Tejun Heo a écrit :
> Rafael J. Wysocki wrote:
>
>> [Adding CCs.]
>>
>> On Tuesday, 1 of July 2008, Mathieu Bérard wrote:
>>
>>> Hi,
>>> I have a laptop with an ICH6M SATA Controller and a Hitachi hard drive.
>>> While it worked well using the ahci module and Linux 2.6.25,
>>> it get randomly 'stuck' for several seconds to several minutes with 2.6.26-rc8.
>>> Successive errors progressively reduce the ATA link speed.
>>>
>>> Passing the libata.noacpi parameter is an effective workaround.
>>>
>>> Please note that it's not the first time i have this kind of issue, see:
>>> http://marc.info/?l=linux-ide&m=117305595312399&w=2
>>> This was found to be a bad interaction between my _GTF taskfile, which enable the
>>> "Enable Device-Initiated Interface Power State Transitions" feature, and NCQ.
>>> The driver was later NCQ blacklisted to correct the problem.
>>>
>
> Can you please post the result of "hdparm -I /dev/sda" and full kernel
> boot log? 0xca is not a NCQ command so the it's not related to NCQ at
> all. It seems we'll need to filter out DIPM commands from _GTF.
>
>
Hi,
hdparm and dmesg output attached.
I was not expecting anything related to NCQ as my drive is blacklisted,
I was just mentioning previous issue with that hardware.
Do you know what has changed in this version that is now causing failure
with DIPM ? I could bisect to try to find out, but this will be painful
as the
device hang may only appears after several minutes of disk activity.
--
Mathieu
/dev/sda:
ATA device, with non-removable media
Model Number: HTS541010G9SA00
Serial Number: MP2ZM4X0GSWJKR
Firmware Revision: MBZOC60D
Standards:
Used: ATA/ATAPI-7 T13 1532D revision 1
Supported: 7 6 5 4
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 195371568
LBA48 user addressable sectors: 195371568
device size with M = 1024*1024: 95396 MBytes
device size with M = 1000*1000: 100030 MBytes (100 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Vendor, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Advanced power management level: 128
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* IDLE_IMMEDIATE with UNLOAD
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
Non-Zero buffer offsets in DMA Setup FIS
DMA Setup Auto-Activate optimization
Device-initiated interface power management
In-order data delivery
* Software settings preservation
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
64min for SECURITY ERASE UNIT.
Checksum: correct
[ 0.000000] Linux version 2.6.26-rc8 (mathieu@manwe) (gcc version 4.3.1 (Ubuntu 4.3.1-3ubuntu1) ) #1 PREEMPT Mon Jun 30 01:12:00 CEST 2008
[ 0.000000] PAT disabled. Not yet verified on this CPU type.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fee0000 (usable)
[ 0.000000] BIOS-e820: 000000003fee0000 - 000000003feea000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003feea000 - 000000003ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] 126MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] Entering add_active_range(0, 0, 261856) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 261856
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 261856
[ 0.000000] On node 0 totalpages: 261856
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 254 pages used for memmap
[ 0.000000] HighMem zone: 32226 pages, LIFO batch:7
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F6950, 0014 (r0 TOSCPL)
[ 0.000000] ACPI: RSDT 3FEE1FCA, 0044 (r1 TOSCPL RSDT 6040000 LTP 0)
[ 0.000000] ACPI: APIC 3FEE9E88, 0068 (r1 INTEL ALVISO 6040000 LOHR 5F)
[ 0.000000] ACPI: FACP 3FEE9EF0, 0074 (r1 TOSCPL ALVISO 6040000 LOHR 32)
[ 0.000000] ACPI: DSDT 3FEE2A72, 7416 (r1 TOSCPL ALVISO 6040000 MSFT 3000000)
[ 0.000000] ACPI: FACS 3FEFAFC0, 0040
[ 0.000000] ACPI: BOOT 3FEE9FD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: MCFG 3FEE9F9C, 003C (r1 INTEL ALVISO 6040000 LOHR 5F)
[ 0.000000] ACPI: SSDT 3FEE2840, 022E (r1 SataRe SataAhci 1000 INTL 20030224)
[ 0.000000] ACPI: SSDT 3FEE2405, 022B (r1 PmRef Cpu0Ist 3000 INTL 20030224)
[ 0.000000] ACPI: SSDT 3FEE2227, 01DE (r1 PmRef Cpu0Cst 3001 INTL 20030224)
[ 0.000000] ACPI: SSDT 3FEE200E, 0219 (r1 PmRef CpuPm 3000 INTL 20030224)
[ 0.000000] ACPI: DMI detected: Toshiba
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
[ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
[ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259810
[ 0.000000] Kernel command line: root=UUID=8aa84942-b9a7-4622-a512-c180ce3095db ro savedefault single
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Preemptible RCU implementation.
