the IPMI message based on the request in AML code.
> > IPMI system address. Now the address type is SYSTEM_INTERFACE_ADDR_TYPE
> > IPMI net function & command
> > IPMI message payload
> > 2. send the IPMI message by using the function of ipmi_request_settime
> > 3. wait for the completion of IPMI message. It can be done in different
> > routes: One is in handled in IPMI user recv callback function. Another is
> > handled in timeout function.
> > 4. format the IPMI response and return it to ACPI AML code.
>
> Sorry for the long delay in reviewing this. It's starting to make a lot
> more sense to me, so it must be close to ready :-) I have a few minor
> comments below, but nothing major.
Thanks for the review.
I will remove the unnecessary comment/meaningless check and then send it
again.
Thanks.
>
> > Signed-off-by: Zhao Yakui <yakui.zhao@xxxxxxxxx>
> > Reviewed-by: Bjorn Helgaas <bjorn.helgaas@xxxxxx>
>
> See Documentation/SubmittingPatches; you shouldn't add this yourself
> just because I've given you feedback on previous versions. Normally,
> somebody who has reviewed the patch and supports it in its present
> form will reply with something like "Reviewed-by: xxx".
>
> > ---
> > drivers/char/ipmi/ipmi_si_intf.c | 493 +++++++++++++++++++++++++++++++++++++-
> > 1 files changed, 489 insertions(+), 4 deletions(-)
> >
> > diff --git a/drivers/char/ipmi/ipmi_si_intf.c b/drivers/char/ipmi/ipmi_si_intf.c
> > index 3f6ca11..be57d1c 100644
> > --- a/drivers/char/ipmi/ipmi_si_intf.c
> > +++ b/drivers/char/ipmi/ipmi_si_intf.c
> > @@ -65,7 +65,7 @@
> > #include <linux/string.h>
> > #include <linux/ctype.h>
> > #include <linux/pnp.h>
> > -
> > +#include <linux/ipmi.h>
> > #ifdef CONFIG_PPC_OF
> > #include <linux/of_device.h>
> > #include <linux/of_platform.h>
> > @@ -1808,6 +1808,463 @@ static __devinit void hardcode_find_bmc(void)
> >
> > #include <linux/acpi.h>
> >
> > +#define IPMI_FLAGS_HANDLER_INSTALL 0
> > +#define ACPI_IPMI_OK 0
> > +#define ACPI_IPMI_TIMEOUT 0x10
> > +#define ACPI_IPMI_UNKNOWN 0x07
> > +/* the IPMI timeout is 30s */
> > +#define IPMI_TIMEOUT (30 * HZ)
> > +
> > +struct acpi_ipmi_device {
> > + acpi_handle handle;
> > + struct acpi_device *device;
> > + /* the device list attached to driver_data.ipmi_devices */
> > + struct list_head head;
> > + ipmi_user_t user_interface;
> > + struct mutex mutex_lock;
> > + /* the IPMI request message list */
>
> Remove this comment.
>
> > + struct list_head tx_msg_list;
> > + long curr_msgid;
> > + /* IPMI flags */
>
> Remove this comment.
>
> > + unsigned long flags;
> > + /* IPMI interface number */
>
> Remove this comment.
>
> > + int ipmi_ifnum;
> > + struct smi_info *smi_info;
> > +};
> > +
> > +struct ipmi_driver_data {
> > + int device_count;
> > + struct list_head ipmi_devices;
> > + struct ipmi_smi_watcher bmc_events;
> > + struct ipmi_user_hndl ipmi_hndlrs;
> > +};
> > +
> > +struct acpi_ipmi_msg {
> > + /* message list */
> > + struct list_head head;
> > + /*
> > + * General speaking the addr type should be SI_ADDR_TYPE. And
> > + * the addr channel should be BMC.
> > + * In fact it can also be IPMB type. But we will have to
> > + * parse it from the Netfn command buffer. It is so complex
> > + * that it is skipped.
> > + */
> > + struct ipmi_addr addr;
> > + /* tx message id */
>
> Remove this comment.
>
> > + long tx_msgid;
> > + /* it is used to track whether the IPMI message is finished */
> > + struct completion tx_complete;
> > + struct kernel_ipmi_msg tx_message;
> > + int msg_done;
> > + /* tx data . And copy it from ACPI object buffer */
> > + u8 tx_data[64];
> > + int tx_len;
> > + /* get the response data */
> > + u8 rx_data[64];
> > + /* the response length. The netfn & cmd is excluded. */
> > + int rx_len;
> > + struct acpi_ipmi_device *device;
> > +};
> > +
> > +/*
> > + * IPMI request/response buffer.
