Add documentation for the updated ACPI specs for EINJv2(1)(2) (1)https://bugzilla.tianocore.org/show_bug.cgi?id=4615 (2)https://bugzilla.tianocore.org/attachment.cgi?id=1446 Signed-off-by: Zaid Alali <zaidal@xxxxxxxxxxxxxxxxxxxxxx> --- .../firmware-guide/acpi/apei/einj.rst | 46 ++++++++++++++++++- 1 file changed, 44 insertions(+), 2 deletions(-) diff --git a/Documentation/firmware-guide/acpi/apei/einj.rst b/Documentation/firmware-guide/acpi/apei/einj.rst index c52b9da08fa9..3ad092111035 100644 --- a/Documentation/firmware-guide/acpi/apei/einj.rst +++ b/Documentation/firmware-guide/acpi/apei/einj.rst @@ -61,6 +61,14 @@ The following files belong to it: 0x00000800 Platform Uncorrectable fatal ================ =================================== + ================ =================================== + Error Type Value Error Description + ================ =================================== + 0x00000001 EINJV2 Processor Error + 0x00000002 EINJV2 Memory Error + 0x00000004 EINJV2 PCI Express Error + ================ =================================== + The format of the file contents are as above, except present are only the available error types. @@ -85,9 +93,11 @@ The following files belong to it: Bit 0 Processor APIC field valid (see param3 below). Bit 1 - Memory address and mask valid (param1 and param2). + Memory address and range valid (param1 and param2). Bit 2 PCIe (seg,bus,dev,fn) valid (see param4 below). + Bit 3 + EINJv2 extension structure is valid If set to zero, legacy behavior is mimicked where the type of injection specifies just one bit set, and param1 is multiplexed. @@ -110,6 +120,7 @@ The following files belong to it: Used when the 0x1 bit is set in "flags" to specify the APIC id - param4 + Used when the 0x4 bit is set in "flags" to specify target PCIe device - notrigger @@ -122,6 +133,18 @@ The following files belong to it: this actually works depends on what operations the BIOS actually includes in the trigger phase. +- einjv2_component_count + + The value from this file is used to set the "Component Array Count" + field of EINJv2 Extension Structure. + +- einjv2_component_array + + The contents of this file are used to set the "Component Array" field + of the EINJv2 Extension Structure. The expected format is hex values + for component id and syndrome separated by space, and multiple + components are separated by new line. + CXL error types are supported from ACPI 6.5 onwards (given a CXL port is present). The EINJ user interface for CXL error types is at <debugfs mount point>/cxl. The following files belong to it: @@ -139,7 +162,6 @@ is present). The EINJ user interface for CXL error types is at under <debugfs mount point>/apei/einj, while CXL 1.1/1.0 port injections must use this file. - BIOS versions based on the ACPI 4.0 specification have limited options in controlling where the errors are injected. Your BIOS may support an extension (enabled with the param_extension=1 module parameter, or boot @@ -194,6 +216,26 @@ An error injection example:: # echo 0x8 > error_type # Choose correctable memory error # echo 1 > error_inject # Inject now +An EINJv2 error injection example:: + + # cd /sys/kernel/debug/apei/einj + # cat available_error_type # See which errors can be injected + 0x00000002 Processor Uncorrectable non-fatal + 0x00000008 Memory Correctable + 0x00000010 Memory Uncorrectable non-fatal + 0x00000001 EINJV2 Processor Error + 0x00000002 EINJV2 Memory Error + + # echo 0x12345000 > param1 # Set memory address for injection + # echo 0xfffffffffffff000 > param2 # Range - anywhere in this page + # comp_arr="0x1 0x2 # Fill in the component array + >0x1 0x4 + >0x2 0x4" + # echo "$comp_arr" > einjv2_component_array + # echo 0x2 > error_type # Choose EINJv2 memory error + # echo 0xa > flags # set flags to indicate EINJv2 + # echo 1 > error_inject # Inject now + You should see something like this in dmesg:: [22715.830801] EDAC sbridge MC3: HANDLING MCE MEMORY ERROR -- 2.34.1