[ 0.000000] CPU 0 irqstacks, hard=c03b8000 soft=c03b7000
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1729.103 MHz processor.
[ 0.000999] Console: colour VGA+ 80x25
[ 0.000999] console [tty0] enabled
[ 0.000999] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000999] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000999] Memory: 1030072k/1047424k available (1773k kernel code, 16608k reserved, 799k data, 188k init, 129920k highmem)
[ 0.000999] virtual kernel memory layout:
[ 0.000999] fixmap : 0xfffa8000 - 0xfffff000 ( 348 kB)
[ 0.000999] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.000999] vmalloc : 0xf8800000 - 0xff9fe000 ( 113 MB)
[ 0.000999] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.000999] .init : 0xc0385000 - 0xc03b4000 ( 188 kB)
[ 0.000999] .data : 0xc02bb5f8 - 0xc0383538 ( 799 kB)
[ 0.000999] .text : 0xc0100000 - 0xc02bb5f8 (1773 kB)
[ 0.000999] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.000999] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.061050] Calibrating delay using timer specific routine.. 3460.32 BogoMIPS (lpj=1730163)
[ 0.061163] Mount-cache hash table entries: 512
[ 0.061341] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.061427] CPU: L2 cache: 2048K
[ 0.061476] Intel machine check architecture supported.
[ 0.061529] Intel machine check reporting enabled on CPU#0.
[ 0.061586] CPU: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
[ 0.061711] Checking 'hlt' instruction... OK.
[ 0.065337] Freeing SMP alternatives: 0k freed
[ 0.065387] ACPI: Core revision 20080321
[ 0.077988] ENABLING IO-APIC IRQs
[ 0.077988] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.087986] net_namespace: 480 bytes
[ 0.087986] NET: Registered protocol family 16
[ 0.087986] ACPI: bus type pci registered
[ 0.087986] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.087986] PCI: MCFG area at e0000000 reserved in E820
[ 0.087986] PCI: Using MMCONFIG for extended config space
[ 0.087986] PCI: Using configuration type 1 for base access
[ 0.087986] Setting up standard PCI resources
[ 0.092423] ACPI: EC: Look up EC in DSDT
[ 0.095508] ACPI: Interpreter enabled
[ 0.095558] ACPI: (supports S0 S3 S4 S5)
[ 0.095759] ACPI: Using IOAPIC for interrupt routing
[ 0.140766] ACPI: EC: GPE = 0x1d, I/O: command/status = 0x66, data = 0x62
[ 0.140822] ACPI: EC: driver started in poll mode
[ 0.140891] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.141686] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.141693] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.141757] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 0.142803] PCI: Transparent bridge - 0000:00:1e.0
[ 0.142908] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.143252] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[ 0.143413] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.143566] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.143730] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.150741] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.151338] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.151970] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.152604] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.153196] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.153830] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.154422] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.154976] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.155634] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.155696] pnp: PnP ACPI init
[ 0.155747] ACPI: bus type pnp registered
[ 0.178303] pnp: PnP ACPI: found 9 devices
[ 0.178353] ACPI: ACPI bus type pnp unregistered
[ 0.178449] PCI: Using ACPI for IRQ routing
[ 0.182234] hpet clockevent registered
[ 0.182241] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.182433] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.189107] system 00:01: ioport range 0xfe00-0xfe7f has been reserved
[ 0.189163] system 00:01: ioport range 0xfe80-0xfeff has been reserved
[ 0.189217] system 00:01: ioport range 0xff00-0xff7f has been reserved
[ 0.189272] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.189334] system 00:01: iomem range 0xf0000000-0xf0003fff could not be reserved
[ 0.189395] system 00:01: iomem range 0xf0004000-0xf0004fff could not be reserved
[ 0.189457] system 00:01: iomem range 0xf0005000-0xf0005fff could not be reserved
[ 0.189519] system 00:01: iomem range 0xf0008000-0xf000bfff could not be reserved
[ 0.189581] system 00:01: iomem range 0xfed20000-0xfed8ffff could not be reserved
[ 0.189651] system 00:05: ioport range 0x800-0x80f has been reserved
[ 0.189705] system 00:05: ioport range 0x1000-0x107f has been reserved
[ 0.189758] system 00:05: ioport range 0x1180-0x11bf has been reserved
[ 0.189812] system 00:05: ioport range 0x1640-0x164f has been reserved
[ 0.219963] PCI: region 0000:06:04.0/9 too large: 0x0000000000000000-0x0000000003ffffff
[ 0.220032] PCI: Bridge: 0000:00:01.0
[ 0.220080] IO window: 3000-3fff
[ 0.220129] MEM window: 0xb8100000-0xb81fffff
[ 0.220181] PREFETCH window: 0x00000000c8000000-0x00000000cfffffff
[ 0.220236] PCI: Bridge: 0000:00:1c.0
[ 0.220285] IO window: 4000-4fff
[ 0.220336] MEM window: 0xbc000000-0xbfffffff
[ 0.220389] PREFETCH window: 0x00000000d0000000-0x00000000d3ffffff
[ 0.220447] PCI: Bridge: 0000:00:1c.1
[ 0.220496] IO window: 5000-5fff
[ 0.220547] MEM window: 0xc0000000-0xc3ffffff
[ 0.220600] PREFETCH window: 0x00000000d4000000-0x00000000d7ffffff
[ 0.220661] PCI: Bus 7, cardbus bridge: 0000:06:04.0
[ 0.220711] IO window: 0x00006400-0x000064ff
[ 0.220763] IO window: 0x00006800-0x000068ff
[ 0.220816] MEM window: 0x50000000-0x53ffffff
[ 0.220869] PCI: Bridge: 0000:00:1e.0
[ 0.220918] IO window: 6000-6fff
[ 0.220970] MEM window: 0xc4000000-0xc40fffff
[ 0.221023] PREFETCH window: disabled.