> > + * The length is 66 bytes.
> > + */
>
> /* IPMI request/response buffer per ACPI 4.0, sec 5.5.2.4.3.2 */
>
> > +struct acpi_ipmi_buffer {
> > + /* status code of a given IPMI command */
> > + u8 status_code;
> > + /* the length of the payload */
> > + u8 length;
> > + /*
> > + * the payload. Before the operation is carried out, it represents the
> > + * request message payload. After the operation is carried out, it
> > + * stores the response message returned by IPMI command.
> > + */
>
> Remove these comments (they're the same as what's in the spec), and
> make the names match the spec, e.g., "status", not "status_code".
>
> > + u8 data[64];
> > +};
> > +
> > +
> > +static void ipmi_register_bmc(int iface, struct device *dev);
> > +static void ipmi_bmc_gone(int iface);
> > +static void ipmi_msg_handler(struct ipmi_recv_msg *msg, void *user_msg_data);
> > +
> > +static struct ipmi_driver_data driver_data = {
> > + .ipmi_devices = LIST_HEAD_INIT(driver_data.ipmi_devices),
> > + .bmc_events = {
> > + .owner = THIS_MODULE,
> > + .new_smi = ipmi_register_bmc,
> > + .smi_gone = ipmi_bmc_gone,
> > + },
> > + .ipmi_hndlrs = {
> > + .ipmi_recv_hndl = ipmi_msg_handler,
> > + },
> > +};
> > +
> > +static
> > +struct acpi_ipmi_msg *acpi_alloc_ipmi_msg(struct acpi_ipmi_device *ipmi)
> > +{
> > + struct acpi_ipmi_msg *ipmi_msg;
> > +
> > + ipmi_msg = kzalloc(sizeof(struct acpi_ipmi_msg), GFP_KERNEL);
> > + if (!ipmi_msg) {
> > + printk(KERN_DEBUG "Can't allocate memory for ipmi_msg\n");
>
> All these error printks should be dev_dbg() or dev_warn() so that if
> a user ever sees the messages, we have get a clue about where to look.
>
> > + return NULL;
> > + }
> > + init_completion(&ipmi_msg->tx_complete);
> > + INIT_LIST_HEAD(&ipmi_msg->head);
> > + ipmi_msg->device = ipmi;
> > + return ipmi_msg;
> > +}
> > +
> > +static void acpi_format_ipmi_msg(struct acpi_ipmi_msg *tx_msg,
> > + acpi_physical_address address,
> > + acpi_integer *value)
> > +{
> > + struct kernel_ipmi_msg *msg;
> > + u8 temp_value;
> > + struct acpi_ipmi_buffer *buffer;
> > + struct acpi_ipmi_device *device;
> > +
> > + msg = &tx_msg->tx_message;
> > + /* get the netfn */
> > + temp_value = (address >> 8) & 0xff;
> > + msg->netfn = temp_value;
> > + /* get the command */
> > + temp_value = address & 0xff;
> > + msg->cmd = temp_value;
>
> #define IPMI_OP_RGN_NETFN(offset) ((offset >> 8) & 0xff)
> #define IPMI_OP_RGN_CMD(offset) (offset & 0xff)
>
> /*
> * IPMI network function and command are encoded in the address
> * within the IPMI OpRegion; see ACPI 4.0, sec 5.5.2.4.3.
> */
> msg->netfn = IPMI_OP_RGN_NETFN(address);
> msg->cmd = IPMI_OP_RGN_CMD(address);
>
> > + msg->data = tx_msg->tx_data;
> > + /*
> > + * value is the parameter passed by the IPMI opregion space handler.
> > + * It points to the IPMI request message buffer
> > + */
> > + buffer = (struct acpi_ipmi_buffer *)value;
> > + /* copy the tx message data */
> > + msg->data_len = buffer->length;
> > + memcpy(tx_msg->tx_data, buffer->data, msg->data_len);
> > + /*
> > + * now the default type is SYSTEM_INTERFACE and channel type is BMC.
> > + * If the netfn is APP_REQUEST and the cmd is SEND_MESSAGE,
> > + * the addr type should be changed to IPMB.
