Hi!
> > Aug 6 11:00:10 amd kernel: ACPI: Critical trip point
> > Aug 6 11:00:10 amd kernel: Critical temperature reached (128 C),
> > shutting down.
> > Aug 6 11:00:10 amd shutdown[24414]: shutting down for system halt
> >
> > ...and machine went down at that point :-(.
>
> I hope you can easily reproduce it?
>
> So it's new in 2.6.27rc1 and wasn't in 2.6.26? Can you please
Yes, I'm very sure. It makes machine basically unusable.
> double check that? Are there are new warnings in the boot logs
> from ACPI compared to .26?
Will take a look.... ... I don't see anything obvious, diff is below.
> I looked through the pile of patches that went in for ACPI and the
> only candidate that might have imho caused this would be
> ea51011a27db48ea0a80a5e20de3969b292d5d4d. Can you please
> try reverting that. If that doesn't help a full bisect will be needed.
Not that one :-(. Thinkpad does not even have fan device: it is
controlled by hardware.
Pavel
--- /tmp/dmesg.26 2008-08-12 11:38:44.000000000 +0200
+++ /tmp/dmesg.rc2 2008-08-12 11:15:44.000000000 +0200
@@ -1,4 +1,4 @@
-Linux version 2.6.26 (pavel@amd) (gcc version 4.1.3 20071209 (prerelease) (Debian 4.1.2-18)) #313 SMP Mon Jul 14 08:33:14 CEST 2008
+Linux version 2.6.27-rc2 (pavel@amd) (gcc version 4.1.3 20071209 (prerelease) (Debian 4.1.2-18)) #322 SMP Thu Aug 7 11:58:09 CEST 2008
PAT disabled. Not yet verified on this CPU type.
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
@@ -16,31 +16,13 @@
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
-1142MB HIGHMEM available.
-896MB LOWMEM available.
-found SMP MP-table at [c00f67f0] 000f67f0
-Entering add_active_range(0, 0, 521936) 0 entries of 256 used
-Zone PFN ranges:
- DMA 0 -> 4096
- Normal 4096 -> 229376
- HighMem 229376 -> 521936
-Movable zone start PFN for each node
-early_node_map[1] active PFN ranges
- 0: 0 -> 521936
-On node 0 totalpages: 521936
- DMA zone: 32 pages used for memmap
- DMA zone: 0 pages reserved
- DMA zone: 4064 pages, LIFO batch:0
- Normal zone: 1760 pages used for memmap
- Normal zone: 223520 pages, LIFO batch:31
- HighMem zone: 2286 pages used for memmap
- HighMem zone: 290274 pages, LIFO batch:31
- Movable zone: 0 pages used for memmap
+last_pfn = 0x7f6d0 max_arch_pfn = 0x100000
+kernel direct mapping tables up to 38000000 @ 7000-c000
DMI present.
ACPI: RSDP 000F67C0, 0024 (r2 LENOVO)
ACPI: XSDT 7F6D191C, 0084 (r1 LENOVO TP-7B 2140 LTP 0)
ACPI: FACP 7F6D1A00, 00F4 (r3 LENOVO TP-7B 2140 LNVO 1)
-ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20080321]
+ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20080609]
ACPI: DSDT 7F6D1D90, CFB9 (r1 LENOVO TP-7B 2140 MSFT 100000E)
ACPI: FACS 7F6F4000, 0040
ACPI: SSDT 7F6D1BB4, 01DC (r1 LENOVO TP-7B 2140 MSFT 100000E)
@@ -54,6 +36,37 @@
ACPI: SSDT 7F6F28A4, 00A6 (r1 LENOVO TP-7B 2140 INTL 20050513)
ACPI: SSDT 7F6F294A, 04F7 (r1 LENOVO TP-7B 2140 INTL 20050513)
ACPI: SSDT 7F6F2E41, 01D8 (r1 LENOVO TP-7B 2140 INTL 20050513)
+1142MB HIGHMEM available.
+896MB LOWMEM available.