[ 0.221086] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.221185] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.221205] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.221305] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.221326] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[ 0.221425] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.221438] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.221454] ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.221559] NET: Registered protocol family 2
[ 0.239044] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.239958] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.240787] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.241114] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.241169] TCP reno registered
[ 0.247066] NET: Registered protocol family 1
[ 0.247241] Unpacking initramfs... done
[ 0.479151] Freeing initrd memory: 4484k freed
[ 0.479252] Simple Boot Flag at 0x36 set to 0x1
[ 0.479684] highmem bounce pool size: 64 pages
[ 0.479743] Total HugeTLB memory allocated, 0
[ 0.480987] msgmni has been set to 1767
[ 0.481151] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.481214] io scheduler noop registered
[ 0.481270] io scheduler cfq registered (default)
[ 0.481425] pci 0000:01:00.0: Boot video device
[ 0.481507] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.481535] assign_interrupt_mode Found MSI capability
[ 0.481610] Allocate Port Service[0000:00:01.0:pcie00]
[ 0.481628] Allocate Port Service[0000:00:01.0:pcie03]
[ 0.481675] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.481716] assign_interrupt_mode Found MSI capability
[ 0.481806] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.481820] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.481833] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.481915] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.481956] assign_interrupt_mode Found MSI capability
[ 0.482045] Allocate Port Service[0000:00:1c.1:pcie00]
[ 0.482060] Allocate Port Service[0000:00:1c.1:pcie02]
[ 0.482073] Allocate Port Service[0000:00:1c.1:pcie03]
[ 0.483062] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.483403] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.483522] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.483575] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.483627] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.483678] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.483730] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.483796] mice: PS/2 mouse device common for all mice
[ 0.483867] cpuidle: using governor ladder
[ 0.483919] cpuidle: using governor menu
[ 0.484282] TCP cubic registered
[ 0.484331] Using IPI Shortcut mode
[ 0.484418] registered taskstats version 1
[ 0.484726] Freeing unused kernel memory: 188k freed
[ 0.487357] input: AT Translated Set 2 keyboard as /class/input/input0
[ 0.552083] No dock devices found.
[ 0.558425] SCSI subsystem initialized
[ 0.566002] libata version 3.00 loaded.
