Hello linux-acpi
I'm sending this email in response to this message in my computers dmesg
log:
ACPI: Please test with "acpi_osi=!Linux"
Please send dmidecode to linux-acpi@xxxxxxxxxxxxxxx
I've installed Ubuntu 7.10 on this laptop, which is an Acer TravelMate
7513WSMi. I've upgraded to the latest BIOS (v1.19).
Ubuntu is mostly working, although sound only works through headphones,
and some types of memory card aren't detected properly. I haven't
tested everything yet.
After selecting the standard kernel from the Grub menu, I get the
following error messages:
BIOS BUG #81[00000000] found
Cannot allocate resource region 7 of bridge 0000:00:04.0
Cannot allocate resource region 5 of device 0000:03:00.0
Failed to allocate mem resource #6:20000@00000000 for 0000:03:00.0
The first of those message goes away if I use 'pci=conf1'.
The other three are unaffected by 'noacpi' or 'acpi_osi=!Linux'.
As requested, I've attached dmidecode output, as well as that from dmesg
and lspci -vvv. The second dmesg file is the output when using
'acpi_osi=!Linux' as suggested.
I hope this information is helpful for future kernel development. And
if you have any suggestions for getting rid of these error messages on
my laptop, I'd be very grateful to receive them.
regards
Chris
--
Chris Dennis email: chris@xxxxxxxxxxx
Fordingbridge Computer Services web: http://www.fb-cs.co.uk
Phone: (01425) 658265 Mobile: 07814 239534
[ 0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[ 0.000000] BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003ff10000 (usable)
[ 0.000000] BIOS-e820: 000000003ff10000 - 000000003ff1a000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003ff1a000 - 000000003ff80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f81a0
[ 0.000000] Entering add_active_range(0, 0, 261904) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 261904
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 261904
[ 0.000000] On node 0 totalpages: 261904
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 254 pages used for memmap
[ 0.000000] HighMem zone: 32274 pages, LIFO batch:7
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F8230 checksum 0
[ 0.000000] ACPI: RSDP 000F8230, 0024 (r3 PTLTD )
[ 0.000000] ACPI: XSDT 3FF138C9, 005C (r1 ACRSYS ACRPRDCT 6040000 INNA 0)
[ 0.000000] ACPI: FACP 3FF19AA6, 00F4 (r3 NVIDIA MCP51M 6040000 PTL F4240)
[ 0.000000] ACPI: DSDT 3FF13925, 6181 (r1 NVIDIA MCP51M 6040000 MSFT 100000E)
[ 0.000000] ACPI: FACS 3FF1AFC0, 0040
[ 0.000000] ACPI: SLIC 3FF19C0E, 0176 (r1 ACRSYS ACRPRDCT 6040000 ANNI 1)
[ 0.000000] ACPI: MCFG 3FF19D84, 003C (r1 PTLTD MCFG 6040000 LTP 0)
[ 0.000000] ACPI: HPET 3FF19DC0, 0038 (r1 PTLTD HPETTBL 6040000 LTP 1)
[ 0.000000] ACPI: APIC 3FF19DF8, 005E (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: BOOT 3FF19E56, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: SSDT 3FF19E7E, 0182 (r1 PTLTD POWERNOW 6040000 LTP 1)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] Built 1 zonelists. Total pages: 259858
[ 0.000000] Kernel command line: root=UUID=76b2d2e0-db08-436e-adb2-f82378c0b556 ro quiet splash
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1607.313 MHz processor.
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1026976k/1047616k available (2015k kernel code, 19968k reserved, 916k data, 364k init, 130112k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.000000] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 0.000000] .data : 0xc02f7d26 - 0xc03dce84 ( 916 kB)
[ 0.000000] .text : 0xc0100000 - 0xc02f7d26 (2015 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 0.000000] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 0.000000] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 0.000000] hpet0: 3 32-bit timers, 25000000 Hz
[ 0.080000] Calibrating delay using timer specific routine.. 3217.47 BogoMIPS (lpj=6434955)
[ 0.080000] Security Framework v1.0.0 initialized
[ 0.080000] SELinux: Disabled at boot.
[ 0.080000] Mount-cache hash table entries: 512
[ 0.080000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 0.080000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.080000] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.080000] CPU 0(2) -> Core 0
[ 0.080000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 0.080000] Compat vDSO mapped to ffffe000.
[ 0.080000] Checking 'hlt' instruction... OK.
[ 0.096000] SMP alternatives: switching to UP code
[ 0.096000] Early unpacking initramfs... done
[ 0.456000] ACPI: Core revision 20070126
[ 0.456000] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 0.460000] CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02
[ 0.460000] SMP alternatives: switching to SMP code
[ 0.460000] Booting processor 1/1 eip 3000
[ 0.472000] Initializing CPU#1
[ 0.552000] Calibrating delay using timer specific routine.. 3214.65 BogoMIPS (lpj=6429315)
[ 0.552000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 0.552000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.552000] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.552000] CPU 1(2) -> Core 1
[ 0.552000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 0.552000] CPU1: AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02
[ 0.552000] Total of 2 processors activated (6432.13 BogoMIPS).
[ 0.552000] ENABLING IO-APIC IRQs
[ 0.552000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.592000] Brought up 2 CPUs
[ 0.608000] migration_cost=4000
[ 0.608000] Booting paravirtualized kernel on bare hardware
[ 0.608000] Time: 13:01:32 Date: 10/12/107
[ 0.608000] NET: Registered protocol family 16
[ 0.608000] EISA bus registered
[ 0.608000] ACPI: bus type pci registered
[ 0.620000] PCI: BIOS BUG #81[49435000] found
[ 0.620000] PCI: Using configuration type 1
[ 0.620000] Setting up standard PCI resources
[ 0.620000] ACPI: EC: Look up EC in DSDT
[ 0.624000] ACPI: EC: GPE=0x01, ports=0x66, 0x62
[ 0.624000] ACPI: System BIOS is requesting _OSI(Linux)
[ 0.624000] ACPI: Please test with "acpi_osi=!Linux"
[ 0.624000] Please send dmidecode to linux-acpi@xxxxxxxxxxxxxxx
[ 0.624000] ACPI: Interpreter enabled
[ 0.624000] ACPI: (supports S0 S3 S4 S5)
[ 0.624000] ACPI: Using IOAPIC for interrupt routing
[ 0.636000] ACPI: EC: GPE=0x01, ports=0x66, 0x62
[ 0.636000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.636000] PCI: Probing PCI hardware (bus 00)
[ 0.636000] PCI: Transparent bridge - 0000:00:10.0
[ 0.636000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.636000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[ 0.636000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
[ 0.636000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
[ 0.636000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
[ 0.672000] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.672000] ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19 20 21 22 23) *10
[ 0.672000] ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19 20 21 22 23) *10
[ 0.672000] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 *11 14 15)
[ 0.676000] ACPI: PCI Interrupt Link [LK1E] (IRQs 16 17 18 19 20 21 22 23) *10
[ 0.676000] ACPI: PCI Interrupt Link [LK2E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.676000] ACPI: PCI Interrupt Link [LK3E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.676000] ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.676000] ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20 21 22 23) *10
[ 0.676000] ACPI: PCI Interrupt Link [LSMU] (IRQs 16 17 18 19 20 21 22 23) *11
[ 0.676000] ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20 21 22 23) *11
[ 0.676000] ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20 21 22 23) *7
[ 0.676000] ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20 21 22 23) *11
[ 0.676000] ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.676000] ACPI: PCI Interrupt Link [LACI] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.676000] ACPI: PCI Interrupt Link [LMCI] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.676000] ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.676000] ACPI: PCI Interrupt Link [LTID] (IRQs 16 17 18 19 20 21 22 23) *5
[ 0.676000] ACPI: PCI Interrupt Link [LSI1] (IRQs 16 17 18 19 20 21 22 23) *0
[ 0.676000] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.676000] pnp: PnP ACPI init
[ 0.676000] ACPI: bus type pnp registered
[ 0.680000] pnp: PnP ACPI: found 11 devices
[ 0.680000] ACPI: ACPI bus type pnp unregistered
[ 0.680000] PnPBIOS: Disabled by ACPI PNP
[ 0.680000] PCI: Using ACPI for IRQ routing
[ 0.680000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.680000] PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
[ 0.680000] PCI: Cannot allocate resource region 5 of device 0000:03:00.0
[ 0.680000] NET: Registered protocol family 8
[ 0.680000] NET: Registered protocol family 20
[ 0.680000] pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.680000] pnp: 00:02: ioport range 0x1000-0x107f has been reserved
[ 0.680000] pnp: 00:02: ioport range 0x1080-0x10ff has been reserved
[ 0.680000] pnp: 00:02: ioport range 0x1400-0x147f has been reserved
[ 0.680000] pnp: 00:02: ioport range 0x1480-0x14ff has been reserved
[ 0.680000] pnp: 00:02: ioport range 0x1800-0x187f has been reserved
[ 0.680000] pnp: 00:02: ioport range 0x1880-0x18ff has been reserved
[ 0.680000] pnp: 00:02: ioport range 0x2000-0x203f has been reserved
[ 0.684000] Time: hpet clocksource has been installed.
