On Sun, 11 Dec 2022 23:06:21 -0800
ira.weiny@xxxxxxxxx wrote:
> From: Davidlohr Bueso <dave@xxxxxxxxxxxx>
>
> Currently the only CXL features targeted for irq support require their
> message numbers to be within the first 16 entries. The device may
> however support less than 16 entries depending on the support it
> provides.
>
> Attempt to allocate these 16 irq vectors. If the device supports less
> then the PCI infrastructure will allocate that number. Upon successful
> allocation, users can plug in their respective isr at any point
> thereafter.
>
> CXL device events are signaled via interrupts. Each event log may have
> a different interrupt message number. These message numbers are
> reported in the Get Event Interrupt Policy mailbox command.
>
> Add interrupt support for event logs. Interrupts are allocated as
> shared interrupts. Therefore, all or some event logs can share the same
> message number.
>
> In addition all logs are queried on any interrupt in order of the most
> to least severe based on the status register.
>
> Cc: Bjorn Helgaas <helgaas@xxxxxxxxxx>
> Cc: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
> Co-developed-by: Ira Weiny <ira.weiny@xxxxxxxxx>
> Signed-off-by: Ira Weiny <ira.weiny@xxxxxxxxx>
> Signed-off-by: Davidlohr Bueso <dave@xxxxxxxxxxxx>
Sometimes it feels like we go around in circles as I'm sure we've
fixed this at least 3 times now in different sets that got dropped
(was definitely in the DOE interrupt support set and was controversial ;)
Nothing in this patch set calls pci_set_master() so no interrupts
will even be delivered. I don't think there are any sets in flight
that would fix that.
Jonathan
>
> ---
> Changes from V3:
> Adjust based on changes in patch 1
> Consolidate event setup into cxl_event_config()
> Consistently use cxl_event_* for function names
> Remove cxl_event_int_is_msi()
> Ensure DCD log is ignored in status
> Simplify event status loop logic
> Dan
> Fail driver load if the irq's are not allocated
> move cxl_event_config_msgnums() to pci.c
> s/CXL_PCI_REQUIRED_VECTORS/CXL_PCI_DEFAULT_MAX_VECTORS
> s/devm_kmalloc/devm_kzalloc
> Fix up pci_alloc_irq_vectors() comment
> Pass pdev to cxl_alloc_irq_vectors()
> Check FW irq policy prior to configuration
> Jonathan
> Use FIELD_GET instead of manual masking
> ---
> drivers/cxl/cxl.h | 4 +
> drivers/cxl/cxlmem.h | 19 ++++
> drivers/cxl/cxlpci.h | 6 ++
> drivers/cxl/pci.c | 208 +++++++++++++++++++++++++++++++++++++++++--
> 4 files changed, 231 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/cxl/cxl.h b/drivers/cxl/cxl.h
> index 5974d1082210..b3964149c77b 100644
> --- a/drivers/cxl/cxl.h
> +++ b/drivers/cxl/cxl.h
> @@ -168,6 +168,10 @@ static inline int ways_to_eiw(unsigned int ways, u8 *eiw)
> CXLDEV_EVENT_STATUS_FAIL | \
> CXLDEV_EVENT_STATUS_FATAL)
>
> +/* CXL rev 3.0 section 8.2.9.2.4; Table 8-52 */
> +#define CXLDEV_EVENT_INT_MODE_MASK GENMASK(1, 0)
> +#define CXLDEV_EVENT_INT_MSGNUM_MASK GENMASK(7, 4)
> +
> /* CXL 2.0 8.2.8.4 Mailbox Registers */
> #define CXLDEV_MBOX_CAPS_OFFSET 0x00
> #define CXLDEV_MBOX_CAP_PAYLOAD_SIZE_MASK GENMASK(4, 0)
> diff --git a/drivers/cxl/cxlmem.h b/drivers/cxl/cxlmem.h
> index dd9aa3dd738e..bd8bfbe61ec8 100644
> --- a/drivers/cxl/cxlmem.h
> +++ b/drivers/cxl/cxlmem.h
> @@ -194,6 +194,23 @@ struct cxl_endpoint_dvsec_info {
> struct range dvsec_range[2];
> };
>
> +/**
> + * Event Interrupt Policy
> + *
> + * CXL rev 3.0 section 8.2.9.2.4; Table 8-52
> + */
> +enum cxl_event_int_mode {
> + CXL_INT_NONE = 0x00,
> + CXL_INT_MSI_MSIX = 0x01,
> + CXL_INT_FW = 0x02
> +};
> +struct cxl_event_interrupt_policy {
> + u8 info_settings;
> + u8 warn_settings;
> + u8 failure_settings;
> + u8 fatal_settings;
> +} __packed;
> +
> /**
> * struct cxl_event_state - Event log driver state
> *
> @@ -288,6 +305,8 @@ enum cxl_opcode {
> CXL_MBOX_OP_RAW = CXL_MBOX_OP_INVALID,
> CXL_MBOX_OP_GET_EVENT_RECORD = 0x0100,
> CXL_MBOX_OP_CLEAR_EVENT_RECORD = 0x0101,
> + CXL_MBOX_OP_GET_EVT_INT_POLICY = 0x0102,
> + CXL_MBOX_OP_SET_EVT_INT_POLICY = 0x0103,
> CXL_MBOX_OP_GET_FW_INFO = 0x0200,
> CXL_MBOX_OP_ACTIVATE_FW = 0x0202,
> CXL_MBOX_OP_GET_SUPPORTED_LOGS = 0x0400,
> diff --git a/drivers/cxl/cxlpci.h b/drivers/cxl/cxlpci.h
> index 77dbdb980b12..a8ea04f536ab 100644
> --- a/drivers/cxl/cxlpci.h
> +++ b/drivers/cxl/cxlpci.h
> @@ -53,6 +53,12 @@
> #define CXL_DVSEC_REG_LOCATOR_BLOCK_ID_MASK GENMASK(15, 8)
> #define CXL_DVSEC_REG_LOCATOR_BLOCK_OFF_LOW_MASK GENMASK(31, 16)
>
> +/*
> + * NOTE: Currently all the functions which are enabled for CXL require their
> + * vectors to be in the first 16. Use this as the default max.
> + */
> +#define CXL_PCI_DEFAULT_MAX_VECTORS 16
> +
> /* Register Block Identifier (RBI) */
> enum cxl_regloc_type {
> CXL_REGLOC_RBI_EMPTY = 0,
> diff --git a/drivers/cxl/pci.c b/drivers/cxl/pci.c
> index a2d8382bc593..d42d87faddb8 100644
> --- a/drivers/cxl/pci.c
> +++ b/drivers/cxl/pci.c
> @@ -445,6 +445,201 @@ static int cxl_mem_alloc_event_buf(struct cxl_dev_state *cxlds)
> return 0;
> }
>
> +static int cxl_alloc_irq_vectors(struct pci_dev *pdev)
> +{
> + int nvecs;
> +
> + /*
> + * CXL requires MSI/MSIX support.
> + *
> + * Additionally pci_alloc_irq_vectors() handles calling
> + * pci_free_irq_vectors() automatically despite not being called
> + * pcim_*. See pci_setup_msi_context().
> + */
> + nvecs = pci_alloc_irq_vectors(pdev, 1, CXL_PCI_DEFAULT_MAX_VECTORS,
> + PCI_IRQ_MSIX | PCI_IRQ_MSI);
> + if (nvecs < 1) {
> + dev_dbg(&pdev->dev, "Failed to alloc irq vectors: %d\n", nvecs);
> + return -ENXIO;
> + }
> + return 0;
> +}
> +
> +struct cxl_dev_id {
> + struct cxl_dev_state *cxlds;
> +};
> +
> +static irqreturn_t cxl_event_thread(int irq, void *id)
> +{
> + struct cxl_dev_id *dev_id = id;
> + struct cxl_dev_state *cxlds = dev_id->cxlds;
> + u32 status;
> +
> + do {
> + /*
> + * CXL 3.0 8.2.8.3.1: The lower 32 bits are the status;
> + * ignore the reserved upper 32 bits
> + */
> + status = readl(cxlds->regs.status + CXLDEV_DEV_EVENT_STATUS_OFFSET);
> + /* Ignore logs unknown to the driver */
> + status &= CXLDEV_EVENT_STATUS_ALL;
> + if (!status)
> + break;
> + cxl_mem_get_event_records(cxlds, status);
> + cond_resched();
> + } while (status);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int cxl_event_req_irq(struct cxl_dev_state *cxlds, u8 setting)
> +{
> + struct device *dev = cxlds->dev;
> + struct pci_dev *pdev = to_pci_dev(dev);
> + struct cxl_dev_id *dev_id;
> + int irq;
> +
> + if (FIELD_GET(CXLDEV_EVENT_INT_MODE_MASK, setting) != CXL_INT_MSI_MSIX)
> + return -ENXIO;
> +
> + /* dev_id must be globally unique and must contain the cxlds */
> + dev_id = devm_kzalloc(dev, sizeof(*dev_id), GFP_KERNEL);
> + if (!dev_id)
> + return -ENOMEM;
> + dev_id->cxlds = cxlds;
> +
> + irq = pci_irq_vector(pdev,
> + FIELD_GET(CXLDEV_EVENT_INT_MSGNUM_MASK, setting));
> + if (irq < 0)
> + return irq;
> +
> + return devm_request_threaded_irq(dev, irq, NULL, cxl_event_thread,
> + IRQF_SHARED, NULL, dev_id);
> +}
> +
> +static int cxl_event_get_int_policy(struct cxl_dev_state *cxlds,
> + struct cxl_event_interrupt_policy *policy)
> +{
> + struct cxl_mbox_cmd mbox_cmd = (struct cxl_mbox_cmd) {
> + .opcode = CXL_MBOX_OP_GET_EVT_INT_POLICY,
> + .payload_out = policy,
> + .size_out = sizeof(*policy),
> + };
> + int rc;
> +
> + rc = cxl_internal_send_cmd(cxlds, &mbox_cmd);
> + if (rc < 0)
> + dev_err(cxlds->dev, "Failed to get event interrupt policy : %d",
> + rc);
> +
> + return rc;
> +}
> +
> +static int cxl_event_config_msgnums(struct cxl_dev_state *cxlds,
> + struct cxl_event_interrupt_policy *policy)
> +{
> + struct cxl_mbox_cmd mbox_cmd;
> + int rc;
> +
> + policy->info_settings = CXL_INT_MSI_MSIX;
> + policy->warn_settings = CXL_INT_MSI_MSIX;
> + policy->failure_settings = CXL_INT_MSI_MSIX;
> + policy->fatal_settings = CXL_INT_MSI_MSIX;
> +
> + mbox_cmd = (struct cxl_mbox_cmd) {
> + .opcode = CXL_MBOX_OP_SET_EVT_INT_POLICY,