[ 0.567684] ahci 0000:00:1f.2: version 3.0
[ 0.567713] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 0.682859] Switched to high resolution mode on CPU 0
[ 1.568027] ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0x5 impl IDE mode
[ 1.568091] ahci 0000:00:1f.2: flags: 64bit ncq pm led slum part
[ 1.568146] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 1.568283] scsi0 : ahci
[ 1.568398] scsi1 : ahci
[ 1.568482] scsi2 : ahci
[ 1.568568] scsi3 : ahci
[ 1.568695] ata1: SATA max UDMA/133 abar m1024@0xb8000c00 port 0xb8000d00 irq 19
[ 1.568756] ata2: DUMMY
[ 1.568803] ata3: SATA max UDMA/133 abar m1024@0xb8000c00 port 0xb8000e00 irq 19
[ 1.568864] ata4: DUMMY
[ 1.873016] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.874045] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1.875000] ata1.00: ATA-7: HTS541010G9SA00, MBZOC60D, max UDMA/100
[ 1.875000] ata1.00: 195371568 sectors, multi 0: LBA48 NCQ (not used)
[ 1.875000] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1.875000] ata1.00: configured for UDMA/100
[ 2.205015] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.227086] scsi 0:0:0:0: Direct-Access ATA HTS541010G9SA00 MBZO PQ: 0 ANSI: 5
[ 2.233881] fuse init (API version 7.9)
[ 2.252219] device-mapper: uevent: version 1.0.3
[ 2.252347] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx
[ 2.520087] usbcore: registered new interface driver usbfs
[ 2.520163] usbcore: registered new interface driver hub
[ 2.520470] usbcore: registered new device driver usb
[ 2.521427] USB Universal Host Controller Interface driver v3.0
[ 2.521525] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.521630] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.521634] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.521771] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 2.521863] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
[ 2.521984] usb usb1: configuration #1 chosen from 1 choice
[ 2.522064] hub 1-0:1.0: USB hub found
[ 2.522116] hub 1-0:1.0: 2 ports detected
[ 2.562082] 8139too Fast Ethernet driver 0.9.28
[ 2.623248] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.623368] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.623372] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.623444] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 2.627410] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.627465] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.627472] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb8000000
[ 2.637010] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.637157] usb usb2: configuration #1 chosen from 1 choice
[ 2.637237] hub 2-0:1.0: USB hub found
[ 2.637291] hub 2-0:1.0: 8 ports detected
[ 2.738128] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 2.738240] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.738244] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.738317] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 2.738406] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[ 2.738536] usb usb3: configuration #1 chosen from 1 choice
[ 2.738614] hub 3-0:1.0: USB hub found
[ 2.738667] hub 3-0:1.0: 2 ports detected
[ 2.815997] ata_piix 0000:00:1f.1: version 2.12
[ 2.815997] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 2.815997] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 2.815997] scsi4 : ata_piix
[ 2.815997] scsi5 : ata_piix
[ 2.840100] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18c0 irq 14
[ 2.840157] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18c8 irq 15
[ 2.994584] ata5.00: ATAPI: MATSHITADVD-RAM UJ-841S, 1.50, max UDMA/33
[ 3.000504] ata5.00: configured for UDMA/33
[ 3.000582] ata6: port disabled. ignoring.
[ 3.002000] scsi 4:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-841S 1.50 PQ: 0 ANSI: 5
[ 3.002001] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 3.002001] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 3.002001] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.002001] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 3.002001] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[ 3.003055] usb usb4: configuration #1 chosen from 1 choice
[ 3.003132] hub 4-0:1.0: USB hub found
[ 3.003184] hub 4-0:1.0: 2 ports detected
[ 3.103998] ACPI: PCI Interrupt 0000:06:04.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 3.103998] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[ 3.103998] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 3.103998] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 3.103998] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 3.103998] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[ 3.103998] usb usb5: configuration #1 chosen from 1 choice
[ 3.105031] hub 5-0:1.0: USB hub found
[ 3.105084] hub 5-0:1.0: 2 ports detected
[ 3.160006] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 3.161007] firewire_ohci: Added fw-ohci device 0000:06:04.2, OHCI version 1.10
[ 3.161120] ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 3.161820] eth0: RealTek RTL8139 at 0xf88da000, 00:0f:b0:a5:9a:81, IRQ 21
[ 3.161874] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 3.211688] Driver 'sd' needs updating - please use bus_type methods
[ 3.211834] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 3.211901] sd 0:0:0:0: [sda] Write Protect is off
[ 3.211952] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.211973] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.212086] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 3.212154] sd 0:0:0:0: [sda] Write Protect is off
[ 3.212206] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.212228] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.212295] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 3.300999] usb 1-1: configuration #1 chosen from 1 choice
[ 3.343274] usbcore: registered new interface driver hiddev
[ 3.358385] input: Logitech USB Receiver as /class/input/input1
[ 3.363033] input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1
[ 3.393030] input: Logitech USB Receiver as /class/input/input2
[ 3.398051] input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1
[ 3.398339] usbcore: registered new interface driver usbhid
[ 3.398392] usbhid: v2.6:USB HID core driver
[ 3.591462] sda1 sda2 < sda5 sda6 > sda3
[ 3.608998] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.629031] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 3.629031] Uniform CD-ROM driver Revision: 3.20
[ 3.629031] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 3.632962] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.633040] sr 4:0:0:0: Attached scsi generic sg1 type 5
[ 3.661086] firewire_core: created device fw0: GUID 00023f5b8140757f, S400
[ 4.122469] PM: Starting manual resume from disk
[ 4.130170] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 4.132481] Filesystem "dm-0": Disabling barriers, not supported by the underlying device
[ 4.132729] XFS mounting filesystem dm-0
[ 4.214681] Ending clean XFS mount for filesystem: dm-0
[ 8.611728] Linux agpgart interface v0.103
[ 8.626735] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 8.626874] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[ 8.626957] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 8.709000] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[ 8.709262] ACPI: ACPI0007:00 is registered as cooling_device0
[ 8.709317] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 8.725918] input: Power Button (FF) as /class/input/input3
[ 8.752060] ACPI: Power Button (FF) [PWRF]
[ 8.752177] input: Lid Switch as /class/input/input4
[ 8.764121] ACPI: Lid Switch [LID0]
[ 8.764225] input: Power Button (CM) as /class/input/input5
[ 8.788047] ACPI: Power Button (CM) [PWRB]
[ 9.173654] ieee80211_crypt: registered algorithm 'NULL'
[ 9.270000] Marking TSC unstable due to: TSC halts in idle.