> > + */
> > + tx_msg->addr.addr_type = IPMI_SYSTEM_INTERFACE_ADDR_TYPE;
> > + tx_msg->addr.channel = IPMI_BMC_CHANNEL;
> > + tx_msg->addr.data[0] = 0;
> > +
> > + /*
> > + * If the netfn is APP_REQUEST and the cmd is SEND_MESSAGE, we should
> > + * parse the IPMI request message buffer to get the IPMB address.
> > + * If so, please fix me.
> > + */
> > +
> > + /* Get the msgid */
> > + device = tx_msg->device;
> > + mutex_lock(&device->mutex_lock);
> > + device->curr_msgid++;
> > + tx_msg->tx_msgid = device->curr_msgid;
> > + mutex_unlock(&device->mutex_lock);
> > +}
> > +
> > +static void acpi_format_ipmi_response(struct acpi_ipmi_msg *msg,
> > + acpi_integer *value, int timeout)
> > +{
> > + struct acpi_ipmi_buffer *buffer;
> > +
> > + /*
> > + * value is also used as output parameter. It represents the response
> > + * IPMI message returned by IPMI command.
> > + */
> > + buffer = (struct acpi_ipmi_buffer *)value;
> > + /* when timeout is zero, it means that the timeout happens */
>
> Remove this comment.
>
> > + if (!timeout) {
> > + /* the status code is ACPI_IPMI_TIMEOUT */
>
> Remove this comment.
>
> > + buffer->status_code = ACPI_IPMI_TIMEOUT;
> > + return;
> > + }
> > + /*
> > + * If the flag of msg_done is not set, it means that the IPMI command
> > + * is not executed correctly.
> > + * The status code will be ACPI_IPMI_UNKNOWN.
> > + */
> > + if (!msg->msg_done) {
> > + buffer->status_code = ACPI_IPMI_UNKNOWN;
> > + return;
> > + }
> > + /*
> > + * If the IPMI response message is obtained correctly, the status code
> > + * will be ACPI_IPMI_OK
> > + */
>
> Remove this comment.
>
> > + buffer->status_code = ACPI_IPMI_OK;
> > + buffer->length = msg->rx_len;
> > + memcpy(buffer->data, msg->rx_data, msg->rx_len);
> > +}
> > +
> > +static void ipmi_destroy_tx_msg(struct acpi_ipmi_device *ipmi)
> > +{
> > + struct acpi_ipmi_msg *tx_msg = NULL, *temp;
> > + int count = 20;
> > +
> > + list_for_each_entry_safe(tx_msg, temp, &ipmi->tx_msg_list, head) {
> > + /* wake up the sleep thread on the Tx msg */
> > + complete(&tx_msg->tx_complete);
> > + }
> > + /* wait for about 20 ticks to flush the tx message list */
> > + while (count--) {
> > + if (list_empty(&ipmi->tx_msg_list))
> > + break;
> > + schedule_timeout(1);
> > + }
> > + if (!list_empty(&ipmi->tx_msg_list))
> > + printk(KERN_DEBUG "tx msg list is not NULL\n");
> > +
> > +}
> > +
> > +static void ipmi_msg_handler(struct ipmi_recv_msg *msg, void *user_msg_data)
> > +{
> > + struct acpi_ipmi_device *ipmi_device = user_msg_data;
> > + int msg_found = 0;
> > + struct acpi_ipmi_msg *tx_msg;
> > +
> > + if (msg->user != ipmi_device->user_interface) {
> > + printk(KERN_DEBUG "Incorrect IPMI user\n");
> > + ipmi_free_recv_msg(msg);
> > + return;
> > + }
> > + mutex_lock(&ipmi_device->mutex_lock);
> > + list_for_each_entry(tx_msg, &ipmi_device->tx_msg_list, head) {
> > + if (msg->msgid == tx_msg->tx_msgid) {
> > + /* find the message id */
> > + msg_found = 1;
> > + break;
> > + }
> > + }
> > +
> > + mutex_unlock(&ipmi_device->mutex_lock);
> > + if (!msg_found) {
> > + /* no matched msg is found . But we should free it */
> > + ipmi_free_recv_msg(msg);
> > + printk(KERN_DEBUG "Incorrect MSG is found \n");
> > + return;
> > + }
> > +
> > + if (msg->msg.data_len > 1) {
> > + /* copy the response data to Rx_data buffer */
> > + memcpy(tx_msg->rx_data, msg->msg_data, msg->msg.data_len);
> > + tx_msg->rx_len = msg->msg.data_len;
> > + tx_msg->msg_done = 1;
> > + }
> > + complete(&tx_msg->tx_complete);
> > + ipmi_free_recv_msg(msg);
> > +};
> > +
> > +static void ipmi_register_bmc(int iface, struct device *dev)
> > +{
> > + struct acpi_ipmi_device *ipmi_device, *temp;
> > + struct acpi_device *device;
> > + ipmi_user_t user;
> > + int err;
> > +
> > + if (list_empty(&driver_data.ipmi_devices))
> > + return;
> > +
> > + list_for_each_entry_safe(ipmi_device, temp,
> > + &driver_data.ipmi_devices, head) {
> > + device = ipmi_device->device;
> > + if (ipmi_device->user_interface) {
> > + /*
> > + * Only one user interface is allowed to be registered
> > + * for one IPMI device.
