On Thu, 2007-11-15 at 11:38 +0100, Frank Munsche wrote: > Hello, > > I've got a Sony Vaio SZ61 running gentoo, 2.6.22-gentoo-r9 . Although there is > acpi - information available in /proc/acpi (e.g. battery, ac_adapter, > processor) I never get apci - events reported. > If I pull the ac - cable, it is recognized and the processors freq. gets > modified by cpufreqd. But there seems no (visible) acpi event generated. > That's weird. Please open an ACPI bug in http://bugzilla.kernel.org/enter_bug.cgi Please attach the acpidump, and dmesg output there. please do the following test, #dmesg -c #echo 0x04 > /sys/module/acpi/parameters/debug_layer #echo 0x8800001f > /sys/module/acpi/parameters/debug_level plug/unuplug the ac cable and attach the dmesg output after this test. > > I' ve tried the current 2.6.23.1, but got the same result. > Just as other things (like the powerbutton), which should generate an event, > but don't. > That's really strange. For 2.6.23.1, please make sure ACPI_PROC_EVENTS is set. Thanks, Rui > > Linux version 2.6.23.1 (root@da) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #1 > SMP Mon Nov 12 13:16:57 CET 2007 > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved) > BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000007f6b0000 (usable) > BIOS-e820: 000000007f6b0000 - 000000007f6cb000 (ACPI NVS) > BIOS-e820: 000000007f6cb000 - 0000000080000000 (reserved) > BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) > BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) > BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved) > BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) > BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) > 1142MB HIGHMEM available. > 896MB LOWMEM available. > found SMP MP-table at 000f7710 > Entering add_active_range(0, 0, 521904) 0 entries of 256 used > Zone PFN ranges: > DMA 0 -> 4096 > Normal 4096 -> 229376 > HighMem 229376 -> 521904 > Movable zone start PFN for each node > early_node_map[1] active PFN ranges > 0: 0 -> 521904 > On node 0 totalpages: 521904 > DMA zone: 32 pages used for memmap > DMA zone: 0 pages reserved > DMA zone: 4064 pages, LIFO batch:0 > Normal zone: 1760 pages used for memmap > Normal zone: 223520 pages, LIFO batch:31 > HighMem zone: 2285 pages used for memmap > HighMem zone: 290243 pages, LIFO batch:31 > Movable zone: 0 pages used for memmap > DMI present. > ACPI: RSDP 000F76E0, 0024 (r2 PTLTD ) > ACPI: XSDT 7F6BE790, 009C (r1 Sony VAIO 20070712 PTL 0) > ACPI: FACP 7F6C7BD2, 00F4 (r3 Sony VAIO 20070712 PTL 1) > ACPI: DSDT 7F6C07F3, 736B (r2 Sony VAIO 20070712 PTL 20050624) > ACPI: FACS 7F6CAFC0, 0040 > ACPI: APIC 7F6C7CC6, 0068 (r1 Sony VAIO 20070712 PTL 5A) > ACPI: HPET 7F6C7D2E, 0038 (r1 Sony VAIO 20070712 PTL 5A) > ACPI: MCFG 7F6C7D66, 003C (r1 Sony VAIO 20070712 PTL 5A) > ACPI: TCPA 7F6C7DA2, 0032 (r1 Sony VAIO 20070712 PTL 5A52) > ACPI: TMOR 7F6C7DD4, 0026 (r1 Sony VAIO 20070712 PTL 3) > ACPI: SLIC 7F6C7DFA, 0176 (r1 Sony VAIO 20070712 PTL 1000000) > ACPI: APIC 7F6C7F70, 0068 (r1 Sony VAIO 20070712 PTL 0) > ACPI: BOOT 7F6C7FD8, 0028 (r1 Sony VAIO 20070712 PTL 1) > ACPI: SSDT 7F6C0132, 06C1 (r1 Sony VAIO 20070712 PTL 20050624) > ACPI: SSDT 7F6BFA24, 070E (r1 Sony VAIO 20070712 PTL 20050624) > ACPI: SSDT 7F6BF902, 0122 (r1 Sony VAIO 20070712 PTL 20050624) > ACPI: SSDT 7F6BEDB8, 025F (r1 Sony VAIO 20070712 PTL 20050624) > ACPI: SSDT 7F6BED12, 00A6 (r1 Sony VAIO 20070712 PTL 20050624) > ACPI: SSDT 7F6BE82C, 04E6 (r1 Sony VAIO 20070712 PTL 20050624) > ACPI: BIOS bug: multiple APIC/MADT found, using 0 > ACPI: If "acpi_apic_instance=2" works better, notify > linux-acpi@xxxxxxxxxxxxxxx > ACPI: PM-Timer IO Port: 0x1008 > ACPI: Local APIC address 0xfee00000 > ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > Processor #0 6:15 APIC version 20 > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) > Processor #1 6:15 APIC version 20 > ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) > ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) > ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) > IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > ACPI: IRQ0 used by override. > ACPI: IRQ2 used by override. > ACPI: IRQ9 used by override. > Enabling APIC mode: Flat. Using 1 I/O APICs > ACPI: HPET id: 0x8086a201 base: 0xfed00000 > Using ACPI (MADT) for SMP configuration information > Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) > swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 > swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000 > swsusp: Registered nosave memory region: 00000000000d2000 - 00000000000d4000 > swsusp: Registered nosave memory region: 00000000000d4000 - 00000000000e0000 > swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000 > Built 1 zonelists in Zone order. Total