[ 9.414207] ACPI: AC Adapter [ACAD] (on-line)
[ 9.667778] ACPI: Battery Slot [BAT1] (battery present)
[ 9.689219] sdhci: Secure Digital Host Controller Interface driver
[ 9.689279] sdhci: Copyright(c) Pierre Ossman
[ 9.689359] sdhci: SDHCI controller found at 0000:06:04.4 [104c:8034] (rev 0)
[ 9.689432] ACPI: PCI Interrupt 0000:06:04.4[D] -> GSI 19 (level, low) -> IRQ 19
[ 9.689551] mmc0: Will use DMA mode even though HW doesn't fully claim to support it.
[ 9.689712] mmc0: SDHCI at 0xc4009400 irq 19 DMA
[ 9.689772] mmc1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 9.689862] mmc1: SDHCI at 0xc4009000 irq 19 DMA
[ 9.689921] mmc2: Will use DMA mode even though HW doesn't fully claim to support it.
[ 9.690021] mmc2: SDHCI at 0xc4006400 irq 19 DMA
[ 9.744484] input: PC Speaker as /class/input/input6
[ 9.751333] Real Time Clock Driver v1.12ac
[ 9.769279] ACPI: PCI Interrupt 0000:06:04.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 9.782047] input: Video Bus as /class/input/input7
[ 9.800258] Yenta: CardBus bridge found at 0000:06:04.0 [1179:ff00]
[ 9.800339] PCI: Bus 7, cardbus bridge: 0000:06:04.0
[ 9.800390] IO window: 0x00006400-0x000064ff
[ 9.800443] IO window: 0x00006800-0x000068ff
[ 9.800496] PREFETCH window: 0x54000000-0x543fffff
[ 9.800550] MEM window: 0x50000000-0x53ffffff
[ 9.800605] Yenta: Enabling burst memory read transactions
[ 9.800660] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 9.800712] Yenta: Routing CardBus interrupts to PCI
[ 9.800766] Yenta TI: socket 0000:06:04.0, mfunc 0x10aa1b22, devctl 0x66
[ 9.805070] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 9.805445] input: Video Bus as /class/input/input8
[ 9.816499] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 9.816558] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@xxxxxxxxxxxxxxx>
[ 9.829066] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
[ 9.840479] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 9.840547] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 10.023833] Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
[ 10.023892] Socket status: 30000006
[ 10.023942] Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a
[ 10.024005] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 10.024072] pcmcia: parent PCI bridge Memory window: 0xc4000000 - 0xc40fffff
[ 10.031338] input: PS/2 Mouse as /class/input/input9
[ 10.034886] ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 10.044815] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 10.044913] firmware: requesting ipw2200-bss.fw
[ 10.067714] input: AlpsPS/2 ALPS GlidePoint as /class/input/input10
[ 10.534594] ipw2200: Radio Frequency Kill Switch is On:
[ 10.534597] Kill switch must be turned off for wireless networking to work.
[ 10.535092] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
[ 10.535210] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 17
[ 10.535334] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 11.182157] Clocksource tsc unstable (delta = -77135590 ns)
[ 11.350030] intel8x0_measure_ac97_clock: measured 50736 usecs
[ 11.350082] intel8x0: clocking to 48000
[ 12.172322] Non-volatile memory driver v1.2
[ 12.185343] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
[ 12.190783] firmware: requesting intel-ucode/06-0d-08
[ 12.217045] IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
[ 12.229021] Machine check exception polling timer started.
[ 12.286418] Adding 1461844k swap on /dev/sda5. Priority:-1 extents:1 across:1461844k
[ 12.523578] Filesystem "dm-0": Disabling barriers, not supported by the underlying device
[ 12.939611] kjournald starting. Commit interval 5 seconds
[ 12.945052] EXT3 FS on sda1, internal journal
[ 12.945052] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.977320] Filesystem "dm-3": Disabling barriers, not supported by the underlying device
[ 12.997772] XFS mounting filesystem dm-3
[ 13.098262] Ending clean XFS mount for filesystem: dm-3
[ 13.143503] Filesystem "dm-1": Disabling barriers, not supported by the underlying device
[ 13.163812] XFS mounting filesystem dm-1
[ 13.237413] Ending clean XFS mount for filesystem: dm-1
[ 13.238065] Filesystem "dm-2": Disabling barriers, not supported by the underlying device
[ 13.238211] XFS mounting filesystem dm-2
[ 13.452498] Ending clean XFS mount for filesystem: dm-2
[ 17.686089] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 23.810166] usb 2-5: new high speed USB device using ehci_hcd and address 3
[ 23.925029] usb 2-5: configuration #1 chosen from 1 choice
[ 23.963473] Initializing USB Mass Storage driver...