+ mapped low ram: 0 - 38000000
+ low ram: 00000000 - 38000000
+ bootmap 00008000 - 0000f000
+(8 early reservations) ==> bootmem [0000000000 - 0038000000]
+ #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
+ #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
+ #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
+ #3 [0000200000 - 0000c07128] TEXT DATA BSS ==> [0000200000 - 0000c07128]
+ #4 [0000c08000 - 0000c1d000] INIT_PG_TABLE ==> [0000c08000 - 0000c1d000]
+ #5 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
+ #6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
+ #7 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000]
+Scan SMP from c0000000 for 1024 bytes.
+Scan SMP from c009fc00 for 1024 bytes.
+Scan SMP from c00f0000 for 65536 bytes.
+found SMP MP-table at [c00f67f0] 000f67f0
+Zone PFN ranges:
+ DMA 0x00000000 -> 0x00001000
+ Normal 0x00001000 -> 0x00038000
+ HighMem 0x00038000 -> 0x0007f6d0
+Movable zone start PFN for each node
+early_node_map[2] active PFN ranges
+ 0: 0x00000000 -> 0x0000009f
+ 0: 0x00000100 -> 0x0007f6d0
+On node 0 totalpages: 521839
+free_area_init_node: node 0, pgdat c0942e80, node_mem_map c1001000
+ DMA zone: 3967 pages, LIFO batch:0
+ Normal zone: 223520 pages, LIFO batch:31
+ HighMem zone: 290274 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
@@ -70,26 +83,27 @@
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
-Allocating PCI resources starting at 88000000 (gap: 80000000:70000000)
+SMP: Allowing 2 CPUs, 0 hotplug CPUs
+mapped APIC to ffffb000 (fee00000)
+mapped IOAPIC to ffffa000 (fec00000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
-SMP: Allowing 2 CPUs, 0 hotplug CPUs
-PERCPU: Allocating 37800 bytes of per cpu data
-NR_CPUS: 2, nr_cpu_ids: 2
-Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517858
+Allocating PCI resources starting at 88000000 (gap: 80000000:70000000)
+PERCPU: Allocating 37552 bytes of per cpu data
+NR_CPUS: 2, nr_cpu_ids: 2, nr_node_ids 1
+Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517761
Kernel command line: root=/dev/sda4 resume=/dev/sda1 psmouse.psmouse_proto=imps psmouse_proto=imps psmouse.proto=imps vga=791 init=/tmp/swsusp-init acpi_sleep=s3_bios,s3_mode no_console_suspend
Unknown boot option `psmouse.psmouse_proto=imps': ignoring
-mapped APIC to ffffb000 (fee00000)
-mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Extended CMOS year: 2000
-Detected 1828.792 MHz processor.
+TSC calibrated against PM_TIMER
+Detected 1828.748 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
@@ -100,23 +114,23 @@
... MAX_LOCKDEP_ENTRIES: 8192
... MAX_LOCKDEP_CHAINS: 16384
... CHAINHASH_SIZE: 8192
- memory used by lock dependency info: 992 kB
+ memory used by lock dependency info: 1056 kB
per task-struct memory footprint: 1920 bytes
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
-Memory: 2059068k/2087744k available (5320k kernel code, 27516k reserved, 2458k data, 320k init, 1170240k highmem)
+Memory: 2058760k/2087744k available (5438k kernel code, 27692k reserved, 2511k data, 344k init, 1170240k highmem)
virtual kernel memory layout:
- fixmap : 0xfff7f000 - 0xfffff000 ( 512 kB)
+ fixmap : 0xfff83000 - 0xfffff000 ( 496 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
- .init : 0xc09a1000 - 0xc09f1000 ( 320 kB)
- .data : 0xc0732166 - 0xc0998a08 (2458 kB)
- .text : 0xc0200000 - 0xc0732166 (5320 kB)
+ .init : 0xc09cb000 - 0xc0a21000 ( 344 kB)
+ .data : 0xc074fbc6 - 0xc09c38f0 (2511 kB)
+ .text : 0xc0200000 - 0xc074fbc6 (5438 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 32 of 32 pages preallocated
hpet clockevent registered
-Calibrating delay using timer specific routine.. 3662.04 BogoMIPS (lpj=7324080)
+Calibrating delay loop (skipped), value calculated using timer frequency.. 3657.49 BogoMIPS (lpj=7314992)
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
@@ -124,7 +138,7 @@
CPU: Processor Core ID: 0
using mwait in idle threads.