pages: 517827 > Kernel command line: root=/dev/sda6 > mapped APIC to ffffb000 (fee00000) > mapped IOAPIC to ffffa000 (fec00000) > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Initializing CPU#0 > PID hash table entries: 4096 (order: 12, 16384 bytes) > Detected 2393.969 MHz processor. > Console: colour VGA+ 80x25 > console [tty0] enabled > Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar > ... MAX_LOCKDEP_SUBCLASSES: 8 > ... MAX_LOCK_DEPTH: 30 > ... MAX_LOCKDEP_KEYS: 2048 > ... CLASSHASH_SIZE: 1024 > ... MAX_LOCKDEP_ENTRIES: 8192 > ... MAX_LOCKDEP_CHAINS: 16384 > ... CHAINHASH_SIZE: 8192 > memory used by lock dependency info: 1024 kB > per task-struct memory footprint: 1680 bytes > Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) > Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) > Memory: 2062060k/2087616k available (2235k kernel code, 24476k reserved, 1229k > data, 560k init, 1170112k highmem) > virtual kernel memory layout: > fixmap : 0xffee4000 - 0xfffff000 (1132 kB) > pkmap : 0xff800000 - 0xffc00000 (4096 kB) > vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) > lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) > .init : 0xc0469000 - 0xc04f5000 ( 560 kB) > .data : 0xc032ec36 - 0xc04621c4 (1229 kB) > .text : 0xc0100000 - 0xc032ec36 (2235 kB) > Checking if this processor honours the WP bit even in supervisor mode... Ok. > hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 > hpet0: 3 64-bit timers, 14318180 Hz > Calibrating delay using timer specific routine.. 4795.10 BogoMIPS > (lpj=9590211) > Security Framework v1.0.0 initialized > SELinux: Initializing. > SELinux: Starting in permissive mode > Mount-cache hash table entries: 512 > CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 > 0000e3bd 00000000 00000001 00000001 > monitor/mwait feature present. > using mwait in idle threads. > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 4096K > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 0 > CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd > 00000000 00000001 00000001 > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > Compat vDSO mapped to ffffe000. > Checking 'hlt' instruction... OK. > lockdep: not fixing up alternatives. > ACPI: Core revision 20070126 > Parsing all Control Methods: > Table [DSDT](id 0001) - 1019 Objects with 94 Devices 235 Methods 38 Regions > Parsing all Control Methods: > Table [SSDT](id 0002) - 12 Objects with 3 Devices 4 Methods 0 Regions > Parsing all Control Methods: > Table [SSDT](id 0003) - 13 Objects with 3 Devices 5 Methods 0 Regions > Parsing all Control Methods: > Table [SSDT](id 0004) - 5 Objects with 0 Devices 3 Methods 0 Regions > Parsing all Control Methods: > Table [SSDT](id 0005) - 7 Objects with 0 Devices 3 Methods 0 Regions > Parsing all Control Methods: > Table [SSDT](id 0006) - 4 Objects with 0 Devices 3 Methods 0 Regions > Parsing all Control Methods: > Table [SSDT](id 0007) - 13 Objects with 0 Devices 4 Methods 0 Regions > tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired > evxfevnt-0091 [00] enable : Transition to ACPI mode successful > CPU0: Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz stepping 0b > lockdep: not fixing up alternatives. > Booting processor 1/1 eip 3000 > Initializing CPU#1 > Calibrating delay using timer specific routine.. 4787.88 BogoMIPS > (lpj=9575775) > CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 > 0000e3bd 00000000 00000001 00000001 > monitor/mwait feature present. > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 4096K > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 1 > CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd > 00000000 00000001 00000001 > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#1. > CPU1: Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz stepping 0b > Total of 2 processors activated (9582.99 BogoMIPS). > ENABLING IO-APIC IRQs > ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 > checking TSC synchronization [CPU#0 -> CPU#1]: passed. > Brought up 2 CPUs > Booting paravirtualized kernel on bare hardware > NET: Registered protocol family 16 > ACPI: bus type pci registered > PCI: Using MMCONFIG > Setting up standard PCI resources > evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int > 0x9 > evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 8 Wake, Enabled 5 Runtime > GPEs in this block > ACPI: EC: Look up EC in DSDT > ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62 > Completing Region/Field/Buffer/Package > initialization:................................................................................ > Initialized 36/38 Regions 0/0 Fields 27/28 Buffers 17/46 Packages (1082 nodes) > Initializing Device/Processor/Thermal objects by executing _INI > methods:<4>ACPI: System BIOS is requesting _OSI(Linux) > ACPI: If "acpi_osi=Linux" works better, > Please send dmidecode to linux-acpi@xxxxxxxxxxxxxxx > . > Executed 1 _INI methods requiring 0 _STA executions (examined 107 objects) > ACPI: Interpreter enabled > ACPI: (supports S0 S3 S4 S5) > ACPI: Using IOAPIC for interrupt routing > ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62 > ACPI: PCI Root Bridge [PCI0] (0000:00) > PCI: Transparent bridge - 0000:00:1e.0 > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] > ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15) > ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 > ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15) > ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 > ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15) > ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 > ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15) > ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI init > ACPI: bus type pnp registered > pnp: PnP ACPI: found 12 devices > ACPI: ACPI bus type pnp unregistered > SCSI subsystem initialized > libata version 2.21 loaded. > PCI: Using ACPI for IRQ routing > PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report > NetLabel: Initializing > NetLabel: domain hash size = 128 > NetLabel: protocols = UNLABELED CIPSOv4 > NetLabel: unlabeled traffic allowed by default > ACPI: RTC can wake from S4 > Time: tsc clocksource has been installed. > pnp: 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved > pnp: 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved > pnp: 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved > pnp: 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved > PCI: Bridge: 0000:00:1c.0 > IO window: 2000-2fff > MEM window: f6000000-f7ffffff > PREFETCH window: f0000000-f1ffffff > PCI: Bridge: 0000:00:1c.1 > IO window: 3000-3fff > MEM window: f8000000-f9ffffff > PREFETCH window: f2000000-f3ffffff > PCI: Bridge: 0000:00:1c.2 > IO window: 4000-4fff > MEM window: fa000000-fbffffff > PREFETCH window: f4000000-f5ffffff > PCI: Bridge: 0000:00:1c.3 > IO window: 5000-5fff > MEM window: c8000000-c9ffffff > PREFETCH window: cc000000-cdffffff > PCI: Bus 10, cardbus bridge: 0000:09:04.0 > IO window: 00006000-000060ff > IO window: 00006400-000064ff > PREFETCH window: 88000000-8bffffff > MEM window: 90000000-93ffffff > PCI: Bridge: 0000:00:1e.0 > IO window: 6000-6fff > MEM window: fc200000-fc2fffff > PREFETCH window: 88000000-8bffffff > ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 > PCI: Setting latency timer of device 0000:00:1c.0 to 64 > ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17 > PCI: Setting latency timer of device 0000:00:1c.1 to 64 > ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18 > PCI: Setting latency timer of device 0000:00:1c.2 to 64 > ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19 > PCI: Setting latency timer of device 0000:00:1c.3 to 64 > PCI: Setting latency timer of device 0000:00:1e.0 to 64 > ACPI: PCI Interrupt 0000:09:04.0[A] -> GSI 20 (level, low) -> IRQ 20 > NET: Registered protocol family 2 > IP route cache hash table entries: 32768 (order: 5, 131072 bytes) > TCP established hash table entries: 65536 (order: 9, 2621440 bytes) > TCP bind hash table entries: 65536 (order: 9, 2359296 bytes) > TCP: Hash tables configured (established 65536 bind 65536) > TCP reno registered > Simple Boot Flag at 0x36 set to 0x1 > audit: initializing netlink socket (disabled) > audit(1195124180.432:1): initialized > highmem bounce pool size: 64 pages > Total HugeTLB memory allocated, 0 > VFS: Disk quotas dquot_6.5.1 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > SELinux: Registering netfilter hooks > io scheduler noop registered > io scheduler anticipatory registered (default) > io scheduler deadline registered > io scheduler cfq registered > Boot video device is 0000:00:02.0 > PCI: Setting latency timer of device 0000:00:1c.0 to 64 > assign_interrupt_mode Found MSI capability > Allocate Port Service[0000:00:1c.0:pcie00] > Allocate Port Service[0000:00:1c.0:pcie02] > Allocate Port Service[0000:00:1c.0:pcie03] > PCI: Setting latency timer of device 0000:00:1c.1 to 64 > assign_interrupt_mode Found MSI capability > Allocate Port Service[0000:00:1c.1:pcie00] > Allocate Port Service[0000:00:1c.1:pcie02] > Allocate Port Service[0000:00:1c.1:pcie03] > PCI: Setting latency timer of device 0000:00:1c.2 to 64 > assign_interrupt_mode Found MSI capability > Allocate Port Service[0000:00:1c.2:pcie00] > Allocate Port Service[0000:00:1c.2:pcie02] > Allocate Port Service[0000:00:1c.2:pcie03] > PCI: Setting latency timer of device 0000:00:1c.3 to 64 > assign_interrupt_mode Found MSI capability > Allocate Port Service[0000:00:1c.3:pcie00] > Allocate Port Service[0000:00:1c.3:pcie02] > Allocate Port