[ 23.964288] scsi6 : SCSI emulation for USB Mass Storage devices
[ 23.964454] usbcore: registered new interface driver usb-storage
[ 23.964457] USB Mass Storage support registered.
[ 23.965619] usb-storage: device found at 3
[ 23.965621] usb-storage: waiting for device to settle before scanning
[ 24.565378] NET: Registered protocol family 17
[ 26.130297] atkbd.c: Unknown key pressed (translated set 2, code 0x95 on isa0060/serio0).
[ 26.130297] atkbd.c: Use 'setkeycodes e015 <keycode>' to make it known.
[ 26.130462] atkbd.c: Unknown key released (translated set 2, code 0x95 on isa0060/serio0).
[ 26.130462] atkbd.c: Use 'setkeycodes e015 <keycode>' to make it known.
[ 26.247963] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 28.965258] usb-storage: device scan complete
[ 28.965597] scsi 6:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2
[ 28.978447] sd 6:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB)
[ 28.982239] sd 6:0:0:0: [sdb] Write Protect is off
[ 28.982243] sd 6:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 28.982245] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 28.984431] sd 6:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB)
[ 28.985075] sd 6:0:0:0: [sdb] Write Protect is off
[ 28.985075] sd 6:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 28.985075] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 28.985075] sdb: sdb1
[ 28.985840] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 28.985840] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 105.379430] tun: Universal TUN/TAP device driver, 1.6
[ 105.379435] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
[ 332.992622] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 499.178040] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 499.178105] ata1.00: cmd ca/00:3e:76:45:81/00:00:00:00:00/e1 tag 0 dma 31744 out
[ 499.178106] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 499.178168] ata1.00: status: { DRDY }
[ 499.178220] ata1: hard resetting link
[ 499.942034] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 499.943540] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 499.946056] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 499.947174] ata1.00: configured for UDMA/100
[ 499.947174] ata1: EH complete
[ 499.947443] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 499.947443] sd 0:0:0:0: [sda] Write Protect is off
[ 499.947443] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 499.947443] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 529.963038] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 529.963102] ata1.00: cmd ca/00:18:17:0b:94/00:00:00:00:00/e0 tag 0 dma 12288 out
[ 529.963103] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 529.963166] ata1.00: status: { DRDY }
[ 529.963217] ata1: hard resetting link
[ 530.778173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 530.779373] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 530.781865] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 530.782983] ata1.00: configured for UDMA/100
[ 530.782983] ata1: EH complete
[ 530.784112] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 530.784232] sd 0:0:0:0: [sda] Write Protect is off
[ 530.784235] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 530.784474] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 560.791039] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 560.791104] ata1.00: cmd ca/00:28:1f:7f:99/00:00:00:00:00/e0 tag 0 dma 20480 out
[ 560.791106] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 560.791168] ata1.00: status: { DRDY }
[ 560.791219] ata1: hard resetting link
[ 561.606033] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 561.607234] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 561.609720] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 561.610838] ata1.00: configured for UDMA/100
[ 561.610838] ata1: EH complete
[ 561.611190] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 561.611354] sd 0:0:0:0: [sda] Write Protect is off
[ 561.611354] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 561.612087] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 682.780718] ieee80211_crypt: registered algorithm 'CCMP'
[ 683.768096] ieee80211_crypt: registered algorithm 'TKIP'
[ 814.838039] ata1: limiting SATA link speed to 1.5 Gbps
[ 814.838046] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 814.838109] ata1.00: cmd ca/00:10:57:b6:17/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 814.838110] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 814.838172] ata1.00: status: { DRDY }
[ 814.838224] ata1: hard resetting link
[ 815.602032] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 815.603229] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 815.606466] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 815.607598] ata1.00: configured for UDMA/100
[ 815.607598] ata1: EH complete
[ 815.607806] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 815.607887] sd 0:0:0:0: [sda] Write Protect is off
[ 815.607887] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 815.608242] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 845.624027] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 845.624087] ata1.00: cmd ca/00:10:df:17:79/00:00:00:00:00/e0 tag 0 dma 8192 out
[ 845.624089] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 845.624150] ata1.00: status: { DRDY }
[ 845.624199] ata1: hard resetting link
[ 846.439166] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 846.440368] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 846.442863] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 846.443980] ata1.00: configured for UDMA/100
[ 846.443980] ata1: EH complete
[ 846.444412] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 846.444783] sd 0:0:0:0: [sda] Write Protect is off
[ 846.444783] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 846.444977] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 876.459037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 876.459103] ata1.00: cmd ca/00:01:87:08:71/00:00:00:00:00/e3 tag 0 dma 512 out
[ 876.459105] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 876.459166] ata1.00: status: { DRDY }
[ 876.459218] ata1: hard resetting link
