Re: [PATCH v5 4/4] PCI: Allow PCI bridges to go to D3Hot on all Devicetree based platforms

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Aug 6, 2024 at 7:39 AM Manivannan Sadhasivam
<manivannan.sadhasivam@xxxxxxxxxx> wrote:
>
> On Tue, Aug 06, 2024 at 03:02:39PM +0200, Lukas Wunner wrote:
> > On Tue, Aug 06, 2024 at 06:11:07PM +0530, Manivannan Sadhasivam wrote:
> > > On Tue, Aug 06, 2024 at 08:53:01AM +0200, Lukas Wunner wrote:
> > > > AFAICS we always program the device to go to D3hot and the platform
> > > > then cuts power, thereby putting it into D3cold.  So D3hot is never
> > > > skipped.  See __pci_set_power_state():
> > > >
> > > >   if (state == PCI_D3cold) {
> > > >           /*
> > > >            * To put the device in D3cold, put it into D3hot in the native
> > > >            * way, then put it into D3cold using platform ops.
> > > >            */
> > > >           error = pci_set_low_power_state(dev, PCI_D3hot, locked);
> > > >
> > > >           if (pci_platform_power_transition(dev, PCI_D3cold))
> > > >                   return error;
> > > >
> > >
> > > This is applicable only to pci_set_power_state(), but AFAIK PCIe spec
> > > doesn't mandate switching to D3Hot for entering D3Cold.
> >
> > Per PCI Bus Power Management Interface Specification r1.2 sec 5.5 fig 5-1,
> > the only supported state transition to D3cold is from D3hot.
> >
> > Per PCIe r6.2 sec 5.2, "PM is compatible with the PCI Bus Power Management
> > Interface Specification".
> >
> > Granted, PCI-PM is an ancient spec, so I think anyone can be forgiven
> > for not knowing its intricacies off-the-cuff. :)
> >
>
> Ah, the grand old PCI-PM... I don't remember the last time I looked into it :)
>
> >
> > > So the PCIe host controller drivers (especically non-ACPI platforms)
> > > may just send PME_Turn_Off followed by removing the slot power
> > > (which again is not controlled by pci_set_power_state())
> > > as there are no non-ACPI related hooks as of now.
> >
> > Ideally, devicetree-based platforms should be brought into the
> > platform_pci_*() fold to align them with ACPI and get common
> > behavior across all platforms.
> >
>
> Yeah, that would be the ideal case. Unfortunately, there is no ideal ground for
> DT :/ We do not even have the supplies populated properly. But with the advent
> of power sequencing framework, I think this can be fixed.
>

Looking in acpi_pci_bridge_d3(), it has several checkings about
whether d3 is supported, including reading power_manageable flag
(acpi_device_power_manageable) and reading the root port property.
For DT, does it make sense to have a chosen property about this?

> Regarding your comment on patch 3/4, we already have the sysfs attribute to
> control whether the device can be put into D3Cold or not and that is directly
> coming from userspace. So there is no guarantee to assume that D3Hot support is
> considered.
>
> - Mani
>
> --
> மணிவண்ணன் சதாசிவம்





[Index of Archives]     [Linux IBM ACPI]     [Linux Power Management]     [Linux Kernel]     [Linux Laptop]     [Kernel Newbies]     [Share Photos]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]
  Powered by Linux