> > + * If we already create the user interface for
> > + * one IPMI device, skip it
> > + */
> > + continue;
> > + }
> > + if (dev == &device->dev) {
> > + /*
> > + * If the dev is identical to the ACPI device,
> > + * create the user interface.
> > + */
> > + err = ipmi_create_user(iface, &driver_data.ipmi_hndlrs,
> > + ipmi_device, &user);
> > + if (err == 0) {
> > + ipmi_device->user_interface = user;
> > + ipmi_device->ipmi_ifnum = iface;
> > + }
> > + }
> > + }
> > +}
> > +
> > +static void ipmi_bmc_gone(int iface)
> > +{
> > + struct acpi_ipmi_device *ipmi_device, *temp;
> > +
> > + if (list_empty(&driver_data.ipmi_devices))
> > + return;
> > +
> > + list_for_each_entry_safe(ipmi_device, temp,
> > + &driver_data.ipmi_devices, head) {
> > + if (ipmi_device->user_interface &&
> > + (ipmi_device->ipmi_ifnum == iface)) {
> > + ipmi_destroy_user(ipmi_device->user_interface);
> > + ipmi_device->user_interface = NULL;
> > + ipmi_destroy_tx_msg(ipmi_device);
> > + }
> > + }
> > +}
> > +/* --------------------------------------------------------------------------
> > + * Address Space Management
> > + -------------------------------------------------------------------------- */
> > +/*
> > + * This is the IPMI opregion space handler.
> > + * @function: indicates the read/write. In fact as the IPMI message is driven
> > + * by command, only write is meaningful.
> > + * @address: This contains the netfn/command of IPMI request message.
> > + * @bits : not used.
> > + * @value : it is an in/out parameter. It points to the IPMI message buffer.
> > + * Before the IPMI message is sent, it represents the actual request
> > + * IPMI message. After the IPMI message is finished, it represents
> > + * the response IPMI message returned by IPMI command.
> > + * @handler_context: IPMI device context.
> > + */
> > +
> > +static acpi_status
> > +acpi_ipmi_space_handler(u32 function, acpi_physical_address address,
> > + u32 bits, acpi_integer *value,
> > + void *handler_context, void *region_context)
> > +{
> > + struct acpi_ipmi_msg *tx_msg = NULL;
> > + struct acpi_ipmi_device *ipmi_device =
> > + (struct acpi_ipmi_device *) handler_context;
> > + int err;
> > + acpi_status status;
>
> Add a blank line here, between the local variable list and the first line
> of comments or code.
>
> > + /*
> > + * IPMI opregion message.
> > + * IPMI message is firstly written to the BMC and system software
> > + * can get the respsonse. So it is unmeaningful for the IPMI read
> > + * access.
> > + */
> > + if ((function & ACPI_IO_MASK) == ACPI_READ) {
> > + /* Read function is not supported. AE_TYPE is returned. */
>
> Remove this comment.
>
> > + return AE_TYPE;
> > + }
> > + if (!ipmi_device->user_interface)
> > + return AE_NOT_EXIST;
>
> Check this first, before checking the access type, i.e., check for the
> most generic failures first, then proceed to the more specific.
