I'm trying to upgrade a cluster from Mandrake 10.1 (with 2.6.8.1
vanilla kernel) to Mandriva 2007 (2.6.17-8mdv kernel). These machines
have Tyan S2466N-4M motherboards, single AMD Athlon MP 2200+ processors,
and the latest (and no doubt last) BIOS = 4.06. ACPI is enabled in
the BIOS.
One test node was upgraded and worked correctly except for one
annoying problem: afterwards that node would
no longer respond to the front power button following a
"poweroff". To reboot that system it is now necessary to pull
the power cord, count to 20, plug it back in again, and then push
the power button.
There were a variety of changes to the acpi between those kernels
versions, but the one that I think maybe indicates the problem
is the new
/proc/acpi/wakeup
file, which on the problem machine contains only:
Device Sleep state Status
PCIO 5 disabled
OP2P 5 disabled
USB0 1 disabled
So I tried: echo "OP2P" > /proc/acpi/wakeup
which strangely enabled both of the first two
entries, neither of which was "* enabled", just "enabled". This
was not enough to make the power button work following
a "poweroff".
Those 3 wakeup devices were all that was listed in /var/log/dmesg,
so it isn't that the OS dropped the power button after the BIOS
reported its presence, it seems that the BIOS never told the OS
that the power button exists. (How this worked with the older
OS I have no idea). Sleep states listed in /var/log/dmesg are:
ACPI: (supports S0 S1 S4 S5)
Here are all the ACPI lines in /var/log/dmesg:
BIOS-e820: 000000003fef0000 - 000000003feff000 (ACPI data)
BIOS-e820: 000000003feff000 - 000000003ff00000 (ACPI NVS)
ACPI: RSDP (v000 PTLTD ) @ 0x000f7100
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x3fefcf36
ACPI: FADT (v001 AMD TECATE 0x06040000 PTL 0x000f4240) @ 0x3fefef3c
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @
0x3fefefb0
ACPI: DSDT (v001 AMD AMDACPI 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
ACPI: bus type pci registered
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11)
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PCI: Using ACPI for IRQ routing
apm: overridden by ACPI.
ACPI wakeup devices:
ACPI: (supports S0 S1 S4 S5)
On other systems (different motherboards and processors) with
recent kernels this /proc/acpi/wakeup contains either
PWRB 3 * enabled (Mandriva 2006)
or
SLPB 4 * enabled (Mandriva 2007)
and those machines do boot from a power button push following
"poweroff".
Boot parameters for both the working and nonworking Mandriva 2007
machines were the same (other than different partition numbers):
image=/boot/vmlinuz
label="linux"
root=/dev/hda5
initrd=/boot/initrd.img
append="resume=/dev/hda2"
The ACPI entries in config are:
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
CONFIG_ACPI_HOTKEY=m
CONFIG_ACPI_FAN=m
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=m
CONFIG_ACPI_ASUS=m
CONFIG_ACPI_IBM=m
CONFIG_ACPI_IBM_DOCK=y
CONFIG_ACPI_TOSHIBA=m
CONFIG_ACPI_CUSTOM_DSDT_INITRD=y
CONFIG_ACPI_BLACKLIST_YEAR=0
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_ACPI_CONTAINER=m
What steps do I have to take to get a power button
device into /proc/acpi/wakeup???
Any idea why the older kernel's ACPI variant was happy start up
from the front panel power switch following "poweroff", but the
newer one isn't? (There were no specific acpi kernel switches).
Thank you,
David Mathog
mathog@xxxxxxxxxxx
Manager, Sequence Analysis Facility, Biology Division, Caltech
-
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