[ 0.712000] PCI: Bridge: 0000:00:02.0
[ 0.712000] IO window: disabled.
[ 0.712000] MEM window: disabled.
[ 0.712000] PREFETCH window: disabled.
[ 0.712000] PCI: Bridge: 0000:00:03.0
[ 0.712000] IO window: 4000-4fff
[ 0.712000] MEM window: c4000000-c40fffff
[ 0.712000] PREFETCH window: disabled.
[ 0.712000] PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:03:00.0
[ 0.712000] PCI: Bridge: 0000:00:04.0
[ 0.712000] IO window: 5000-5fff
[ 0.712000] MEM window: c1000000-c2ffffff
[ 0.712000] PREFETCH window: d0000000-dfffffff
[ 0.712000] PCI: Bus 5, cardbus bridge: 0000:04:06.0
[ 0.712000] IO window: 00006000-000060ff
[ 0.712000] IO window: 00006400-000064ff
[ 0.712000] PREFETCH window: 50000000-53ffffff
[ 0.712000] MEM window: 54000000-57ffffff
[ 0.712000] PCI: Bridge: 0000:00:10.0
[ 0.712000] IO window: 6000-6fff
[ 0.712000] MEM window: c3000000-c30fffff
[ 0.712000] PREFETCH window: 50000000-53ffffff
[ 0.712000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 0.712000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 0.712000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 0.712000] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 0.712000] ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 11
[ 0.712000] ACPI: PCI Interrupt 0000:04:06.0[A] -> Link [LNK4] -> GSI 11 (level, low) -> IRQ 11
[ 0.712000] NET: Registered protocol family 2
[ 0.760000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.760000] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 0.760000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.760000] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.760000] TCP reno registered
[ 0.776000] checking if image is initramfs... it is
[ 1.484000] Freeing initrd memory: 7063k freed
[ 1.484000] Simple Boot Flag at 0x36 set to 0x1
[ 1.484000] audit: initializing netlink socket (disabled)
[ 1.484000] audit(1194872492.184:1): initialized
[ 1.484000] highmem bounce pool size: 64 pages
[ 1.484000] VFS: Disk quotas dquot_6.5.1
[ 1.484000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.484000] io scheduler noop registered
[ 1.484000] io scheduler anticipatory registered
[ 1.484000] io scheduler deadline registered
[ 1.484000] io scheduler cfq registered (default)
[ 1.504000] Boot video device is 0000:03:00.0
[ 1.504000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 1.504000] assign_interrupt_mode Found MSI capability
[ 1.504000] Allocate Port Service[0000:00:02.0:pcie00]
[ 1.504000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 1.504000] assign_interrupt_mode Found MSI capability
[ 1.504000] Allocate Port Service[0000:00:03.0:pcie00]
[ 1.504000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 1.504000] assign_interrupt_mode Found MSI capability
[ 1.504000] Allocate Port Service[0000:00:04.0:pcie00]
[ 1.504000] isapnp: Scanning for PnP cards...
[ 1.856000] isapnp: No Plug & Play device found
[ 1.884000] Real Time Clock Driver v1.12ac
[ 1.884000] hpet_resources: 0xfed00000 is busy
[ 1.884000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.884000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1.884000] input: Macintosh mouse button emulation as /class/input/input0
[ 1.884000] PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.884000] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.884000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.884000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.884000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.884000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.884000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.884000] mice: PS/2 mouse device common for all mice
[ 1.884000] EISA: Probing bus 0 at eisa.0
[ 1.884000] Cannot allocate resource for EISA slot 1
[ 1.884000] Cannot allocate resource for EISA slot 2
[ 1.884000] Cannot allocate resource for EISA slot 3
[ 1.884000] Cannot allocate resource for EISA slot 4
[ 1.884000] Cannot allocate resource for EISA slot 5
[ 1.884000] Cannot allocate resource for EISA slot 6
[ 1.884000] EISA: Detected 0 cards.
[ 1.884000] TCP cubic registered
[ 1.884000] NET: Registered protocol family 1
[ 1.884000] Using IPI No-Shortcut mode
[ 1.884000] Magic number: 15:271:28
[ 1.884000] hash matches device ttydb
[ 1.884000] Freeing unused kernel memory: 364k freed
[ 1.892000] input: AT Translated Set 2 keyboard as /class/input/input1
[ 3.148000] AppArmor: AppArmor initialized<5>audit(1194872494.184:2): type=1505 info="AppArmor initialized" pid=1251
[ 3.156000] fuse init (API version 7.8)
[ 3.164000] Failure registering capabilities with primary security module.
[ 3.204000] ACPI: Thermal Zone [TZS0] (50 C)
[ 3.208000] ACPI: Thermal Zone [TZS1] (53 C)
[ 3.872000] usbcore: registered new interface driver usbfs
[ 3.872000] usbcore: registered new interface driver hub
[ 3.872000] usbcore: registered new device driver usb
[ 3.872000] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 23
[ 3.872000] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUS2] -> GSI 23 (level, high) -> IRQ 16
[ 3.872000] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[ 3.872000] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 3.872000] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
[ 3.872000] ehci_hcd 0000:00:0b.1: debug port 1
[ 3.872000] PCI: cache line size of 64 is not supported by device 0000:00:0b.1
[ 3.872000] ehci_hcd 0000:00:0b.1: irq 16, io mem 0xc0005000
[ 3.872000] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.872000] usb usb1: configuration #1 chosen from 1 choice
[ 3.872000] hub 1-0:1.0: USB hub found
[ 3.872000] hub 1-0:1.0: 8 ports detected
[ 3.876000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 3.876000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 3.888000] SCSI subsystem initialized
[ 3.896000] libata version 2.21 loaded.
[ 3.920000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.976000] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
[ 3.976000] NFORCE-MCP51: chipset revision 241
[ 3.976000] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 3.976000] NFORCE-MCP51: BIOS didn't set cable bits correctly. Enabling workaround.
[ 3.976000] NFORCE-MCP51: 0000:00:0d.0 (rev f1) UDMA133 controller
[ 3.976000] ide0: BM-DMA at 0x3080-0x3087, BIOS settings: hda:pio, hdb:pio
[ 3.976000] ide1: BM-DMA at 0x3088-0x308f, BIOS settings: hdc:DMA, hdd:pio
[ 3.976000] Probing IDE interface ide0...