> + .payload_in = policy,
> + .size_in = sizeof(*policy),
> + };
> +
> + rc = cxl_internal_send_cmd(cxlds, &mbox_cmd);
> + if (rc < 0) {
> + dev_err(cxlds->dev, "Failed to set event interrupt policy : %d",
> + rc);
> + return rc;
> + }
> +
> + /* Retrieve final interrupt settings */
> + return cxl_event_get_int_policy(cxlds, policy);
> +}
> +
> +static int cxl_event_irqsetup(struct cxl_dev_state *cxlds)
> +{
> + struct cxl_event_interrupt_policy policy;
> + int rc;
> +
> + rc = cxl_event_config_msgnums(cxlds, &policy);
> + if (rc)
> + return rc;
> +
> + rc = cxl_event_req_irq(cxlds, policy.info_settings);
> + if (rc) {
> + dev_err(cxlds->dev, "Failed to get interrupt for event Info log\n");
> + return rc;
> + }
> +
> + rc = cxl_event_req_irq(cxlds, policy.warn_settings);
> + if (rc) {
> + dev_err(cxlds->dev, "Failed to get interrupt for event Warn log\n");
> + return rc;
> + }
> +
> + rc = cxl_event_req_irq(cxlds, policy.failure_settings);
> + if (rc) {
> + dev_err(cxlds->dev, "Failed to get interrupt for event Failure log\n");
> + return rc;
> + }
> +
> + rc = cxl_event_req_irq(cxlds, policy.fatal_settings);
> + if (rc) {
> + dev_err(cxlds->dev, "Failed to get interrupt for event Fatal log\n");
> + return rc;
> + }
> +
> + return 0;
> +}
> +
> +static bool cxl_event_int_is_fw(u8 setting)
> +{
> + u8 mode = FIELD_GET(CXLDEV_EVENT_INT_MODE_MASK, setting);
> +
> + return mode == CXL_INT_FW;
> +}
> +
> +static int cxl_event_config(struct pci_host_bridge *host_bridge,
> + struct cxl_dev_state *cxlds)
> +{
> + struct cxl_event_interrupt_policy policy;
> + int rc;
> +
> + /*
> + * When BIOS maintains CXL error reporting control, it will process
> + * event records. Only one agent can do so.
> + */
> + if (!host_bridge->native_cxl_error)
> + return 0;
> +
> + rc = cxl_event_get_int_policy(cxlds, &policy);
> + if (rc)
> + return rc;
> +
> + if (cxl_event_int_is_fw(policy.info_settings) ||
> + cxl_event_int_is_fw(policy.warn_settings) ||
> + cxl_event_int_is_fw(policy.failure_settings) ||
> + cxl_event_int_is_fw(policy.fatal_settings)) {
> + dev_err(cxlds->dev, "FW still in control of Event Logs despite _OSC settings\n");
> + return -EBUSY;
> + }
> +
> + rc = cxl_event_irqsetup(cxlds);
> + if (rc)
> + return rc;
> +
> + cxl_mem_get_event_records(cxlds, CXLDEV_EVENT_STATUS_ALL);
> +
> + return 0;
> +}
> +
> static int cxl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
> {
> struct pci_host_bridge *host_bridge = pci_find_host_bridge(pdev->bus);
> @@ -519,6 +714,10 @@ static int cxl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
> if (rc)
> return rc;
>
> + rc = cxl_alloc_irq_vectors(pdev);
> + if (rc)
> + return rc;
> +
> cxlmd = devm_cxl_add_memdev(cxlds);
> if (IS_ERR(cxlmd))
> return PTR_ERR(cxlmd);
> @@ -527,12 +726,9 @@ static int cxl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
> if (rc)
> return rc;
>
> - /*
> - * When BIOS maintains CXL error reporting control, it will process
> - * event records. Only one agent can do so.
> - */
> - if (host_bridge->native_cxl_error)
> - cxl_mem_get_event_records(cxlds, CXLDEV_EVENT_STATUS_ALL);
> + rc = cxl_event_config(host_bridge, cxlds);
> + if (rc)
> + return rc;
>
> if (cxlds->regs.ras) {
> pci_enable_pcie_error_reporting(pdev);