Service[0000:00:1c.3:pcie03] > ACPI: AC Adapter [ACAD] (on-line) > ACPI: Battery Slot [BAT1] (battery present) > ACPI: SSDT 7F6BF57E, 02BC (r1 Sony VAIO 20070712 PTL 20050624) > Parsing all Control Methods: > Table [SSDT](id 002D) - 6 Objects with 0 Devices 3 Methods 0 Regions > ACPI: SSDT 7F6BF017, 04E2 (r1 Sony VAIO 20070712 PTL 20050624) > Parsing all Control Methods: > Table [SSDT](id 002E) - 1 Objects with 0 Devices 1 Methods 0 Regions > Monitor-Mwait will be used to enter C-1 state > Monitor-Mwait will be used to enter C-2 state > Monitor-Mwait will be used to enter C-3 state > ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > ACPI: Processor [CPU0] (supports 8 throttling states) > ACPI: SSDT 7F6BF83A, 00C8 (r1 Sony VAIO 20070712 PTL 20050624) > Parsing all Control Methods: > Table [SSDT](id 0039) - 4 Objects with 0 Devices 4 Methods 0 Regions > ACPI: SSDT 7F6BF4F9, 0085 (r1 Sony VAIO 20070712 PTL 20050624) > Parsing all Control Methods: > Table [SSDT](id 003A) - 1 Objects with 0 Devices 1 Methods 0 Regions > ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) > ACPI: Processor [CPU1] (supports 8 throttling states) > Marking TSC unstable due to: possible TSC halt in C2. > Time: hpet clocksource has been installed. > ACPI: Thermal Zone [ATF0] (28 C) > Switched to high resolution mode on CPU 0 > Switched to high resolution mode on CPU 1 > ACPI: Thermal Zone [DTS0] (27 C) > ACPI: Thermal Zone [DTS1] (26 C) > hpet_resources: 0xfed00000 is busy > Linux agpgart interface v0.102 > agpgart: Detected an Intel 965GM Chipset. > agpgart: Detected 7676K stolen memory. > agpgart: AGP aperture is 256M @ 0xd0000000 > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled > RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize > netconsole: not configured, aborting > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > ICH8M: IDE controller at PCI slot 0000:00:1f.1 > ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 21 > ICH8M: chipset revision 3 > ICH8M: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0x1818-0x181f, BIOS settings: hdc:pio, hdd:pio > Probing IDE interface ide0... > Clocksource tsc unstable (delta = -358258157 ns) > hda: MATSHITADVD-RAM UJ-852S, ATAPI CD/DVD-ROM drive > hda: selected mode 0x42 > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > Probing IDE interface ide1... > Probing IDE interface ide1... > ata_piix 0000:00:1f.2: version 2.12 > ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] > ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 22 (level, low) -> IRQ 21 > PCI: Setting latency timer of device 0000:00:1f.2 to 64 > scsi0 : ata_piix > scsi1 : ata_piix > ata1: SATA max UDMA/133 cmd 0x00011c00 ctl 0x000118f6 bmdma 0x000118e0 irq 21 > ata2: SATA max UDMA/133 cmd 0x000118f8 ctl 0x000118f2 bmdma 0x000118e8 irq 21 > ata1.00: ATA-7: TOSHIBA MK2035GSS, DK022A, max UDMA/100 > ata1.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata1.00: configured for UDMA/100 > scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK2035GS DK02 PQ: 0 ANSI: 5 > sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB) > sd 0:0:0:0: [sda] Write Protect is off > sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support > DPO or FUA > sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors (200050 MB) > sd 0:0:0:0: [sda] Write Protect is off > sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support > DPO or FUA > sda: sda1 sda2 sda3 < sda5 sda6 > > sd 0:0:0:0: [sda] Attached SCSI disk > PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > serio: i8042 AUX port at 0x60,0x64 irq 12 > mice: PS/2 mouse device common for all mice > input: AT Translated Set 2 keyboard as /class/input/input0 > TCP cubic registered > NET: Registered protocol family 1 > NET: Registered protocol family 17 > Starting balanced_irq > Using IPI No-Shortcut mode > kjournald starting. Commit interval 5 seconds > EXT3-fs: mounted filesystem with ordered data mode. > VFS: Mounted root (ext3 filesystem) readonly. > Freeing unused kernel memory: 560k freed > Real Time Clock Driver v1.12ac > ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 22 (level, low) -> IRQ 21 > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 20 (level, low) -> IRQ 20 > PCI: Setting latency timer of device 0000:00:1a.7 to 64 > ehci_hcd 0000:00:1a.7: EHCI Host Controller > ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 > ehci_hcd 0000:00:1a.7: debug port 1 > PCI: cache line size of 32 is not supported by device 0000:00:1a.7 > ehci_hcd 0000:00:1a.7: irq 20, io mem 0xfc504000 > ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 4 ports detected > USB Universal Host Controller Interface driver v3.0 > input: Video Bus as /class/input/input1 > ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) > input: Power Button (CM) as /class/input/input2 > ACPI: Power Button (CM) [PWRB] > input: Lid Switch as /class/input/input3 > ACPI: Lid Switch [LID0] > ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 20 (level, low) -> IRQ 20 > PCI: Setting latency timer of device 0000:00:1a.0 to 64 > uhci_hcd 0000:00:1a.0: UHCI Host Controller > uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 2 > uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 2 ports detected > sd 0:0:0:0: Attached scsi generic sg0 type 0 > sony-laptop: Sony Programmable IO Control Driver v0.5. > sony-laptop: detected Type2 model > input: Sony Vaio Keys as /class/input/input4 > input: Sony Vaio Jogdial as /class/input/input5 > sony-laptop: device allocated minor is 62 > ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 20 (level, low) -> IRQ 20 > PCI: Setting latency timer of device 0000:00:1a.1 to 64 > uhci_hcd 0000:00:1a.1: UHCI Host Controller > uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 3 > uhci_hcd 0000:00:1a.1: irq 20, io base 0x00001840 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 2 ports detected > input: PS/2 Mouse as /class/input/input6 > input: AlpsPS/2 ALPS GlidePoint as /class/input/input7 > sony-laptop: Sony Notebook Control Driver v0.5. > ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 22 > PCI: Setting latency timer of device 0000:00:1d.0 to 64 > uhci_hcd 0000:00:1d.0: UHCI Host Controller > uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4 > uhci_hcd 0000:00:1d.0: irq 22, io base 0x00001860 > usb usb4: configuration #1 chosen from 1 choice > hub 4-0:1.0: USB hub found > hub 4-0:1.0: 2 ports detected > hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) > Uniform CD-ROM driver Revision: 3.20 > ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 23 (level, low) -> IRQ 22 > PCI: Setting latency timer of device 0000:00:1d.1 to 64 > uhci_hcd 0000:00:1d.1: UHCI Host Controller > uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5 > uhci_hcd 0000:00:1d.1: irq 22, io base 0x00001880 > usb usb5: configuration #1 chosen from 1 choice > hub 5-0:1.0: USB hub found > hub 5-0:1.0: 2 ports detected > ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 23 (level, low) -> IRQ 22 > PCI: Setting latency timer of device 0000:00:1d.2 to 64 > uhci_hcd 0000:00:1d.2: UHCI Host Controller > uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6 > uhci_hcd 0000:00:1d.2: irq 22, io base 0x000018a0 > usb usb6: configuration #1 chosen from 1 choice > hub 6-0:1.0: USB hub found > hub 6-0:1.0: 2 ports detected > usb 1-2: new high speed USB device using ehci_hcd and address 3 > ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 22 > PCI: Setting latency timer of device 0000:00:1d.7 to 64 > ehci_hcd 0000:00:1d.7: EHCI Host Controller > ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7 > ehci_hcd 0000:00:1d.7: debug port 1 > PCI: cache line size of 32 is not supported by device 0000:00:1d.7 > ehci_hcd 0000:00:1d.7: irq 22, io mem 0xfc504400 > ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > usb usb7: configuration #1 chosen from 1 choice > hub 7-0:1.0: USB hub found > hub 7-0:1.0: 6 ports detected > ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 18 (level, low) -> IRQ 18 > PCI: Setting latency timer of device 0000:07:00.0 to 64 > sky2 0000:07:00.0: v1.18 addr 0xfa000000 irq 18 Yukon-EC Ultra (0xb4) rev 3 > sky2 eth0: addr 00:1a:80:56:69:98 > ACPI: PCI Interrupt 0000:09:04.2[C] -> GSI 22 (level, low) -> IRQ 21 > Yenta: CardBus bridge found at 0000:09:04.0 [104d:9008] > Yenta: Enabling burst memory read transactions > Yenta: Using CSCINT to route CSC interrupts to PCI > Yenta: Routing CardBus interrupts to PCI > Yenta TI: socket 0000:09:04.0, mfunc 0x01a21b22, devctl 0x64 > ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 23 > PCI: Setting latency timer of device 0000:00:1b.0 to 64 > usb 1-2: configuration #1 chosen from 1 choice > Yenta: ISA IRQ mask 0x0cb8, PCI irq 20 > Socket status: 30000006 > Yenta: Raising subordinate bus# of parent bus (#09) from #0a to #0d > pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff > cs: IO port probe 0x6000-0x6fff: clean. > pcmcia: parent PCI bridge Memory window: 0xfc200000 - 0xfc2fffff > pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff > ACPI: PCI Interrupt 0000:09:04.1[B] -> GSI 21 (level, low) -> IRQ 23 > usb 2-1: new full speed USB device using uhci_hcd and address 2 > ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[23] MMIO=[fc206000-fc2067ff] > Max Packet=[2048] IR/IT contexts=[4/8] > usb 2-1: configuration #1 chosen from 1 choice > usb 7-1: new high speed USB device using ehci_hcd and address 2 > usb 7-1: configuration #1 chosen from 1 choice > hub 7-1:1.0: USB hub found > hub 7-1:1.0: 4 ports detected > ieee1394: Host added: ID:BUS[0-00:1023] GUID[080046030292f887] > EXT3 FS on sda6, internal journal > usbcore: registered new interface driver snd-usb-audio > device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: > dm-devel@xxxxxxxxxx > Adding 2002836k swap on /dev/sda5. Priority:-1 extents:1 across:2002836k > sky2 eth0: enabling interface > sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both > NET: Registered protocol family 10 > lo: Disabled Privacy Extensions > eth0: no IPv6 routers present > > > > > > > > > > > > lspci -vv > 00:00.0 Host bridge: Intel Corporation Mobile Memory Controller Hub (rev 0c) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ >SERR- <PERR- INTx- > Latency: 0 > Capabilities: [e0] Vendor Specific Information > > 00:02.0 VGA compatible controller: Intel Corporation Mobile Integrated > Graphics Controller (rev 0c) (prog-if 00 [VGA]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 10 > Region 0: Memory at fc000000 (64-bit, non-prefetchable) [size=1M] > Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] > Region 4: I/O ports at 1800 [size=8] > Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- > Queue=0/0 Enable- > Address: 00000000 Data: 0000 > Capabilities: [d0] Power Management version 3 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Bridge: PM- B3+ > > 00:02.1 Display controller: Intel Corporation Mobile Integrated Graphics > Controller (rev 0c) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Region 0: Memory at fc100000 (64-bit, non-prefetchable) [size=1M] > Capabilities: [d0] Power Management version 3 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Bridge: PM- B3+ > > 00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI > Contoller #4 (rev 03) (prog-if 00 [UHCI]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 20 > Region 4: I/O ports at 1820 [size=32] > > 00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI > Controller #5 (rev 03) (prog-if 00 [UHCI]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin B routed to IRQ 20 > Region 4: I/O ports at 1840 [size=32] > > 00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI > Controller #2 (rev 03) (prog-if 20 [EHCI]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin C routed to IRQ 20 > Region 0: Memory at fc504000 (32-bit, non-prefetchable) [size=1K] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Debug port > > 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio > Controller (rev 03) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 23 > Region 0: Memory at fc500000 (64-bit, non-prefetchable) [size=16K] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ > Queue=0/0 Enable- > Address: 0000000000000000 Data: 0000 > Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI > 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, > L1 <1us > ExtTag- RBE- FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, > Latency L0 <64ns, L1 <1us > ClockPM- Suprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- > DLActive- BWMgmt- ABWMgmt- > Capabilities: [100] Virtual Channel > Capabilities: [130] Root Complex Link > > 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 > (rev 03) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=02, subordinate=05, sec-latency=0 > I/O behind bridge: 00002000-00002fff > Memory behind bridge: f6000000-f7ffffff > Prefetchable memory behind bridge: 00000000f0000000-00000000f1ffffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s > unlimited, L1 unlimited > ExtTag- RBE+ FLReset- > DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ > Unsupported+ > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency > L0 <1us, L1 <4us > ClockPM- Suprise- LLActRep+ BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- > CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ > Surpise+ > Slot # 2, PowerLimit 6.500000; Interlock- NoCompl- > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- > LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- > Interlock- > Changed: MRL- PresDet- LinkState- > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- > Queue=0/0 Enable+ > Address: fee0300c Data: 41d1 > Capabilities: [90] Subsystem: Sony Corporation Unknown device 9008 > Capabilities: [a0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [100] Virtual Channel > Capabilities: [180] Root Complex Link > > 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 > (rev 03) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 > I/O behind bridge: 00003000-00003fff > Memory behind bridge: f8000000-f9ffffff > Prefetchable memory behind bridge: 00000000f2000000-00000000f3ffffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s > unlimited, L1 unlimited > ExtTag- RBE+ FLReset- > DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ > Unsupported+ > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency > L0 <256ns, L1 <4us > ClockPM- Suprise- LLActRep+ BwNot- > LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- > CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive+ BWMgmt- ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ > Surpise+ > Slot # 3, PowerLimit 6.500000; Interlock- NoCompl- > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- > LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ > Interlock- > Changed: MRL- PresDet- LinkState- > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- > Queue=0/0 Enable+ > Address: fee0300c Data: 41d9 > Capabilities: [90] Subsystem: Sony Corporation Unknown device 9008 > Capabilities: [a0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [100] Virtual Channel > Capabilities: [180] Root Complex Link > > 00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 > (rev 03) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 > I/O behind bridge: 00004000-00004fff > Memory behind bridge: fa000000-fbffffff > Prefetchable memory behind bridge: 00000000f4000000-00000000f5ffffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s > unlimited, L1 unlimited > ExtTag- RBE+ FLReset- > DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ > Unsupported+ > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency > L0 <256ns, L1 <4us > ClockPM- Suprise- LLActRep+ BwNot- > LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- > CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive+ BWMgmt- ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ > Surpise+ > Slot # 4, PowerLimit 6.500000; Interlock- NoCompl- > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- > LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ > Interlock- > Changed: MRL- PresDet- LinkState- > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- > Queue=0/0 Enable+ > Address: fee0300c Data: 41e1 > Capabilities: [90] Subsystem: Sony Corporation Unknown device 9008 > Capabilities: [a0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [100] Virtual Channel > Capabilities: [180] Root Complex Link > > 00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 > (rev 03) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 > I/O behind bridge: 00005000-00005fff > Memory behind bridge: c8000000-c9ffffff > Prefetchable memory behind bridge: 00000000cc000000-00000000cdffffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s > unlimited, L1 unlimited > ExtTag- RBE+ FLReset- > DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ > Unsupported+ > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency > L0 <1us, L1 <4us > ClockPM- Suprise- LLActRep+ BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- > CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ > Surpise+ > Slot # 5, PowerLimit 6.500000; Interlock- NoCompl- > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- > LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- > Interlock- > Changed: MRL- PresDet- LinkState- > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- > Queue=0/0 Enable+ > Address: fee0300c Data: 41e9 > Capabilities: [90] Subsystem: Sony Corporation Unknown device 9008 > Capabilities: [a0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [100] Virtual Channel > Capabilities: [180] Root Complex Link > > 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI > Controller #1 (rev 03) (prog-if 00 [UHCI]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 22 > Region 4: I/O ports at 1860 [size=32] > > 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI > Controller #2 (rev 03) (prog-if 00 [UHCI]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin B routed to IRQ 22 > Region 4: I/O ports at 1880 [size=32] > > 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI > Controller #3 (rev 03) (prog-if 00 [UHCI]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin C routed to IRQ 22 > Region 4: I/O ports at 18a0 [size=32] > > 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI > Controller #1 (rev 03) (prog-if 20 [EHCI]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin D routed to IRQ 22 > Region 0: Memory at fc504400 (32-bit, non-prefetchable) [size=1K] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME+ > Capabilities: [58] Debug port > > 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3) > (prog-if 01 [Subtractive decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Bus: primary=00, secondary=09, subordinate=0d, sec-latency=32 > I/O behind bridge: 00006000-00006fff > Memory behind bridge: fc200000-fc2fffff > Prefetchable memory behind bridge: 0000000088000000-000000008bffffff > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [50] Subsystem: Sony Corporation Unknown device 9008 > > 00:1f.0 ISA bridge: Intel Corporation Mobile LPC Interface Controller (rev 03) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Capabilities: [e0] Vendor Specific Information > > 00:1f.1 IDE interface: Intel Corporation Mobile IDE Controller (rev 03) > (prog-if 8a [Master SecP PriP]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 21 > Region 0: I/O ports at 01f0 [size=8] > Region 1: I/O ports at 03f4 [size=1] > Region 2: I/O ports at 0170 [size=8] > Region 3: I/O ports at 0374 [size=1] > Region 4: I/O ports at 1810 [size=16] > > 00:1f.2 IDE interface: Intel Corporation Mobile SATA IDE Controller (rev 03) > (prog-if 8f [Master SecP SecO PriP PriO]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin B routed to IRQ 21 > Region 0: I/O ports at 1c00 [size=8] > Region 1: I/O ports at 18f4 [size=4] > Region 2: I/O ports at 18f8 [size=8] > Region 3: I/O ports at 18f0 [size=4] > Region 4: I/O ports at 18e0 [size=16] > Region 5: I/O ports at 18d0 [size=16] > Capabilities: [70] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot+,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev > 03) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin C routed to IRQ 21 > Region 0: Memory at 8c000000 (32-bit, non-prefetchable) [size=256] > Region 4: I/O ports at 1c20 [size=32] > > 06:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network > Connection (rev 02) > Subsystem: Intel Corporation Unknown device 1051 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 10 > Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [c8] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ > Queue=0/0 Enable- > Address: 0000000000000000 Data: 0000 > Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, > L1 unlimited > ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ > TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency > L0 <128ns, L1 <64us > ClockPM+ Suprise- LLActRep- BwNot- > LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- > CommClk+ > ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > Capabilities: [100] Advanced Error Reporting > Capabilities: [140] Device Serial Number 7a-db-ff-ff-77-1b-00-00 > > 07:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8055 PCI-E > Gigabit Ethernet Controller (rev 12) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 219 > Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=16K] > Region 2: I/O ports at 4000 [size=256] > [virtual] Expansion ROM at f4000000 [disabled] [size=128K] > Capabilities: [48] Power Management version 3 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=1 PME- > Capabilities: [50] Vital Product Data > Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ > Queue=0/0 Enable+ > Address: 00000000fee0300c Data: 4142 > Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s > unlimited, L1 unlimited > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 512 bytes > DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ > TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency > L0 <256ns, L1 unlimited > ClockPM+ Suprise- LLActRep- BwNot- > LnkCtl: ASPM L0s L1 Enabled; RCB 128 bytes Disabled- Retrain- > CommClk+ > ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > Capabilities: [100] Advanced Error Reporting > > 09:04.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 168, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 20 > Region 0: Memory at fc204000 (32-bit, non-prefetchable) [size=4K] > Bus: primary=09, secondary=0a, subordinate=0d, sec-latency=176 > Memory window 0: 88000000-8bfff000 (prefetchable) > Memory window 1: 90000000-93fff000 > I/O window 0: 00006000-000060ff > I/O window 1: 00006400-000064ff > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ > 16-bit legacy interface ports at 0001 > > 09:04.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE > 1394 Host Controller (prog-if 10 [OHCI]) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 32 (750ns min, 1000ns max), Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 23 > Region 0: Memory at fc206000 (32-bit, non-prefetchable) [size=2K] > Region 1: Memory at fc200000 (32-bit, non-prefetchable) [size=16K] > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA > PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME+ > > 09:04.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card > Reader (SD/MMC/MS/MS PRO/xD) > Subsystem: Sony Corporation Unknown device 9008 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 57 (1750ns min, 1000ns max), Cache Line Size: 64 bytes > Interrupt: pin C routed to IRQ 21 > Region 0: Memory at fc205000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0+,D1+,D2+,D3hot+,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > - > To unsubscribe from this list: send the line "unsubscribe linux-acpi" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html - To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