[ 3.984000] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 4.224000] usb 1-2: new high speed USB device using ehci_hcd and address 2
[ 4.368000] usb 1-2: configuration #1 chosen from 1 choice
[ 4.560000] Probing IDE interface ide1...
[ 4.616000] usb 1-6: new high speed USB device using ehci_hcd and address 3
[ 4.996000] usb 1-6: configuration #1 chosen from 1 choice
[ 5.004000] usbcore: registered new interface driver libusual
[ 5.012000] Initializing USB Mass Storage driver...
[ 5.012000] scsi0 : SCSI emulation for USB Mass Storage devices
[ 5.012000] usb-storage: device found at 2
[ 5.012000] usb-storage: waiting for device to settle before scanning
[ 5.012000] usbcore: registered new interface driver usb-storage
[ 5.012000] USB Mass Storage support registered.
[ 5.296000] hdc: Slimtype DVDRW SSM-8515S, ATAPI CD/DVD-ROM drive
[ 5.968000] ide1 at 0x170-0x177,0x376 on irq 15
[ 5.980000] sata_nv 0000:00:0e.0: version 3.4
[ 5.984000] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 22
[ 5.984000] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LTID] -> GSI 22 (level, high) -> IRQ 17
[ 5.984000] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 5.984000] scsi1 : sata_nv
[ 5.984000] scsi2 : sata_nv
[ 5.984000] ata1: SATA max UDMA/133 cmd 0x000130b0 ctl 0x000130a6 bmdma 0x00013090 irq 17
[ 5.984000] ata2: SATA max UDMA/133 cmd 0x000130a8 ctl 0x000130a2 bmdma 0x00013098 irq 17
[ 6.452000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 6.460000] ata1.00: ATA-7: Hitachi HTS541616J9SA00, SB4OC70P, max UDMA/100
[ 6.460000] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 6.480000] ata1.00: configured for UDMA/100
[ 6.792000] ata2: SATA link down (SStatus 0 SControl 300)
[ 6.796000] scsi 1:0:0:0: Direct-Access ATA Hitachi HTS54161 SB4O PQ: 0 ANSI: 5
[ 6.796000] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 21
[ 6.796000] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 21 (level, high) -> IRQ 18
[ 6.796000] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 6.796000] forcedeth: using HIGHDMA
[ 7.320000] eth0: forcedeth.c: subsystem: 01025:0112 bound to 0000:00:14.0
[ 7.320000] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20
[ 7.320000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUS0] -> GSI 20 (level, high) -> IRQ 19
[ 7.320000] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 7.320000] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 7.320000] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
[ 7.320000] ohci_hcd 0000:00:0b.0: irq 19, io mem 0xc0004000
[ 7.328000] sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 7.328000] sd 1:0:0:0: [sda] Write Protect is off
[ 7.328000] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 7.328000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.328000] sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 7.328000] sd 1:0:0:0: [sda] Write Protect is off
[ 7.328000] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 7.328000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.328000] sda:<6>hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 7.332000] Uniform CD-ROM driver Revision: 3.20
[ 7.356000] sda1 sda2 sda3 <<6>usb usb2: configuration #1 chosen from 1 choice
[ 7.376000] hub 2-0:1.0: USB hub found
[ 7.376000] hub 2-0:1.0: 8 ports detected
[ 7.384000] sda5 sda6 >
[ 7.396000] sd 1:0:0:0: [sda] Attached SCSI disk
[ 7.400000] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 7.744000] Attempting manual resume
[ 7.744000] swsusp: Resume From Partition 8:5
[ 7.744000] PM: Checking swsusp image.
[ 7.744000] PM: Resume from disk failed.
[ 7.780000] kjournald starting. Commit interval 5 seconds
[ 7.780000] EXT3-fs: mounted filesystem with ordered data mode.
[ 10.012000] usb-storage: device scan complete
[ 10.012000] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 10.012000] sd 0:0:0:0: [sdb] 4040192 512-byte hardware sectors (2069 MB)
[ 10.016000] sd 0:0:0:0: [sdb] Write Protect is off
[ 10.016000] sd 0:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 10.016000] sd 0:0:0:0: [sdb] Assuming drive cache: write through
[ 10.020000] sd 0:0:0:0: [sdb] 4040192 512-byte hardware sectors (2069 MB)
[ 10.020000] sd 0:0:0:0: [sdb] Write Protect is off
[ 10.020000] sd 0:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 10.020000] sd 0:0:0:0: [sdb] Assuming drive cache: write through
[ 10.020000] sdb: sdb1
[ 10.024000] sd 0:0:0:0: [sdb] Attached SCSI removable disk
[ 10.024000] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 16.296000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 16.296000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 16.328000] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
[ 16.328000] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
[ 16.636000] ath_hal: module license 'Proprietary' taints kernel.
[ 16.708000] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[ 16.908000] Linux agpgart interface v0.102 (c) Dave Jones
[ 17.144000] wlan: 0.8.4.2 (0.9.3.2)
[ 17.160000] ACPI: PCI Interrupt 0000:04:06.2[A] -> Link [LNK4] -> GSI 11 (level, low) -> IRQ 11
[ 17.192000] Yenta: CardBus bridge found at 0000:04:06.0 [1025:0112]
[ 17.192000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 17.192000] Yenta: Routing CardBus interrupts to PCI
[ 17.192000] Yenta TI: socket 0000:04:06.0, mfunc 0x013a1b22, devctl 0x64
[ 17.428000] Yenta: ISA IRQ mask 0x04f8, PCI irq 11
[ 17.428000] Socket status: 30000006
[ 17.428000] Yenta: Raising subordinate bus# of parent bus (#04) from #05 to #08
[ 17.428000] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 17.428000] cs: IO port probe 0x6000-0x6fff: clean.
[ 17.428000] pcmcia: parent PCI bridge Memory window: 0xc3000000 - 0xc30fffff
[ 17.428000] pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
[ 17.484000] ACPI: PCI Interrupt Link [LK1E] enabled at IRQ 19
[ 17.484000] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LK1E] -> GSI 19 (level, high) -> IRQ 20
[ 17.484000] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 17.484000] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep 12 14:12:24 PDT 2007
[ 17.516000] ath_pci: 0.9.4.5 (0.9.3.2)
[ 17.516000] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 18
[ 17.516000] ACPI: PCI Interrupt 0000:04:05.0[A] -> Link [LNK2] -> GSI 18 (level, high) -> IRQ 21
[ 18.240000] ath_rate_sample: 1.2 (0.9.3.2)
[ 18.244000] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[ 18.244000] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 18.244000] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[ 18.244000] wifi0: mac 7.8 phy 4.5 radio 5.6
[ 18.244000] wifi0: Use hw queue 1 for WME_AC_BE traffic
[ 18.244000] wifi0: Use hw queue 0 for WME_AC_BK traffic
[ 18.244000] wifi0: Use hw queue 2 for WME_AC_VI traffic
[ 18.244000] wifi0: Use hw queue 3 for WME_AC_VO traffic
[ 18.244000] wifi0: Use hw queue 8 for CAB traffic
[ 18.244000] wifi0: Use hw queue 9 for beacons
[ 18.272000] input: PC Speaker as /class/input/input2
[ 18.304000] Linux video capture interface: v2.00
[ 18.376000] wifi0: Atheros 5212: mem=0xc3000000, irq=21
[ 18.448000] uvcvideo: Found UVC 1.00 device USB2.0 Camera (5986:0100)
[ 18.532000] usbcore: registered new interface driver uvcvideo
[ 18.532000] USB Video Class driver (v0.1.0)
[ 18.600000] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 17
[ 18.600000] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 17 (level, high) -> IRQ 22
[ 18.600000] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 18.760000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1280b1, caps: 0xa04713/0x204000
[ 18.784000] cs: IO port probe 0x100-0x3af: clean.
[ 18.788000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 18.788000] cs: IO port probe 0x820-0x8ff: clean.
[ 18.788000] cs: IO port probe 0xc00-0xcf7: clean.
[ 18.788000] cs: IO port probe 0xa00-0xaff: clean.
[ 18.792000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[ 19.328000] loop: module loaded
[ 19.376000] lp: driver loaded but no devices found
[ 19.468000] Adding 2931820k swap on /dev/sda5. Priority:-1 extents:1 across:2931820k
[ 19.908000] EXT3 FS on sda6, internal journal
[ 20.460000] hda_intel: azx_get_response timeout, switching to polling mode...
[ 21.312000] No dock devices found.
[ 21.328000] ACPI: AC Adapter [ADP1] (on-line)
[ 21.440000] input: Power Button (FF) as /class/input/input4
[ 21.440000] ACPI: Power Button (FF) [PWRF]
[ 21.440000] input: Lid Switch as /class/input/input5
[ 21.440000] ACPI: Lid Switch [LID0]
[ 21.440000] input: Sleep Button (CM) as /class/input/input6
[ 21.440000] ACPI: Sleep Button (CM) [SLPB]
[ 21.440000] input: Power Button (CM) as /class/input/input7
[ 21.440000] ACPI: Power Button (CM) [PWRB]
[ 21.608000] ACPI: Battery Slot [BAT0] (battery present)
[ 21.648000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 21.648000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 21.928000] powernow-k8: Found 2 AMD Turion(tm) 64 X2 Mobile Technology TL-52 processors (version 2.00.00)
[ 21.928000] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x13
[ 21.928000] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x1e
[ 23.108000] ppdev: user-space parallel port driver
[ 23.244000] audit(1194872514.754:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5151 profile="/usr/sbin/cupsd"
[ 23.324000] apm: BIOS not found.
[ 23.904000] Failure registering capabilities with primary security module.
[ 24.000000] Clocksource tsc unstable (delta = -112020421 ns)
[ 24.204000] Bluetooth: Core ver 2.11
[ 24.204000] NET: Registered protocol family 31
[ 24.204000] Bluetooth: HCI device and connection manager initialized
[ 24.204000] Bluetooth: HCI socket layer initialized
[ 24.228000] Bluetooth: L2CAP ver 2.8
[ 24.228000] Bluetooth: L2CAP socket layer initialized
[ 24.264000] Bluetooth: RFCOMM socket layer initialized
[ 24.264000] Bluetooth: RFCOMM TTY layer initialized
[ 24.264000] Bluetooth: RFCOMM ver 1.8
[ 28.952000] NET: Registered protocol family 17
[ 32.720000] NET: Registered protocol family 10
[ 32.720000] lo: Disabled Privacy Extensions
[ 42.912000] eth0: no IPv6 routers present
[ 43.412000] ath0: no IPv6 routers present
[ 179.340000] eth0: link down.
[ 1038.848000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 1058.556000] ath0: no IPv6 routers present
[ 2168.312000] usb 1-8: new high speed USB device using ehci_hcd and address 4
[ 2168.448000] usb 1-8: configuration #1 chosen from 1 choice
[ 2168.448000] scsi3 : SCSI emulation for USB Mass Storage devices
[ 2168.448000] usb-storage: device found at 4
[ 2168.448000] usb-storage: waiting for device to settle before scanning
[ 2168.732000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 4 if 1 alt 0 proto 2 vid 0x03F0 pid 0x5711
[ 2168.732000] usbcore: registered new interface driver usblp
[ 2168.732000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 2173.448000] usb-storage: device scan complete
[ 2173.448000] scsi 3:0:0:0: Direct-Access HP Photosmart C4180 1.00 PQ: 0 ANSI: 2
[ 2173.452000] sd 3:0:0:0: [sdc] Attached SCSI removable disk
[ 2173.452000] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 2276.096000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: removed
[ 2276.260000] audit(1194874769.368:4): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=6994 profile="/usr/sbin/cupsd"
[ 2276.304000] audit(1194874769.368:5): type=1503 operation="inode_permission" requested_mask="rw" denied_mask="rw" name="/dev/tty" pid=6997 profile="/usr/sbin/cupsd"
[ 0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[ 0.000000] BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003ff10000 (usable)
[ 0.000000] BIOS-e820: 000000003ff10000 - 000000003ff1a000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003ff1a000 - 000000003ff80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f81a0
[ 0.000000] Entering add_active_range(0, 0, 261904) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 261904
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 261904
[ 0.000000] On node 0 totalpages: 261904
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 254 pages used for memmap
[ 0.000000] HighMem zone: 32274 pages, LIFO batch:7
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F8230 checksum 0
[ 0.000000] ACPI: RSDP 000F8230, 0024 (r3 PTLTD )
[ 0.000000] ACPI: XSDT 3FF138C9, 005C (r1 ACRSYS ACRPRDCT 6040000 INNA 0)
[ 0.000000] ACPI: FACP 3FF19AA6, 00F4 (r3 NVIDIA MCP51M 6040000 PTL F4240)
[ 0.000000] ACPI: DSDT 3FF13925, 6181 (r1 NVIDIA MCP51M 6040000 MSFT 100000E)
[ 0.000000] ACPI: FACS 3FF1AFC0, 0040
[ 0.000000] ACPI: SLIC 3FF19C0E, 0176 (r1 ACRSYS ACRPRDCT 6040000 ANNI 1)
[ 0.000000] ACPI: MCFG 3FF19D84, 003C (r1 PTLTD MCFG 6040000 LTP 0)
[ 0.000000] ACPI: HPET 3FF19DC0, 0038 (r1 PTLTD HPETTBL 6040000 LTP 1)
[ 0.000000] ACPI: APIC 3FF19DF8, 005E (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: BOOT 3FF19E56, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: SSDT 3FF19E7E, 0182 (r1 PTLTD POWERNOW 6040000 LTP 1)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] Built 1 zonelists. Total pages: 259858
[ 0.000000] Kernel command line: root=UUID=76b2d2e0-db08-436e-adb2-f82378c0b556 ro quiet splash acpi_osi=!Linux
[ 0.000000] ACPI: Disabled _OSI(Linux)
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1607.374 MHz processor.
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1026976k/1047616k available (2015k kernel code, 19968k reserved, 916k data, 364k init, 130112k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.000000] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 0.000000] .data : 0xc02f7d26 - 0xc03dce84 ( 916 kB)
[ 0.000000] .text : 0xc0100000 - 0xc02f7d26 (2015 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 0.000000] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 0.000000] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 0.000000] hpet0: 3 32-bit timers, 25000000 Hz
[ 0.080000] Calibrating delay using timer specific routine.. 3217.47 BogoMIPS (lpj=6434943)
[ 0.080000] Security Framework v1.0.0 initialized
[ 0.080000] SELinux: Disabled at boot.
[ 0.080000] Mount-cache hash table entries: 512
[ 0.080000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 0.080000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.080000] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.080000] CPU 0(2) -> Core 0
[ 0.080000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 0.080000] Compat vDSO mapped to ffffe000.
[ 0.080000] Checking 'hlt' instruction... OK.
[ 0.096000] SMP alternatives: switching to UP code
[ 0.096000] Early unpacking initramfs... done
[ 0.456000] ACPI: Core revision 20070126
[ 0.456000] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 0.460000] CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02
[ 0.460000] SMP alternatives: switching to SMP code
[ 0.460000] Booting processor 1/1 eip 3000
[ 0.472000] Initializing CPU#1
[ 0.552000] Calibrating delay using timer specific routine.. 3214.65 BogoMIPS (lpj=6429301)
[ 0.552000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 0.552000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.552000] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.552000] CPU 1(2) -> Core 1
[ 0.552000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 0.552000] CPU1: AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02
[ 0.552000] Total of 2 processors activated (6432.12 BogoMIPS).
[ 0.552000] ENABLING IO-APIC IRQs
[ 0.552000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.596000] Brought up 2 CPUs
[ 0.612000] migration_cost=4000
[ 0.612000] Booting paravirtualized kernel on bare hardware
[ 0.612000] Time: 14:07:17 Date: 10/12/107
[ 0.612000] NET: Registered protocol family 16
[ 0.612000] EISA bus registered
[ 0.612000] ACPI: bus type pci registered
[ 0.624000] PCI: BIOS BUG #81[49435000] found
[ 0.624000] PCI: Using configuration type 1
[ 0.624000] Setting up standard PCI resources
[ 0.624000] ACPI: EC: Look up EC in DSDT
[ 0.624000] ACPI: EC: GPE=0x01, ports=0x66, 0x62
[ 0.628000] ACPI: System BIOS is requesting _OSI(Linux)
[ 0.628000] ACPI: Please test with "acpi_osi=!Linux"
[ 0.628000] Please send dmidecode to linux-acpi@xxxxxxxxxxxxxxx
[ 0.628000] ACPI: Interpreter enabled
[ 0.628000] ACPI: (supports S0 S3 S4 S5)
[ 0.628000] ACPI: Using IOAPIC for interrupt routing
[ 0.640000] ACPI: EC: GPE=0x01, ports=0x66, 0x62
[ 0.640000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.640000] PCI: Probing PCI hardware (bus 00)
[ 0.640000] PCI: Transparent bridge - 0000:00:10.0
[ 0.640000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.640000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[ 0.640000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
[ 0.640000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
[ 0.640000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
[ 0.676000] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.676000] ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19 20 21 22 23) *10
[ 0.676000] ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19 20 21 22 23) *10
[ 0.676000] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 *11 14 15)
[ 0.676000] ACPI: PCI Interrupt Link [LK1E] (IRQs 16 17 18 19 20 21 22 23) *10
[ 0.680000] ACPI: PCI Interrupt Link [LK2E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.680000] ACPI: PCI Interrupt Link [LK3E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.680000] ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.680000] ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20 21 22 23) *10
[ 0.680000] ACPI: PCI Interrupt Link [LSMU] (IRQs 16 17 18 19 20 21 22 23) *11
[ 0.680000] ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20 21 22 23) *11
[ 0.680000] ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20 21 22 23) *7
[ 0.680000] ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20 21 22 23) *11
[ 0.680000] ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.680000] ACPI: PCI Interrupt Link [LACI] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.680000] ACPI: PCI Interrupt Link [LMCI] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.680000] ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 0.680000] ACPI: PCI Interrupt Link [LTID] (IRQs 16 17 18 19 20 21 22 23) *5
[ 0.680000] ACPI: PCI Interrupt Link [LSI1] (IRQs 16 17 18 19 20 21 22 23) *0
[ 0.680000] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.680000] pnp: PnP ACPI init
[ 0.680000] ACPI: bus type pnp registered
[ 0.684000] pnp: PnP ACPI: found 11 devices
[ 0.684000] ACPI: ACPI bus type pnp unregistered
[ 0.684000] PnPBIOS: Disabled by ACPI PNP
[ 0.684000] PCI: Using ACPI for IRQ routing
[ 0.684000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.684000] PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
[ 0.684000] PCI: Cannot allocate resource region 5 of device 0000:03:00.0
[ 0.684000] NET: Registered protocol family 8
[ 0.684000] NET: Registered protocol family 20
[ 0.684000] pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.684000] pnp: 00:02: ioport range 0x1000-0x107f has been reserved
[ 0.684000] pnp: 00:02: ioport range 0x1080-0x10ff has been reserved
[ 0.684000] pnp: 00:02: ioport range 0x1400-0x147f has been reserved
[ 0.684000] pnp: 00:02: ioport range 0x1480-0x14ff has been reserved
[ 0.684000] pnp: 00:02: ioport range 0x1800-0x187f has been reserved
[ 0.684000] pnp: 00:02: ioport range 0x1880-0x18ff has been reserved
[ 0.684000] pnp: 00:02: ioport range 0x2000-0x203f has been reserved
[ 0.688000] Time: hpet clocksource has been installed.
[ 0.716000] PCI: Bridge: 0000:00:02.0
[ 0.716000] IO window: disabled.
[ 0.716000] MEM window: disabled.
[ 0.716000] PREFETCH window: disabled.
[ 0.716000] PCI: Bridge: 0000:00:03.0
[ 0.716000] IO window: 4000-4fff
[ 0.716000] MEM window: c4000000-c40fffff
[ 0.716000] PREFETCH window: disabled.
[ 0.716000] PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:03:00.0
[ 0.716000] PCI: Bridge: 0000:00:04.0
[ 0.716000] IO window: 5000-5fff
[ 0.716000] MEM window: c1000000-c2ffffff
[ 0.716000] PREFETCH window: d0000000-dfffffff
[ 0.716000] PCI: Bus 5, cardbus bridge: 0000:04:06.0
[ 0.716000] IO window: 00006000-000060ff
[ 0.716000] IO window: 00006400-000064ff
[ 0.716000] PREFETCH window: 50000000-53ffffff
[ 0.716000] MEM window: 54000000-57ffffff
[ 0.716000] PCI: Bridge: 0000:00:10.0
[ 0.716000] IO window: 6000-6fff
[ 0.716000] MEM window: c3000000-c30fffff
[ 0.716000] PREFETCH window: 50000000-53ffffff
[ 0.716000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 0.716000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 0.716000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 0.716000] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 0.716000] ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 11
[ 0.716000] ACPI: PCI Interrupt 0000:04:06.0[A] -> Link [LNK4] -> GSI 11 (level, low) -> IRQ 11
[ 0.716000] NET: Registered protocol family 2
[ 0.760000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.760000] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 0.760000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.760000] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.760000] TCP reno registered
[ 0.776000] checking if image is initramfs... it is
[ 1.484000] Freeing initrd memory: 7063k freed
[ 1.484000] Simple Boot Flag at 0x36 set to 0x1
[ 1.484000] audit: initializing netlink socket (disabled)
[ 1.484000] audit(1194876437.188:1): initialized
[ 1.484000] highmem bounce pool size: 64 pages
[ 1.488000] VFS: Disk quotas dquot_6.5.1
[ 1.488000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.488000] io scheduler noop registered
[ 1.488000] io scheduler anticipatory registered
[ 1.488000] io scheduler deadline registered
[ 1.488000] io scheduler cfq registered (default)
[ 1.508000] Boot video device is 0000:03:00.0
[ 1.508000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 1.508000] assign_interrupt_mode Found MSI capability
[ 1.508000] Allocate Port Service[0000:00:02.0:pcie00]
[ 1.508000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 1.508000] assign_interrupt_mode Found MSI capability
[ 1.508000] Allocate Port Service[0000:00:03.0:pcie00]
[ 1.508000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 1.508000] assign_interrupt_mode Found MSI capability
[ 1.508000] Allocate Port Service[0000:00:04.0:pcie00]
[ 1.508000] isapnp: Scanning for PnP cards...
[ 1.860000] isapnp: No Plug & Play device found
[ 1.888000] Real Time Clock Driver v1.12ac
[ 1.888000] hpet_resources: 0xfed00000 is busy
[ 1.888000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.888000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1.888000] input: Macintosh mouse button emulation as /class/input/input0
[ 1.888000] PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.888000] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.888000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.888000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.888000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.888000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.888000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.888000] mice: PS/2 mouse device common for all mice
[ 1.888000] EISA: Probing bus 0 at eisa.0
[ 1.888000] Cannot allocate resource for EISA slot 1
[ 1.888000] Cannot allocate resource for EISA slot 2
[ 1.888000] Cannot allocate resource for EISA slot 3
[ 1.888000] Cannot allocate resource for EISA slot 4
[ 1.888000] Cannot allocate resource for EISA slot 5
[ 1.888000] Cannot allocate resource for EISA slot 6
[ 1.888000] EISA: Detected 0 cards.
[ 1.888000] TCP cubic registered
[ 1.888000] NET: Registered protocol family 1
[ 1.888000] Using IPI No-Shortcut mode
[ 1.888000] Magic number: 15:480:131
[ 1.888000] hash matches device device:06
[ 1.888000] Freeing unused kernel memory: 364k freed
[ 1.896000] input: AT Translated Set 2 keyboard as /class/input/input1
[ 3.152000] AppArmor: AppArmor initialized<5>audit(1194876439.188:2): type=1505 info="AppArmor initialized" pid=1251
[ 3.160000] fuse init (API version 7.8)
[ 3.168000] Failure registering capabilities with primary security module.
[ 3.200000] ACPI: Thermal Zone [TZS0] (52 C)
[ 3.204000] ACPI: Thermal Zone [TZS1] (55 C)
[ 3.872000] usbcore: registered new interface driver usbfs
[ 3.872000] usbcore: registered new interface driver hub
[ 3.872000] usbcore: registered new device driver usb
[ 3.872000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.872000] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 23
[ 3.872000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUS0] -> GSI 23 (level, high) -> IRQ 16
[ 3.872000] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 3.872000] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 3.872000] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
[ 3.872000] ohci_hcd 0000:00:0b.0: irq 16, io mem 0xc0004000
[ 3.888000] SCSI subsystem initialized
[ 3.896000] libata version 2.21 loaded.
[ 3.936000] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 3.944000] usb usb1: configuration #1 chosen from 1 choice
[ 3.944000] hub 1-0:1.0: USB hub found
[ 3.944000] hub 1-0:1.0: 8 ports detected
[ 4.008000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 4.008000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 4.052000] sata_nv 0000:00:0e.0: version 3.4
[ 4.052000] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 22
[ 4.052000] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LTID] -> GSI 22 (level, high) -> IRQ 17
[ 4.052000] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 4.052000] scsi0 : sata_nv
[ 4.056000] scsi1 : sata_nv
[ 4.056000] ata1: SATA max UDMA/133 cmd 0x000130b0 ctl 0x000130a6 bmdma 0x00013090 irq 17
[ 4.056000] ata2: SATA max UDMA/133 cmd 0x000130a8 ctl 0x000130a2 bmdma 0x00013098 irq 17
[ 4.356000] usb 1-6: new full speed USB device using ohci_hcd and address 2
[ 4.532000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.540000] ata1.00: ATA-7: Hitachi HTS541616J9SA00, SB4OC70P, max UDMA/100
[ 4.540000] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 4.564000] ata1.00: configured for UDMA/100
[ 4.724000] usb 1-6: configuration #1 chosen from 1 choice
[ 4.876000] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.880000] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54161 SB4O PQ: 0 ANSI: 5
[ 4.884000] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 21
[ 4.884000] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 21 (level, high) -> IRQ 18
[ 4.884000] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 4.884000] forcedeth: using HIGHDMA
[ 5.056000] usb 1-8: new full speed USB device using ohci_hcd and address 3
[ 5.272000] usb 1-8: configuration #1 chosen from 1 choice
[ 5.300000] usbcore: registered new interface driver libusual
[ 5.304000] Initializing USB Mass Storage driver...
[ 5.304000] scsi2 : SCSI emulation for USB Mass Storage devices
[ 5.304000] usb-storage: device found at 3
[ 5.304000] usb-storage: waiting for device to settle before scanning
[ 5.304000] usbcore: registered new interface driver usb-storage
[ 5.304000] USB Mass Storage support registered.
[ 5.404000] eth0: forcedeth.c: subsystem: 01025:0112 bound to 0000:00:14.0
[ 5.404000] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
[ 5.404000] NFORCE-MCP51: chipset revision 241
[ 5.404000] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 5.404000] NFORCE-MCP51: BIOS didn't set cable bits correctly. Enabling workaround.
[ 5.404000] NFORCE-MCP51: 0000:00:0d.0 (rev f1) UDMA133 controller
[ 5.404000] ide0: BM-DMA at 0x3080-0x3087, BIOS settings: hda:pio, hdb:pio
[ 5.404000] ide1: BM-DMA at 0x3088-0x308f, BIOS settings: hdc:DMA, hdd:pio
[ 5.404000] Probing IDE interface ide0...
[ 5.416000] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 5.416000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.416000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.416000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.416000] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 5.416000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.416000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.416000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.416000] sda: sda1 sda2 sda3 < sda5 sda6 >
[ 5.488000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.492000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.788000] Attempting manual resume
[ 5.788000] swsusp: Resume From Partition 8:5
[ 5.788000] PM: Checking swsusp image.
[ 5.792000] PM: Resume from disk failed.
[ 5.828000] kjournald starting. Commit interval 5 seconds
[ 5.828000] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.972000] Probing IDE interface ide1...
[ 6.708000] hdc: Slimtype DVDRW SSM-8515S, ATAPI CD/DVD-ROM drive
[ 7.380000] ide1 at 0x170-0x177,0x376 on irq 15
[ 7.408000] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 20
[ 7.408000] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUS2] -> GSI 20 (level, high) -> IRQ 19
[ 7.408000] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[ 7.408000] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 7.408000] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[ 7.408000] ehci_hcd 0000:00:0b.1: debug port 1
[ 7.408000] PCI: cache line size of 64 is not supported by device 0000:00:0b.1
[ 7.412000] ehci_hcd 0000:00:0b.1: irq 19, io mem 0xc0005000
[ 7.412000] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 7.412000] usb 1-6: USB disconnect, address 2
[ 7.412000] usb usb2: configuration #1 chosen from 1 choice
[ 7.412000] hub 2-0:1.0: USB hub found
[ 7.412000] hub 2-0:1.0: 8 ports detected
[ 7.548000] usb 1-8: USB disconnect, address 3
[ 7.936000] usb 2-6: new high speed USB device using ehci_hcd and address 2
[ 8.320000] usb 2-6: configuration #1 chosen from 1 choice
[ 8.576000] usb 2-8: new high speed USB device using ehci_hcd and address 3
[ 8.712000] usb 2-8: configuration #1 chosen from 1 choice
[ 8.712000] scsi3 : SCSI emulation for USB Mass Storage devices
[ 8.712000] usb-storage: device found at 3
[ 8.712000] usb-storage: waiting for device to settle before scanning
[ 13.712000] usb-storage: device scan complete
[ 13.712000] scsi 3:0:0:0: Direct-Access HP Photosmart C4180 1.00 PQ: 0 ANSI: 2
[ 13.724000] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 13.724000] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 14.556000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 14.556000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.732000] ath_hal: module license 'Proprietary' taints kernel.