[ 877.325032] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 877.326233] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 877.329234] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 877.330350] ata1.00: configured for UDMA/100
[ 877.330350] ata1: EH complete
[ 877.334027] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 877.334086] sd 0:0:0:0: [sda] Write Protect is off
[ 877.334089] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 877.334125] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 970.438986] usb 2-5: USB disconnect, address 3
[ 1154.161035] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1154.161100] ata1.00: cmd ca/00:30:2f:19:f6/00:00:00:00:00/e2 tag 0 dma 24576 out
[ 1154.161102] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1154.161164] ata1.00: status: { DRDY }
[ 1154.161215] ata1: hard resetting link
[ 1154.772159] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1154.773358] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1154.775851] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1154.776967] ata1.00: configured for UDMA/100
[ 1154.776967] ata1: EH complete
[ 1154.777379] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1154.777571] sd 0:0:0:0: [sda] Write Protect is off
[ 1154.777571] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1154.777766] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1186.493044] ata1.00: limiting speed to UDMA/66:PIO4
[ 1186.493050] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1186.493113] ata1.00: cmd ca/00:10:17:25:f6/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 1186.493115] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1186.493177] ata1.00: status: { DRDY }
[ 1186.493228] ata1: hard resetting link
[ 1187.155167] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1187.156365] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1187.158855] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1187.159972] ata1.00: configured for UDMA/66
[ 1187.159972] ata1: EH complete
[ 1187.161154] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1187.161283] sd 0:0:0:0: [sda] Write Protect is off
[ 1187.161286] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1187.161567] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1217.172036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1217.172098] ata1.00: cmd 35/00:00:47:01:f8/00:04:02:00:00/e0 tag 0 dma 524288 out
[ 1217.172100] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1217.172162] ata1.00: status: { DRDY }
[ 1217.172212] ata1: hard resetting link
[ 1217.936036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1217.937237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1217.940440] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1217.941572] ata1.00: configured for UDMA/66
[ 1217.941572] ata1: EH complete
[ 1217.949939] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1217.954021] sd 0:0:0:0: [sda] Write Protect is off
[ 1217.954021] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1217.961634] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1315.895050] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1315.895088] ata1.00: cmd ca/00:20:d7:23:f8/00:00:00:00:00/e2 tag 0 dma 16384 out
[ 1315.895090] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1315.895119] ata1.00: status: { DRDY }
[ 1315.895138] ata1: hard resetting link
[ 1316.557036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1316.558237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1316.561473] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1316.562606] ata1.00: configured for UDMA/66
[ 1316.562606] ata1: EH complete
[ 1316.562820] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1316.562820] sd 0:0:0:0: [sda] Write Protect is off
[ 1316.562820] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1316.562820] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1346.570036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1346.570064] ata1.00: cmd ca/00:08:57:0a:49/00:00:00:00:00/e0 tag 0 dma 4096 out
[ 1346.570065] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1346.570095] ata1.00: status: { DRDY }
[ 1346.570112] ata1: hard resetting link
[ 1347.334036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1347.335237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1347.338409] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1347.339542] ata1.00: configured for UDMA/66
[ 1347.339542] ata1: EH complete
[ 1347.339715] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1347.339793] sd 0:0:0:0: [sda] Write Protect is off
[ 1347.339793] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1347.339976] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1377.351032] ata1.00: limiting speed to UDMA/33:PIO4
[ 1377.351036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1377.351063] ata1.00: cmd ca/00:08:cf:09:cd/00:00:00:00:00/e0 tag 0 dma 4096 out
[ 1377.351064] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1377.351093] ata1.00: status: { DRDY }
[ 1377.351111] ata1: hard resetting link
[ 1378.166173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1378.167377] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1378.170232] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1378.171349] ata1.00: configured for UDMA/33
[ 1378.171349] ata1: EH complete
[ 1378.171518] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1378.171593] sd 0:0:0:0: [sda] Write Protect is off
[ 1378.171593] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1378.171656] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1408.178032] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1408.178060] ata1.00: cmd ca/00:10:c7:94:f1/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 1408.178061] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1408.178090] ata1.00: status: { DRDY }
[ 1408.178108] ata1: hard resetting link
[ 1408.993173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1408.994375] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1408.996870] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1408.997988] ata1.00: configured for UDMA/33
[ 1408.997988] ata1: EH complete
[ 1408.998203] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1408.998340] sd 0:0:0:0: [sda] Write Protect is off