>
> > +
> > + tx_msg = acpi_alloc_ipmi_msg(ipmi_device);
> > + if (!tx_msg)
> > + return AE_NO_MEMORY;
> > +
> > + acpi_format_ipmi_msg(tx_msg, address, value);
> > + mutex_lock(&ipmi_device->mutex_lock);
> > + list_add_tail(&tx_msg->head, &ipmi_device->tx_msg_list);
> > + mutex_unlock(&ipmi_device->mutex_lock);
> > + err = ipmi_request_settime(ipmi_device->user_interface,
> > + &tx_msg->addr,
> > + tx_msg->tx_msgid,
> > + &tx_msg->tx_message,
> > + NULL, 0, 0, 0);
> > + if (err) {
> > + status = AE_ERROR;
> > + goto end_label;
> > + }
> > + err = wait_for_completion_timeout(&tx_msg->tx_complete, IPMI_TIMEOUT);
> > +
> > + acpi_format_ipmi_response(tx_msg, value, err);
> > + status = AE_OK;
> > +
> > +end_label:
> > + mutex_lock(&ipmi_device->mutex_lock);
> > + list_del(&tx_msg->head);
> > + mutex_unlock(&ipmi_device->mutex_lock);
> > + kfree(tx_msg);
> > + return status;
> > +}
> > +
> > +static void ipmi_remove_handler(struct acpi_ipmi_device *ipmi)
> > +{
> > + if (!test_bit(IPMI_FLAGS_HANDLER_INSTALL, &ipmi->flags))
> > + return;
> > +
> > + acpi_remove_address_space_handler(ipmi->handle,
> > + ACPI_ADR_SPACE_IPMI, &acpi_ipmi_space_handler);
> > +
> > + clear_bit(IPMI_FLAGS_HANDLER_INSTALL, &ipmi->flags);
> > +}
> > +
> > +static int ipmi_install_handler(struct acpi_ipmi_device *ipmi)
> > +{
> > + acpi_status status;
> > +
> > + if (test_bit(IPMI_FLAGS_HANDLER_INSTALL, &ipmi->flags))
> > + return 0;
> > +
> > + status = acpi_install_address_space_handler(ipmi->handle,
> > + ACPI_ADR_SPACE_IPMI,
> > + &acpi_ipmi_space_handler,
> > + NULL, ipmi);
> > + if (ACPI_FAILURE(status)) {
> > + printk(KERN_DEBUG "Can't register IPMI opregion %s\n",
> > + acpi_device_bid(ipmi->device));
>
> Use dev_warn() here. You should use the PNP dev, not the
> ACPI dev, so you might have to change the prototypes of these
> functions to take a struct pnp_dev * rather than a struct
> acpi_ipmi_device *.
Ok. I will change the argument from acpi_ipmi_device * to pnp_dev *.
And we can get the pointer of acpi_ipmi_device by using pnp_get_drvdata.
Then I can use the dev_warn to print the debug info.
thanks.
>
> > + return -EINVAL;
> > + }
> > +
> > + test_bit(IPMI_FLAGS_HANDLER_INSTALL, &ipmi->flags);
>
> There's no point in testing this bit here. test_bit() has no side
> effects, to it's useless unless you test the return value.
thanks for the pointing out this issue. It should be set_bit. I will fix
it.
>
> > + return 0;
> > +}
> > +
> > +static void acpi_register_ipmi_handler(struct acpi_ipmi_device *ipmi_device)
> > +{
> > + if (list_empty(&driver_data.ipmi_devices)) {
> > + /*
> > + * when we try to register the first IPI0001 device, register
> > + * the smi_watcher.
> > + */
>
> This comment (and the curly braces) are unnecessary.
>
> > + ipmi_smi_watcher_register(&driver_data.bmc_events);
> > + }
> > +
> > + mutex_init(&ipmi_device->mutex_lock);
> > + INIT_LIST_HEAD(&ipmi_device->tx_msg_list);
> > +
> > + if (ipmi_install_handler(ipmi_device)) {
> > + /*
> > + * can't register the IPMI opregion. We will print
> > + * some debug info and continue to register ipmi
> > + * opregion for next device.
> > + */
> > + printk(KERN_DEBUG "Can't register IPMI opregion %s\n",
> > + acpi_device_bid(ipmi_device->device));
>
> You already print this info in ipmi_install_handler(), so I don't
> think you need to do it again.