[ 14.732000] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[ 14.872000] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
[ 14.872000] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
[ 15.048000] wlan: 0.8.4.2 (0.9.3.2)
[ 15.104000] Yenta: CardBus bridge found at 0000:04:06.0 [1025:0112]
[ 15.104000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 15.104000] Yenta: Routing CardBus interrupts to PCI
[ 15.104000] Yenta TI: socket 0000:04:06.0, mfunc 0x013a1b22, devctl 0x64
[ 15.124000] Linux agpgart interface v0.102 (c) Dave Jones
[ 15.200000] ath_pci: 0.9.4.5 (0.9.3.2)
[ 15.348000] Yenta: ISA IRQ mask 0x04f8, PCI irq 11
[ 15.348000] Socket status: 30000006
[ 15.348000] Yenta: Raising subordinate bus# of parent bus (#04) from #05 to #08
[ 15.348000] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 15.348000] cs: IO port probe 0x6000-0x6fff: clean.
[ 15.348000] pcmcia: parent PCI bridge Memory window: 0xc3000000 - 0xc30fffff
[ 15.348000] pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
[ 15.348000] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 19
[ 15.348000] ACPI: PCI Interrupt 0000:04:05.0[A] -> Link [LNK2] -> GSI 19 (level, high) -> IRQ 20
[ 15.656000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1280b1, caps: 0xa04713/0x204000
[ 15.688000] input: SynPS/2 Synaptics TouchPad as /class/input/input2
[ 16.068000] input: PC Speaker as /class/input/input3
[ 16.348000] Linux video capture interface: v2.00
[ 16.424000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 1 alt 0 proto 2 vid 0x03F0 pid 0x5711
[ 16.424000] usbcore: registered new interface driver usblp
[ 16.424000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 16.436000] ath_rate_sample: 1.2 (0.9.3.2)
[ 16.468000] uvcvideo: Found UVC 1.00 device USB2.0 Camera (5986:0100)
[ 16.468000] hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 16.468000] Uniform CD-ROM driver Revision: 3.20
[ 16.524000] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[ 16.524000] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 16.524000] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[ 16.524000] wifi0: mac 7.8 phy 4.5 radio 5.6
[ 16.524000] wifi0: Use hw queue 1 for WME_AC_BE traffic
[ 16.524000] wifi0: Use hw queue 0 for WME_AC_BK traffic
[ 16.524000] wifi0: Use hw queue 2 for WME_AC_VI traffic
[ 16.524000] wifi0: Use hw queue 3 for WME_AC_VO traffic
[ 16.524000] wifi0: Use hw queue 8 for CAB traffic
[ 16.524000] wifi0: Use hw queue 9 for beacons
[ 16.548000] usbcore: registered new interface driver uvcvideo
[ 16.548000] USB Video Class driver (v0.1.0)
[ 16.556000] wifi0: Atheros 5212: mem=0xc3000000, irq=20
[ 16.556000] ACPI: PCI Interrupt 0000:04:06.2[A] -> Link [LNK4] -> GSI 11 (level, low) -> IRQ 11
[ 16.556000] ACPI: PCI Interrupt Link [LK1E] enabled at IRQ 18
[ 16.556000] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LK1E] -> GSI 18 (level, high) -> IRQ 21
[ 16.556000] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 16.556000] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep 12 14:12:24 PDT 2007
[ 16.780000] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 17
[ 16.780000] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 17 (level, high) -> IRQ 22
[ 16.780000] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 16.876000] cs: IO port probe 0x100-0x3af: clean.
[ 16.880000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 16.880000] cs: IO port probe 0x820-0x8ff: clean.
[ 16.880000] cs: IO port probe 0xc00-0xcf7: clean.
[ 16.880000] cs: IO port probe 0xa00-0xaff: clean.
[ 17.520000] loop: module loaded
[ 17.560000] lp: driver loaded but no devices found
[ 17.660000] Adding 2931820k swap on /dev/sda5. Priority:-1 extents:1 across:2931820k
[ 18.132000] EXT3 FS on sda6, internal journal
[ 18.588000] hda_intel: azx_get_response timeout, switching to polling mode...
[ 19.504000] No dock devices found.
[ 19.520000] ACPI: AC Adapter [ADP1] (off-line)
[ 19.632000] input: Power Button (FF) as /class/input/input4
[ 19.632000] ACPI: Power Button (FF) [PWRF]
[ 19.632000] input: Lid Switch as /class/input/input5
[ 19.632000] ACPI: Lid Switch [LID0]
[ 19.632000] input: Sleep Button (CM) as /class/input/input6
[ 19.632000] ACPI: Sleep Button (CM) [SLPB]
[ 19.632000] input: Power Button (CM) as /class/input/input7
[ 19.632000] ACPI: Power Button (CM) [PWRB]
[ 19.824000] ACPI: Battery Slot [BAT0] (battery present)
[ 19.860000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 19.860000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 20.108000] powernow-k8: Found 2 AMD Turion(tm) 64 X2 Mobile Technology TL-52 processors (version 2.00.00)
[ 20.108000] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x13
[ 20.108000] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x1e
[ 21.200000] ppdev: user-space parallel port driver
[ 21.460000] audit(1194876457.569:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5097 profile="/usr/sbin/cupsd"
[ 21.492000] apm: BIOS not found.
[ 21.876000] eth0: no link during initialization.
[ 22.200000] Failure registering capabilities with primary security module.
[ 23.000000] Clocksource tsc unstable (delta = -250036454 ns)
[ 23.016000] Bluetooth: Core ver 2.11
[ 23.016000] NET: Registered protocol family 31
[ 23.016000] Bluetooth: HCI device and connection manager initialized
[ 23.016000] Bluetooth: HCI socket layer initialized
[ 23.060000] Bluetooth: L2CAP ver 2.8
[ 23.060000] Bluetooth: L2CAP socket layer initialized
[ 23.176000] Bluetooth: RFCOMM socket layer initialized
[ 23.176000] Bluetooth: RFCOMM TTY layer initialized
[ 23.176000] Bluetooth: RFCOMM ver 1.8
[ 68.244000] NET: Registered protocol family 17
[ 77.656000] NET: Registered protocol family 10
[ 77.656000] lo: Disabled Privacy Extensions
[ 77.656000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 88.372000] ath0: no IPv6 routers present
# dmidecode 2.9
SMBIOS 2.4 present.
27 structures occupying 947 bytes.
Table at 0x3FF6B000.
Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
Vendor: Phoenix Technologies LTD
Version: V1.19
Release Date: 05/15/2007
Address: 0xE5C60
Runtime Size: 107424 bytes
ROM Size: 1024 kB
Characteristics:
ISA is supported
PCI is supported
PC Card (PCMCIA) is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
ACPI is supported
USB legacy is supported
AGP is supported
BIOS boot specification is supported
Targeted content distribution is supported
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: Acer
Product Name: TravelMate 7510
Version: 0100
Serial Number: LXTJW0X00171001A6E2000
UUID: 939548E0-CC09-11DB-8865-A7743EFADFDD
Wake-up Type: Power Switch
SKU Number: Not Specified
Family: Not Specified
Handle 0x0002, DMI type 2, 8 bytes
Base Board Information
Manufacturer: Acer
Product Name: Myallm
Version: Rev
Serial Number: LXTJW0X00171001A6E2000
Handle 0x0003, DMI type 3, 17 bytes
Chassis Information
Manufacturer: Acer
Type: Notebook
Lock: Not Present
Version: N/A
Serial Number: None
Asset Tag: None
Boot-up State: Safe
Power Supply State: Safe
Thermal State: Safe
Security Status: None
OEM Information: 0x00001234
Handle 0x0004, DMI type 4, 35 bytes
Processor Information
Socket Designation: U1
Type: Central Processor
Family: Athlon XP
Manufacturer: AMD
ID: 82 0F 04 00 FF FB 8B 17
Signature: Family 15, Model 72, Stepping 2
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
MMX (MMX technology supported)
FXSR (Fast floating-point save and restore)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
HTT (Hyper-threading technology)
Version: AMD Turion(tm) 64
Voltage: 3.3 V
External Clock: 800 MHz
Max Speed: 500 MHz
Current Speed: 1600 MHz
Status: Populated, Enabled
Upgrade: Socket 754
L1 Cache Handle: 0x0005
L2 Cache Handle: 0x0006
L3 Cache Handle: Not Provided
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x0005, DMI type 7, 19 bytes
Cache Information
Socket Designation: L1 Cache
Configuration: Enabled, Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 16 KB
Maximum Size: 16 KB
Supported SRAM Types:
Burst
Pipeline Burst
Asynchronous
Installed SRAM Type: Asynchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x0006, DMI type 7, 19 bytes
Cache Information
Socket Designation: L2 Cache
Configuration: Enabled, Socketed, Level 2
Operational Mode: Write Back
Location: External
Installed Size: 1024 KB
Maximum Size: 2048 KB
Supported SRAM Types:
Burst
Pipeline Burst
Asynchronous
Installed SRAM Type: Synchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x0007, DMI type 9, 13 bytes
System Slot Information
Designation: PCMCIA Slot CBUS1
Type: 32-bit PC Card (PCMCIA)
Current Usage: Available
Length: Long
ID: Adapter 0, Socket 0
Characteristics:
5.0 V is provided
3.3 V is provided
PC Card-16 is supported
Cardbus is supported
Handle 0x0008, DMI type 10, 6 bytes
On Board Device Information
Type: Sound
Status: Disabled
Description: HD-Audio
Handle 0x0009, DMI type 11, 5 bytes
OEM Strings
String 1: Nvidia
Handle 0x000A, DMI type 15, 29 bytes
System Event Log
Area Length: 0 bytes
Header Start Offset: 0x0000
Data Start Offset: 0x0000
Access Method: General-purpose non-volatile data functions
Access Address: 0x0000
Status: Invalid, Not Full
Change Token: 0x00000000
Header Format: No Header
Supported Log Type Descriptors: 3
Descriptor 1: POST error
Data Format 1: POST results bitmap
Descriptor 2: Single-bit ECC memory error
Data Format 2: Multiple-event
Descriptor 3: Multi-bit ECC memory error
Data Format 3: Multiple-event
Handle 0x000B, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 4 GB
Error Information Handle: Not Provided
Number Of Devices: 2
Handle 0x000C, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x000B
Error Information Handle: No Error
Total Width: 32 bits
Data Width: 32 bits
Size: 1024 MB
Form Factor: SODIMM
Set: 1
Locator: M1
Bank Locator: Bank 0
Type: DDR2
Type Detail: Synchronous
Speed: Unknown
Manufacturer: Not Specified
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x000D, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x000B
Error Information Handle: No Error
Total Width: Unknown
Data Width: Unknown
Size: No Module Installed
Form Factor: SODIMM
Set: 1
Locator: M2
Bank Locator: Bank 1
Type: DDR2
Type Detail: Unknown
Speed: Unknown
Manufacturer: Not Specified
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x000E, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0003FFFFFFF
Range Size: 1 GB
Physical Array Handle: 0x000B
Partition Width: 0
Handle 0x000F, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0003FFFFFFF
Range Size: 1 GB
Physical Device Handle: 0x000C
Memory Array Mapped Address Handle: 0x000E
Partition Row Position: 1
Handle 0x0010, DMI type 23, 13 bytes
System Reset
Status: Enabled
Watchdog Timer: Present
Boot Option: Do Not Reboot
Boot Option On Limit: Do Not Reboot
Reset Count: Unknown
Reset Limit: Unknown
Timer Interval: Unknown
Timeout: Unknown
Handle 0x0011, DMI type 24, 5 bytes
Hardware Security
Power-On Password Status: Disabled
Keyboard Password Status: Unknown
Administrator Password Status: Disabled
Front Panel Reset Status: Unknown
Handle 0x0012, DMI type 25, 9 bytes
System Power Controls
Next Scheduled Power-on: 12-31 23:59:59
Handle 0x0013, DMI type 26, 20 bytes
Voltage Probe
Description: Voltage Probe
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value: Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Handle 0x0014, DMI type 27, 12 bytes
Cooling Device
Temperature Probe Handle: 0x0015
Type: Fan
Status: OK
OEM-specific Information: 0x00000000
Handle 0x0015, DMI type 28, 20 bytes
Temperature Probe
Description: Temperature Probe
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Handle 0x0016, DMI type 29, 20 bytes
Electrical Current Probe
Description: Electrical Current Probe
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value: Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Handle 0x0017, DMI type 30, 6 bytes
Out-of-band Remote Access
Manufacturer Name: Intel
Inbound Connection: Enabled
Outbound Connection: Disabled
Handle 0x0018, DMI type 32, 20 bytes
System Boot Information
Status: <OUT OF SPEC>
Handle 0x0019, DMI type 150, 14 bytes
OEM-specific Type
Header and Data:
96 0E 19 00 01 01 00 00 00 00 00 00 00 00
Strings:
ABSOLUTE(PHOENIX) CLM
Handle 0x001A, DMI type 127, 4 bytes
End Of Table
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 1: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 800MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR-
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [44] #00 [00fe]
Capabilities: [fc] #00 [0000]
00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:02.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <512ns, L1 <4us
Link: ASPM L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn+ PwrFlt+ MRL- PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: c4000000-c40fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <512ns, L1 <4us
Link: ASPM L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn+ PwrFlt+ MRL- PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:04.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: c1000000-c2ffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <512ns, L1 <4us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=9 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 3040 [size=64]
Region 5: I/O ports at 3000 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.3 Co-processor: nVidia Corporation MCP51 PMU (rev a3)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at c0040000 (32-bit, non-prefetchable) [size=256K]
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c0004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 19
Region 0: Memory at c0005000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev f1) (prog-if 8a [Master SecP PriP])
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at 3080 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev f1) (prog-if 85 [Master SecO PriO])
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 30b0 [size=8]
Region 1: I/O ports at 30a4 [size=4]
Region 2: I/O ports at 30a8 [size=8]
Region 3: I/O ports at 30a0 [size=4]
Region 4: I/O ports at 3090 [size=16]
Region 5: Memory at c0006000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=08, sec-latency=64
I/O behind bridge: 00006000-00006fff
Memory behind bridge: c3000000-c30fffff
Prefetchable memory behind bridge: 50000000-53ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [b8] Subsystem: Gammagraphx, Inc. Unknown device 0000
Capabilities: [8c] HyperTransport: MSI Mapping
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping
00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at c0007000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 30b8 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=8
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]
03:00.0 VGA compatible controller: nVidia Corporation G70 [GeForce Go 7600] (rev a1) (prog-if 00 [VGA])
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at c2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at c1000000 (64-bit, non-prefetchable) [size=16M]
Region 5: I/O ports at 5000 [size=128]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <1us, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <1us, L1 <4us
Link: ASPM L0s L1 Enabled RCB 128 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
04:05.0 Ethernet controller: Atheros Communications, Inc. AR2413 802.11bg NIC (rev 01)
Subsystem: AMBIT Microsystem Corp. Unknown device 0418
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at c3000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
04:06.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c3010000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=04, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 50000000-53fff000 (prefetchable)
Memory window 1: 54000000-57fff000
I/O window 0: 00006000-000060ff
I/O window 1: 00006400-000064ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
04:06.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD)
Subsystem: Acer Incorporated [ALI] Unknown device 0112
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c3012000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