Checking 'hlt' instruction... OK.
-ACPI: Core revision 20080321
+ACPI: Core revision 20080609
Parsing all Control Methods:
Table [DSDT](id 0001) - 1592 Objects with 69 Devices 429 Methods 28 Regions
Parsing all Control Methods:
@@ -137,7 +151,7 @@
Table [SSDT](id 0005) - 14 Objects with 0 Devices 5 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0006) - 14 Objects with 1 Devices 2 Methods 0 Regions
- tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired
+ tbxface-0596 [00] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
@@ -145,24 +159,24 @@
lockdep: fixing up alternatives.
Booting processor 1/1 ip 6000
Initializing CPU#1
-Calibrating delay using timer specific routine.. 3657.57 BogoMIPS (lpj=7315141)
+Calibrating delay using timer specific routine.. 3657.62 BogoMIPS (lpj=7315256)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Intel Genuine Intel(R) CPU T2400 @ 1.83GHz stepping 08
checking TSC synchronization [CPU#0 -> CPU#1]:
-Measured 579986 cycles TSC warp between CPUs, turning off TSC clock.
-Marking TSC unstable due to: check_tsc_sync_source failed.
+Measured 579326 cycles TSC warp between CPUs, turning off TSC clock.
+Marking TSC unstable due to check_tsc_sync_source failed
Brought up 2 CPUs
-Total of 2 processors activated (7319.61 BogoMIPS).
+Total of 2 processors activated (7315.12 BogoMIPS).
CPU0 attaching sched-domain:
- domain 0: span 0-1
+ domain 0: span 0-1 level CPU
groups: 0 1
CPU1 attaching sched-domain:
- domain 0: span 0-1
+ domain 0: span 0-1 level CPU
groups: 1 0
-net_namespace: 548 bytes
+net_namespace: 680 bytes
NET: Registered protocol family 16
ACPI: ACPI Dock Station Driver
ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: found ejectable bay
@@ -170,29 +184,58 @@
ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: Is dependent on dock
ACPI: Bay [\_SB_.PCI0.IDE0.PRIM.MSTR] Added
+ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
PCI: MCFG area at f0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
-Setting up standard PCI resources
-evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
+evgpeblk-0957 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
ACPI: EC: EC description table is found, configuring boot EC
Completing Region/Field/Buffer/Package initialization:........................................................................................................................................................................................................................................................................
Initialized 28/28 Regions 126/126 Fields 54/54 Buffers 56/56 Packages (1651 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:...<6>ACPI: EC: non-query interrupt received, switching to interrupt mode
....
Executed 7 _INI methods requiring 2 _STA executions (examined 76 objects)
-evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 8 Wake, Enabled 2 Runtime GPEs in this block
+evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 8 Wake, Enabled 2 Runtime GPEs in this block
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
+pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
+pci 0000:00:1b.0: PME# disabled
+pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
+pci 0000:00:1c.0: PME# disabled
+pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
+pci 0000:00:1c.1: PME# disabled
+pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
+pci 0000:00:1c.2: PME# disabled
+pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
+pci 0000:00:1c.3: PME# disabled
+pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
+pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
-PCI: Transparent bridge - 0000:00:1e.0
+pci 0000:00:1f.2: PME# supported from D3hot
