On Tue, Jul 27, 2021 at 12:56 PM Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx> wrote: > > Hi Rafael, > > On Mon, Jul 12, 2021 at 07:06:47PM +0200, Rafael J. Wysocki wrote: > > From: Rafael J. Wysocki <rafael.j.wysocki@xxxxxxxxx> > > > > Some PCIe devices only support PME (Power Management Event) from > > D3cold. One example is the ASMedia xHCI controller: > > > > 11:00.0 USB controller: ASMedia Technology Inc. ASM1042A USB 3.0 Host Controller (prog-if 30 [XHCI]) > > ... > > Capabilities: [78] Power Management version 3 > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0-,D1-,D2-,D3hot-,D3cold+) > > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > > > > In those cases, if the device is expected to generate wakeup events > > from its final power state, pci_target_state() returns D0, which > > prevents the PCIe port the device is connected to from entering any > > low-power states too. However, if the device were allowed to go into > > D3hot, its parent PCIe port would also be able to go into D3 and if > > it goes into D3cold, it would cause the endpoint device to end up in > > D3cold too (as per the PCI PM spec v1.2, Table 6-1), in which case > > the endpoint would be able to signal PME. This means that the system > > could be put into a lower-power configuration without sacrificing the > > the given device's ability to generate PME. > > > > In order to avoid missing that opportunity, extend pci_pme_capable() > > to check the device's parent in the special case when the target > > state is D3hot and the device can only signal PME from D3cold and > > update pci_target_state() to return the current target state if > > pci_pme_capable() returns 'true' for it. > > Thanks a lot for this! > > I tried the patch and unfortunately it does not solve the issue but I > think I know what the problem is, see below. OK, it's good that you can access a system having this issue. > > Link: https://lore.kernel.org/linux-pm/20210617123653.58640-1-mika.westerberg@xxxxxxxxxxxxxxx > > Reported-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx> > > Reported-by: Utkarsh H Patel <utkarsh.h.patel@xxxxxxxxx> > > Reported-by: Koba Ko <koba.ko@xxxxxxxxxxxxx> > > Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@xxxxxxxxx> > > --- > > > > Hi, > > > > Anyone who can reproduce the problem described in the changelog, > > please test the patch and let me know the result. > > > > Thanks! > > > > --- > > drivers/pci/pci.c | 38 ++++++++++++++++++++++++++------------ > > 1 file changed, 26 insertions(+), 12 deletions(-) > > > > Index: linux-pm/drivers/pci/pci.c > > =================================================================== > > --- linux-pm.orig/drivers/pci/pci.c > > +++ linux-pm/drivers/pci/pci.c > > @@ -2298,10 +2298,29 @@ void pci_pme_wakeup_bus(struct pci_bus * > > */ > > bool pci_pme_capable(struct pci_dev *dev, pci_power_t state) > > { > > + struct pci_dev *parent; > > + > > if (!dev->pm_cap) > > return false; > > > > - return !!(dev->pme_support & (1 << state)); > > + if (dev->pme_support & (1 << state)) > > + return true; > > + > > + /* > > + * Special case: The target state is D3hot and the device only supports > > + * signaling PME from D3cold, but it is a PCIe device whose parent port > > + * can go into D3cold. In that case, if the device is allowed to go > > + * into D3hot, the parent port can go into D3cold which will cause the > > + * device to end up in D3cold, so it will be able to signal PME from the > > + * final state. > > + */ > > + if (state != PCI_D3hot || !(dev->pme_support & (1 << PCI_D3cold))) > > + return false; > > + > > + parent = dev->bus->self; > > + return pci_bridge_d3_possible(parent) && > > + platform_pci_power_manageable(parent) && > > Here. We cannot assume that the parent has ACPI node either. I see. Obviously, I assumed that this was the case. > For instance when PCIe is tunneled over TBT/USB4 there can be several PCIe > switches between the problem endpoint and the root port (which has the > ACPI node of course). I think the safe assumption is to check for the > root port and whether platform_pci_power_manageable() returns true for > it but I may be missing something. Well, if any of the ports on the path between the target endpoint and the root complex can be put into D3cold via ACPI, the endpoint will end up in D3cold effectively, so I think that all of them need to be checked. Let me change the patch to do that. > > + platform_pci_choose_state(parent) == PCI_D3cold; > > } > > EXPORT_SYMBOL(pci_pme_capable); > > > > @@ -2595,17 +2614,12 @@ static pci_power_t pci_target_state(stru > > if (dev->current_state == PCI_D3cold) > > target_state = PCI_D3cold; > > > > - if (wakeup) { > > - /* > > - * Find the deepest state from which the device can generate > > - * PME#. > > - */ > > - if (dev->pme_support) { > > - while (target_state > > - && !(dev->pme_support & (1 << target_state))) > > - target_state--; > > - } > > - } > > + if (!wakeup || !dev->pme_support || pci_pme_capable(dev, target_state)) > > + return target_state; > > + > > + /* Find the deepest state from which the device can generate PME#. */ > > + while (target_state && !(dev->pme_support & (1 << target_state))) > > + target_state--; > > > > return target_state; > > } > > > >