>
> > + }
> > + list_add(&ipmi_device->head, &driver_data.ipmi_devices);
> > +}
> > +
> > +static void acpi_remove_ipmi_handler(struct acpi_ipmi_device *ipmi_device)
> > +{
> > + if (!ipmi_device)
> > + return;
>
> Remove this test. If we ever call this with NULL, there's a bug
> somewhere else in this driver, and we should find and fix it rather
> than cover it up by silently returning.
>
> > + if (ipmi_device->user_interface) {
> > + /*
> > + * If the IPMI user interface is created, it
> > + * should be destroyed.
> > + */
>
> This comment is unnecessary.
>
> > + ipmi_destroy_user(ipmi_device->user_interface);
> > + ipmi_device->user_interface = NULL;
> > + }
> > + list_del(&ipmi_device->head);
> > +
> > + if (!list_empty(&ipmi_device->tx_msg_list))
> > + ipmi_destroy_tx_msg(ipmi_device);
> > +
> > + ipmi_remove_handler(ipmi_device);
> > + if (list_empty(&driver_data.ipmi_devices)) {
> > + /*
> > + * when no IPI0001 device is in the list, uninstall the
> > + * smi_watcher.
> > + */
>
> This comment (and the curly braces) are unnecessary.
>
> > + ipmi_smi_watcher_unregister(&driver_data.bmc_events);
> > + }
> > +}
> > +
> > /*
> > * Once we get an ACPI failure, we don't try any more, because we go
> > * through the tables sequentially. Once we don't find a table, there
> > @@ -2033,6 +2490,8 @@ static int __devinit ipmi_pnp_probe(struct pnp_dev *dev,
> > acpi_handle handle;
> > acpi_status status;
> > unsigned long long tmp;
> > + int ret;
> > + struct acpi_ipmi_device *p_ipmi;
> >
> > acpi_dev = pnp_acpi_device(dev);
> > if (!acpi_dev)
> > @@ -2042,6 +2501,13 @@ static int __devinit ipmi_pnp_probe(struct pnp_dev *dev,
> > if (!info)
> > return -ENOMEM;
> >
> > + p_ipmi = kzalloc(sizeof(*p_ipmi), GFP_KERNEL);
> > + if (!p_ipmi) {
> > + printk(KERN_ERR "Can't allocate memory for IPMI device\n");
>
> Use dev_err() here (or just remove the message; I don't think it's very
> useful).
>
> > + kfree(info);
> > + return -ENOMEM;
> > + }
> > +
> > info->addr_source = "ACPI";
> >
> > handle = acpi_dev->handle;
> > @@ -2094,20 +2560,39 @@ static int __devinit ipmi_pnp_probe(struct pnp_dev *dev,
> > }
> >
> > info->dev = &acpi_dev->dev;
> > - pnp_set_drvdata(dev, info);
> > + p_ipmi->smi_info = info;
> > + pnp_set_drvdata(dev, p_ipmi);
> >
> > - return try_smi_init(info);
> > + p_ipmi->device = acpi_dev;
> > + p_ipmi->handle = handle;
> > + p_ipmi->ipmi_ifnum = -1;
>
> I would finish filling in p_ipmi before setting the driver data,
> e.g.,
>
> p_ipmi->smi_info = info;
> p_ipmi->device = acpi_dev;
> p_ipmi->handle = handle;
> p_ipmi->ipmi_ifnum = -1;
> pnp_set_drvdata(dev, p_ipmi);
>
> > + acpi_register_ipmi_handler(p_ipmi);
> > +
> > + ret = try_smi_init(info);
> > + if (!ret)
> > + return ret;
> > + else
> > + acpi_remove_ipmi_handler(p_ipmi);
> >
> > err_free:
> > + pnp_set_drvdata(dev, NULL);
> > + kfree(p_ipmi);
> > kfree(info);
> > return -EINVAL;
> > }
> >
> > static void __devexit ipmi_pnp_remove(struct pnp_dev *dev)
> > {
> > - struct smi_info *info = pnp_get_drvdata(dev);
> > + struct acpi_ipmi_device *p_ipmi;
> > + struct smi_info *info;
> > +
> > + p_ipmi = pnp_get_drvdata(dev);
> > + info = p_ipmi->smi_info;
> >
> > cleanup_one_si(info);
> > + acpi_remove_ipmi_handler(p_ipmi);
> > + pnp_set_drvdata(dev, NULL);
> > + kfree(p_ipmi);
> > }
> >
> > static const struct pnp_device_id pnp_dev_table[] = {
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