+pci 0000:00:1f.2: PME# disabled
+pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
+pci 0000:02:00.0: PME# disabled
+pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
+pci 0000:03:00.0: PME# disabled
+pci 0000:15:00.0: supports D1
+pci 0000:15:00.0: supports D2
+pci 0000:15:00.0: PME# supported from D0 D1 D2 D3hot D3cold
+pci 0000:15:00.0: PME# disabled
+pci 0000:15:00.1: PME# supported from D0 D3hot D3cold
+pci 0000:15:00.1: PME# disabled
+pci 0000:15:00.2: supports D1
+pci 0000:15:00.2: supports D2
+pci 0000:15:00.2: PME# supported from D0 D1 D2 D3hot D3cold
+pci 0000:15:00.2: PME# disabled
+pci 0000:00:1e.0: transparent bridge
+bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
@@ -219,7 +262,7 @@
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
-Bluetooth: Core ver 2.11
+Bluetooth: Core ver 2.12
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
@@ -230,11 +273,11 @@
system 00:00: iomem range 0xc8000-0xcbfff has been reserved
system 00:00: iomem range 0xcc000-0xcffff could not be reserved
system 00:00: iomem range 0xd0000-0xd3fff could not be reserved
-system 00:00: iomem range 0xdc000-0xdffff has been reserved
-system 00:00: iomem range 0xe0000-0xe3fff has been reserved
-system 00:00: iomem range 0xe4000-0xe7fff has been reserved
-system 00:00: iomem range 0xe8000-0xebfff has been reserved
-system 00:00: iomem range 0xec000-0xeffff has been reserved
+system 00:00: iomem range 0xdc000-0xdffff could not be reserved
+system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
+system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
+system 00:00: iomem range 0xe8000-0xebfff could not be reserved
+system 00:00: iomem range 0xec000-0xeffff could not be reserved
system 00:00: iomem range 0xf0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0x7fffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfed3ffff could not be reserved
@@ -250,38 +293,43 @@
system 00:02: iomem range 0xfed14000-0xfed17fff could not be reserved
system 00:02: iomem range 0xfed18000-0xfed18fff could not be reserved
system 00:02: iomem range 0xfed19000-0xfed19fff could not be reserved
-PCI: Bridge: 0000:00:1c.0
- IO window: 2000-2fff
- MEM window: 0xee000000-0xee0fffff
- PREFETCH window: disabled.
-PCI: Bridge: 0000:00:1c.1
- IO window: 3000-4fff
- MEM window: 0xec000000-0xedffffff
- PREFETCH window: 0x00000000e4000000-0x00000000e40fffff
-PCI: Bridge: 0000:00:1c.2
- IO window: 5000-6fff
- MEM window: 0xe8000000-0xe9ffffff
- PREFETCH window: 0x00000000e4100000-0x00000000e41fffff
-PCI: Bridge: 0000:00:1c.3
- IO window: 7000-8fff
- MEM window: 0xea000000-0xebffffff
- PREFETCH window: 0x00000000e4200000-0x00000000e42fffff
-PCI: Bus 22, cardbus bridge: 0000:15:00.0
- IO window: 0x00009000-0x000090ff
- IO window: 0x00009400-0x000094ff
- PREFETCH window: 0xe0000000-0xe3ffffff
- MEM window: 0x88000000-0x8bffffff
-PCI: Bridge: 0000:00:1e.0
- IO window: 9000-cfff
- MEM window: 0xe4300000-0xe7ffffff
- PREFETCH window: 0x00000000e0000000-0x00000000e3ffffff
-PCI: Setting latency timer of device 0000:00:1c.0 to 64
-PCI: Setting latency timer of device 0000:00:1c.1 to 64
-PCI: Setting latency timer of device 0000:00:1c.2 to 64
-PCI: Setting latency timer of device 0000:00:1c.3 to 64
+pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
+pci 0000:00:1c.0: IO window: 0x2000-0x2fff
+pci 0000:00:1c.0: MEM window: 0xee000000-0xee0fffff
+pci 0000:00:1c.0: PREFETCH window: disabled
+pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
+pci 0000:00:1c.1: IO window: 0x3000-0x4fff
+pci 0000:00:1c.1: MEM window: 0xec000000-0xedffffff
+pci 0000:00:1c.1: PREFETCH window: 0x000000e4000000-0x000000e40fffff
+pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
+pci 0000:00:1c.2: IO window: 0x5000-0x6fff
+pci 0000:00:1c.2: MEM window: 0xe8000000-0xe9ffffff
+pci 0000:00:1c.2: PREFETCH window: 0x000000e4100000-0x000000e41fffff
+pci 0000:00:1c.3: PCI bridge, secondary bus 0000:0c
+pci 0000:00:1c.3: IO window: 0x7000-0x8fff
+pci 0000:00:1c.3: MEM window: 0xea000000-0xebffffff
+pci 0000:00:1c.3: PREFETCH window: 0x000000e4200000-0x000000e42fffff
+pci 0000:15:00.0: CardBus bridge, secondary bus 0000:16
+pci 0000:15:00.0: IO window: 0x009000-0x0090ff
+pci 0000:15:00.0: IO window: 0x009400-0x0094ff
+pci 0000:15:00.0: PREFETCH window: 0xe0000000-0xe3ffffff
+pci 0000:15:00.0: MEM window: 0x88000000-0x8bffffff
+pci 0000:00:1e.0: PCI bridge, secondary bus 0000:15
+pci 0000:00:1e.0: IO window: 0x9000-0xcfff
+pci 0000:00:1e.0: MEM window: 0xe4300000-0xe7ffffff
+pci 0000:00:1e.0: PREFETCH window: 0x000000e0000000-0x000000e3ffffff
+pci 0000:00:1c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
+pci 0000:00:1c.0: setting latency timer to 64
+pci 0000:00:1c.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
+pci 0000:00:1c.1: setting latency timer to 64
+pci 0000:00:1c.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
+pci 0000:00:1c.2: setting latency timer to 64
+pci 0000:00:1c.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
+pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1e.0: enabling device (0005 -> 0007)
-PCI: Setting latency timer of device 0000:00:1e.0 to 64
-PCI: Setting latency timer of device 0000:15:00.0 to 64
+pci 0000:00:1e.0: setting latency timer to 64
+pci 0000:15:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
+pci 0000:15:00.0: setting latency timer to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
@@ -310,7 +358,7 @@
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 102x42
fb0: VESA VGA frame buffer device
-ACPI: AC Adapter [AC] (on-line)
+ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
@@ -325,21 +373,21 @@
Parsing all Control Methods:
Table [SSDT](id 0026) - 13 Objects with 0 Devices 1 Methods 0 Regions
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
-ACPI: ACPI0007:00 is registered as cooling_device0
+processor ACPI0007:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 7F6F1C5E, 00C8 (r1 PmRef Cpu1Ist 100 INTL 20050513)
Parsing all Control Methods:
-Table [SSDT](id 0030) - 4 Objects with 0 Devices 4 Methods 0 Regions
+Table [SSDT](id 002E) - 4 Objects with 0 Devices 4 Methods 0 Regions
ACPI: SSDT 7F6F1F66, 0085 (r1 PmRef Cpu1Cst 100 INTL 20050513)
Parsing all Control Methods:
-Table [SSDT](id 0031) - 1 Objects with 0 Devices 1 Methods 0 Regions
+Table [SSDT](id 002F) - 1 Objects with 0 Devices 1 Methods 0 Regions
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
-ACPI: ACPI0007:01 is registered as cooling_device1
+processor ACPI0007:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
-ACPI: LNXTHERM:01 is registered as thermal_zone0
-ACPI: Thermal Zone [THM0] (58 C)
-ACPI: LNXTHERM:02 is registered as thermal_zone1
-ACPI: Thermal Zone [THM1] (60 C)
+thermal LNXTHERM:01: registered as thermal_zone0
+ACPI: Thermal Zone [THM0] (50 C)
+thermal LNXTHERM:02: registered as thermal_zone1
+ACPI: Thermal Zone [THM1] (49 C)
lp: driver loaded but no devices found
Non-volatile memory driver v1.2
intel_rng: FWH not detected
@@ -349,16 +397,18 @@
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
[drm] Initialized drm 1.1.0 20060810
-PCI: Setting latency timer of device 0000:00:02.0 to 64
+pci 0000:00:02.0: power state changed by ACPI to D0
+pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
+pci 0000:00:02.0: setting latency timer to 64
[drm] Initialized i915 1.6.0 20060119 on minor 0
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets
intelfb: Version 0.9.5
intelfb: Cannot reserve FB region.
-Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
+Serial: 8250/16550 driver4 ports, IRQ sharing disabled
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
floppy0: no floppy controllers found
loop: module loaded
-thinkpad_acpi: ThinkPad ACPI Extras v0.20
+thinkpad_acpi: ThinkPad ACPI Extras v0.21
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS 7BETD3WW (2.14 ), EC 7BHT40WW-1.13
thinkpad_acpi: Lenovo ThinkPad X60, model 17097HU
@@ -380,7 +430,8 @@
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e1000e 0000:02:00.0: Disabling L1 ASPM
-PCI: Setting latency timer of device 0000:02:00.0 to 64
+e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
+e1000e 0000:02:00.0: setting latency timer to 64
eth0: (PCI Express:2.5GB/s:Width x1) 00:16:d3:25:19:04
eth0: Intel(R) PRO/1000 Network Connection
eth0: MAC: 2, PHY: 2, PBA No: 005302-003
@@ -408,17 +459,18 @@
usbcore: registered new interface driver w35und
iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26kds
iwl3945: Copyright(c) 2003-2008 Intel Corporation
-PCI: Setting latency timer of device 0000:03:00.0 to 64
+iwl3945 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
+iwl3945 0000:03:00.0: setting latency timer to 64
iwl3945: Detected Intel Wireless WiFi Link 3945ABG
iwl3945: Tunable channels: 11 802.11bg, 13 802.11a channels
phy0: Selected rate control algorithm 'iwl-3945-rs'
-ACPI: PCI interrupt for device 0000:03:00.0 disabled
+iwl3945 0000:03:00.0: PCI INT A disabled
Linux video capture interface: v2.00
Uniform Multi-Platform E-IDE driver
-ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
-ICH7: IDE controller (0x8086:0x27df rev 0x02) at PCI slot 0000:00:1f.1
-ICH7: not 100% native mode: will probe irqs later
-ICH7: IDE port disabled
+piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x02)
+pci 0000:00:1f.1: PCI INT C -> GSI 16 (level, low) -> IRQ 16
+piix 0000:00:1f.1: IDE port disabled
+piix 0000:00:1f.1: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817
Probing IDE interface ide0...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
@@ -426,9 +478,10 @@
ide_generic: I/O resource 0x1F0-0x1F7 not free.
ide_generic: I/O resource 0x170-0x177 not free.
ahci 0000:00:1f.2: version 3.0
+ahci 0000:00:1f.2: PCI INT B -> GSI 16 (level, low) -> IRQ 16
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x1 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
-PCI: Setting latency timer of device 0000:00:1f.2 to 64
+ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
ahci: autosuspend disabled
scsi1 : ahci
@@ -437,7 +490,7 @@
ahci: autosuspend disabled
scsi3 : ahci
ahci: autosuspend disabled
-ata1: SATA max UDMA/133 abar m1024@0xee444400 port 0xee444500 irq 16
+ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 16
ata2: DUMMY
ata3: DUMMY
ata4: DUMMY
@@ -471,11 +524,13 @@
pcmcia: parent PCI bridge I/O window: 0x9000 - 0xcfff
pcmcia: parent PCI bridge Memory window: 0xe4300000 - 0xe7ffffff
pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xe3ffffff
-PCI: Setting latency timer of device 0000:00:1d.7 to 64
+ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
+ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
+ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
-PCI: cache line size of 32 is not supported by device 0000:00:1d.7
+ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xee444000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
@@ -484,11 +539,13 @@
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
-usb usb1: Manufacturer: Linux 2.6.26 ehci_hcd
+usb usb1: Manufacturer: Linux 2.6.27-rc2 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
-PCI: Setting latency timer of device 0000:00:1d.0 to 64
+uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
+uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
+uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001820
@@ -498,9 +555,10 @@
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
-usb usb2: Manufacturer: Linux 2.6.26 uhci_hcd
+usb usb2: Manufacturer: Linux 2.6.27-rc2 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
-PCI: Setting latency timer of device 0000:00:1d.1 to 64
+uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
+uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 17, io base 0x00001840
@@ -510,9 +568,11 @@
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
-usb usb3: Manufacturer: Linux 2.6.26 uhci_hcd
+usb usb3: Manufacturer: Linux 2.6.27-rc2 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
-PCI: Setting latency timer of device 0000:00:1d.2 to 64
+uhci_hcd 0000:00:1d.2: power state changed by ACPI to D0
+uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
+uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
@@ -522,9 +582,10 @@
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
-usb usb4: Manufacturer: Linux 2.6.26 uhci_hcd
+usb usb4: Manufacturer: Linux 2.6.27-rc2 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
-PCI: Setting latency timer of device 0000:00:1d.3 to 64
+uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
+uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 19, io base 0x00001880
@@ -534,7 +595,7 @@
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
-usb usb5: Manufacturer: Linux 2.6.26 uhci_hcd
+usb usb5: Manufacturer: Linux 2.6.27-rc2 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
usb 5-1: new full speed USB device using uhci_hcd and address 2
usb 5-1: configuration #1 chosen from 1 choice
@@ -562,31 +623,34 @@
input: PC Speaker as /class/input/input5
input: PS/2 Generic Mouse as /class/input/input6
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
-rtc0: alarms up to one month, y3k
+rtc0: alarms up to one month, y3k, hpet irqs
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
-device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx
+device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@xxxxxxxxxx
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: Generic Bluetooth USB driver ver 0.1
usbcore: registered new interface driver btusb
-EDAC MC: Ver: 2.1.0 Jul 14 2008
+EDAC MC: Ver: 2.1.0 Aug 6 2008
cpuidle: using governor ladder
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
-sdhci: SDHCI controller found at 0000:15:00.2 [1180:0822] (rev 18)
-mmc0: Will use DMA mode even though HW doesn't fully claim to support it.
-PCI: Setting latency timer of device 0000:15:00.2 to 64
+sdhci-pci 0000:15:00.2: SDHCI controller found [1180:0822] (rev 18)
+sdhci-pci 0000:15:00.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
Registered led device: mmc0
-mmc0: SDHCI at 0xe4301800 irq 18 DMA
+mmc0: SDHCI controller on PCI [0000:15:00.2] using PIO
ricoh-mmc: Ricoh MMC Controller disabling driver
ricoh-mmc: Copyright(c) Philip Langdale
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
-Advanced Linux Sound Architecture Driver Version 1.0.16.
+Advanced Linux Sound Architecture Driver Version 1.0.17.
+HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
hda_intel: probe_mask set to 0x1 for device 17aa:2010
-PCI: Setting latency timer of device 0000:00:1b.0 to 64
+HDA Intel 0000:00:1b.0: setting latency timer to 64
+mmc0: new MMC card at address 0001
+mmcblk0: mmc0:0001 MMC 1019392KiB
+ mmcblk0: p1
usbcore: registered new interface driver snd-usb-audio
ALSA device list:
#0: HDA Intel at 0xee240000 irq 17
@@ -594,26 +658,23 @@
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
-Bluetooth: L2CAP ver 2.9
+Bluetooth: L2CAP ver 2.10
Bluetooth: L2CAP socket layer initialized
-Bluetooth: SCO (Voice Link) ver 0.5
+Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
-Bluetooth: RFCOMM ver 1.8
+Bluetooth: RFCOMM ver 1.10
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
-mmc0: new MMC card at address 0001
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@xxxxxxxxxxxxxxx>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
-mmcblk0: mmc0:0001 MMC 1019392KiB
- mmcblk0:<6>Installing 9P2000 support
- p1
+Installing 9P2000 support
Using IPI No-Shortcut mode
PM: Resume from partition /dev/sda1
PM: Checking hibernation image.
@@ -625,9 +686,9 @@
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
-debug: unmapping init memory c09a1000..c09f1000
-Write protecting the kernel text: 5324k
-Write protecting the kernel read-only data: 1916k
+debug: unmapping init memory c09cb000..c0a21000
+Write protecting the kernel text: 5440k
+Write protecting the kernel read-only data: 1968k
Failed to execute /tmp/swsusp-init. Attempting defaults...
EXT3 FS on sda4, internal journal
Adding 987988k swap on /dev/sda1. Priority:-1 extents:1 across:987988k
@@ -637,10 +698,259 @@
pcmcia: Detected deprecated PCMCIA ioctl usage from process: hwclock.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
-Clocksource tsc unstable (delta = -82296647 ns)
-eth0: Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
coda_read_super: Bad mount data
coda_read_super: device index: 0
coda_read_super: rootfid is (01234567.ffffffff.08051a38.00000000)
coda: Unexpected interruption.
Failure of coda_cnode_make for root: error -4
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
--
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