[ 1408.998340] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1408.998523] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1439.006036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1439.006066] ata1.00: cmd ca/00:10:27:13:91/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 1439.006067] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1439.006097] ata1.00: status: { DRDY }
[ 1439.006116] ata1: hard resetting link
[ 1439.821174] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1439.822375] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1439.824872] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1439.825988] ata1.00: configured for UDMA/33
[ 1439.825988] ata1: EH complete
[ 1439.826156] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1439.826252] sd 0:0:0:0: [sda] Write Protect is off
[ 1439.826252] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1439.826488] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1469.836037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1469.836065] ata1.00: cmd ca/00:08:7f:4e:f8/00:00:00:00:00/e2 tag 0 dma 4096 out
[ 1469.836067] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1469.836096] ata1.00: status: { DRDY }
[ 1469.836114] ata1: hard resetting link
[ 1470.651175] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1470.652376] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1470.654877] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1470.655994] ata1.00: configured for UDMA/33
[ 1470.655994] ata1: EH complete
[ 1470.656164] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1470.656240] sd 0:0:0:0: [sda] Write Protect is off
[ 1470.656240] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1470.656398] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1500.664044] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1500.664071] ata1.00: cmd ca/00:10:2f:72:f8/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 1500.664072] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1500.664101] ata1.00: status: { DRDY }
[ 1500.664119] ata1: hard resetting link
[ 1501.428036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1501.429237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1501.432423] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1501.433555] ata1.00: configured for UDMA/33
[ 1501.433555] ata1: EH complete
[ 1501.433855] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1501.433951] sd 0:0:0:0: [sda] Write Protect is off
[ 1501.433951] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1501.434106] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1531.443037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1531.443064] ata1.00: cmd ca/00:08:e7:91:f8/00:00:00:00:00/e2 tag 0 dma 4096 out
[ 1531.443066] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1531.443095] ata1.00: status: { DRDY }
[ 1531.443112] ata1: hard resetting link
[ 1532.207034] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1532.208235] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1532.211421] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1532.212554] ata1.00: configured for UDMA/33
[ 1532.212554] ata1: EH complete
[ 1532.212758] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1532.212867] sd 0:0:0:0: [sda] Write Protect is off
[ 1532.212867] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1532.213025] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1562.219036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1562.219064] ata1.00: cmd ca/00:08:2f:ac:f8/00:00:00:00:00/e2 tag 0 dma 4096 out
[ 1562.219066] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1562.219095] ata1.00: status: { DRDY }
[ 1562.219113] ata1: hard resetting link
[ 1562.983062] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1562.984249] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1562.987424] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1562.988556] ata1.00: configured for UDMA/33
[ 1562.988556] ata1: EH complete
[ 1562.988748] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1562.988851] sd 0:0:0:0: [sda] Write Protect is off
[ 1562.988851] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1562.989049] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1592.996034] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1592.996062] ata1.00: cmd ca/00:10:5f:c9:f8/00:00:00:00:00/e2 tag 0 dma 8192 out
[ 1592.996063] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1592.996093] ata1.00: status: { DRDY }
[ 1592.996110] ata1: hard resetting link
[ 1593.760172] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1593.761372] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1593.763862] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 1593.764977] ata1.00: configured for UDMA/33
[ 1593.764977] ata1: EH complete
[ 1593.765183] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 1593.765206] sd 0:0:0:0: [sda] Write Protect is off
[ 1593.765206] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1593.765206] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1617.738192] usb 2-5: new high speed USB device using ehci_hcd and address 4
[ 1617.852903] usb 2-5: configuration #1 chosen from 1 choice
[ 1617.859032] scsi7 : SCSI emulation for USB Mass Storage devices
[ 1617.862832] usb-storage: device found at 4
[ 1617.862834] usb-storage: waiting for device to settle before scanning
[ 1622.862353] usb-storage: device scan complete
[ 1622.862703] scsi 7:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2
[ 1622.864004] sd 7:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB)
[ 1622.864615] sd 7:0:0:0: [sdb] Write Protect is off
[ 1622.864618] sd 7:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 1622.864621] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 1622.866735] sd 7:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB)
[ 1622.867362] sd 7:0:0:0: [sdb] Write Protect is off
[ 1622.867365] sd 7:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 1622.867367] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 1622.867420] sdb: sdb1
[ 1622.868538] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 1622.868580] sd 7:0:0:0: Attached scsi generic sg2 type 0
