Re: 2.6.18-rc1-mm1

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 10/07/2006 12:56 a.m., Alan Cox wrote:
Ar Sul, 2006-07-09 am 05:22 -0700, ysgrifennodd Andrew Morton:
ata5: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x30B0 irq 14
scsi4 : ata_piix
ata5.00: ATAPI, max UDMA/66
ata5.00: configured for UDMA/66

More ATAPI devices getting uppity about mode setting.

John stuff.  I suspect it's natural and normal, if the IDE error handling
did something rude with interrupt holdoff.

The new libata should be more polite than that, although since the ATA
drive can stall the CPU indefinitely you lose anyway 8(

It may not be related to ATA. I just reloaded into 2.6.17-mm6 to get the info for Alan and saw it when booting up on that too:

PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
Losing some ticks... checking if CPU frequency changed.
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7

Note it was in a different place in here than in -rc1-mm1 (slightly later in the bootup).

I'm fairly sure it's not new to this release.

Jul 2 12:03:28 tornado kernel: hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66)

Can you send me the full hdparm identify stuff for this ?

sh-3.1# hdparm -I /dev/hda

/dev/hda:

ATAPI CD-ROM, with removable media
        Model Number:       PIONEER DVD-RW  DVR-111D
        Serial Number:      FADC005671WL
        Firmware Revision:  1.23
Standards:
        Likely used CD-ROM ATAPI-1
Configuration:
        DRQ response: 50us.
        Packet size: 12 bytes
Capabilities:
        LBA, IORDY(can be disabled)
        Buffer size: 64.0kB
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    Power Management feature set
           *    PACKET command feature set
           *    DEVICE_RESET command
HW reset results:
        CBLID- above Vih
        Device num = 0 determined by the jumper
sh-3.1#
sh-3.1# hdparm -i /dev/hda

/dev/hda:

 Model=PIONEER DVD-RW DVR-111D, FwRev=1.23, SerialNo=
 Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
 RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
 BuffType=13395, BuffSize=64kB, MaxMultSect=0
 (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 *udma4
 AdvancedPM=no
 Drive conforms to: Unspecified:  ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5

 * signifies the current active mode

sh-3.1#


Reuben
-
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux IBM ACPI]     [Linux Power Management]     [Linux Kernel]     [Linux Laptop]     [Kernel Newbies]     [Share Photos]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux