If anyone can shed any light on my current problem, I would greatly
appreciate it.
I have been working to install an Agere Systems Lucent V.92 Data/Fax Modem
in Ubuntu Natty.
I downloaded agrsm06pci-2.1.80~20100106.tar.gz and installed it on my
machine.
I can execute:
sudo modprobe agrmodem
sudo modprobe agrserial
and both commands complete successfully. It appears from the ModemData.txt
pasted below, and which was run after these commands were executed, that the
drivers have loaded.
I see /dev/ttyAGS3 is created and have linked it successfully using ln ?s
/dev/ttyAGS3 /dev/modem
However, whenever I access /dev/modem the entire machine hangs and I have to
reboot.
Some additional information that may be helpful:
1. I have pasted the contents dmesg.txt below. It seems to suggest some
addressing conflicts, but I do not understand how to resolve them.
2. sudo lspci -s 02:02.0 ?nv gives the following output, suggesting that
perhaps the modem is disabled?
02:02.0 0780: 11c1:0620
Subsystem: 11c1:0620
Flags: medium devsel
I/O ports at <unassigned> [disabled]
Capabilities: [f8] Power Management version 3
3. cat /proc/interrupts gives the following output:
CPU0
0: 44 IO-APIC-edge timer
1: 8 IO-APIC-edge i8042
4: 4 IO-APIC-edge
6: 3 IO-APIC-edge floppy
7: 0 IO-APIC-edge parport0
8: 0 IO-APIC-edge rtc0
9: 0 IO-APIC-fasteoi acpi
14: 84183 IO-APIC-edge ata_piix
15: 111 IO-APIC-edge ata_piix
16: 3 IO-APIC-fasteoi uhci_hcd:usb2, nouveau
18: 0 IO-APIC-fasteoi uhci_hcd:usb4
19: 0 IO-APIC-fasteoi uhci_hcd:usb3
20: 19443 IO-APIC-fasteoi eth1
21: 35 IO-APIC-fasteoi firewire_ohci
22: 0 IO-APIC-fasteoi EMU10K1
23: 0 IO-APIC-fasteoi ehci_hcd:usb1
NMI: 0 Non-maskable interrupts
LOC: 194953 Local timer interrupts
SPU: 0 Spurious interrupts
PMI: 0 Performance monitoring interrupts
IWI: 0 IRQ work interrupts
RES: 0 Rescheduling interrupts
CAL: 0 Function call interrupts
TLB: 0 TLB shootdowns
TRM: 0 Thermal event interrupts
THR: 0 Threshold APIC interrupts
MCE: 0 Machine check exceptions
MCP: 8 Machine check polls
ERR: 0
MIS: 0
Contents of ModemData.txt follows:
-------------------------- System information ----------------------------
CPU=i686, Ubuntu , ALSA_version=1.0.23
Linux version 2.6.38-16-generic (buildd@panlong) (gcc version 4.5.2
(Ubuntu/Linaro 4.5.2-8ubuntu4) ) #67-Ubuntu SMP Thu Sep 6 18:00:43 UTC 2012
scanModem update of: 2011_08_08
Distrib_ID=Ubuntu
DistribCodeName=natty
AptRepositoryStem=http://us.archive.ubuntu.com/ubuntu/
The dkms driver upgrade utilities are installed,
There are no blacklisted modem drivers in /etc/modprobe* files
Potentially useful modem drivers now loaded are:
agrmodem agrserial
If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@xxxxxxxxxxxxx
Candidate PCI devices with modem chips are:
02:02.0 Communication controller: Agere Systems Lucent V.92 Data/Fax Modem
High Definition Audio cards can host modem chips.
For candidate card in slot 02:02.0, firmware information and bootup
diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
02:02.0 11c1:0620 11c1:0620 Communication controller:
Agere Systems Lucent V.92 Data/Fax Modem
Modem interrupt assignment and sharing:
18: 0 IO-APIC-fasteoi uhci_hcd:usb4
--- Bootup diagnostics for card in PCI slot 02:02.0 ----
[ 0.084446] pci 0000:02:02.0: [11c1:0620] type 0 class 0x000780
[ 0.084467] pci 0000:02:02.0: reg 10: [io 0xd800-0xdfff]
[ 0.084536] pci 0000:02:02.0: PME# supported from D3hot D3cold
[ 0.084543] pci 0000:02:02.0: PME# disabled
[ 0.089016] pci 0000:02:02.0: address space collision: [io
0xd800-0xdfff] conflicts with 0000:02:01.0 [io 0xdc00-0xdc1f]
[ 0.101548] pnp 00:05: disabling [io 0x0010-0x001f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101554] pnp 00:05: disabling [io 0x0022-0x003f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101559] pnp 00:05: disabling [io 0x0044-0x005f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101565] pnp 00:05: disabling [io 0x0062-0x0063] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101570] pnp 00:05: disabling [io 0x0065-0x006f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101575] pnp 00:05: disabling [io 0x0072-0x007f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101581] pnp 00:05: disabling [io 0x0080] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101586] pnp 00:05: disabling [io 0x0084-0x0086] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101591] pnp 00:05: disabling [io 0x0088] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101596] pnp 00:05: disabling [io 0x008c-0x008e] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101602] pnp 00:05: disabling [io 0x0090-0x009f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101607] pnp 00:05: disabling [io 0x00a2-0x00bf] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101613] pnp 00:05: disabling [io 0x00e0-0x00ef] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101618] pnp 00:05: disabling [io 0x04d0-0x04d1] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.103643] pnp 00:0b: disabling [io 0x0400-0x047f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.103649] pnp 00:0b: disabling [io 0x0680-0x06ff] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.103656] pnp 00:0b: disabling [io 0x0480-0x04bf] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.142140] pci 0000:02:02.0: BAR 0: assigned [io 0x1000-0x17ff]
[ 0.142146] pci 0000:02:02.0: BAR 0: error updating (0x001001 !=
0x00d801)
[ 0.142151] pci 0000:02:02.0: BAR 0: set to [io 0x1000-0x17ff] (PCI
address [0x1000-0x17ff])
[ 785.498741] pci 0000:02:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
The PCI slot 02:02.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible
fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
=== Finished firmware and bootup diagnostics, next deducing cogent software.
===
Predictive diagnostics for card in bus 02:02.0:
Modem chipset detected on
NAME="Communication controller: Agere Systems Lucent V.92 Data/Fax Modem"
CLASS=0780
PCIDEV=11c1:0620
SUBSYS=11c1:0620
IRQ=18
IDENT=agrsm
For candidate modem in: 02:02.0
0780 Communication controller: Agere Systems Lucent V.92 Data/Fax Modem
Primary device ID: 11c1:0620
Support type needed or chipset: agrsm
The AgereSystems/LSI agrsm code supports compiling of a agrmodem + agrserial
driver pair.
There are a few different chipsets which use this driver pair, but they use
different code resources:
Chipsets KV*
PackageNames (most current as of November 2009)
----------------------------------------------------------------------------
------------------
11c1:048c and 11c1:048f 2.6.29
agrsm048pci-2.1.60_20100108_i386.deb or agrsm048pci-2.1.60_20100108.tar.gz
11c1:0620 2.6.31 agrsm06pci-2.1.80_20100106_i386.deb
or agrsm06pci-2.1.80~20100106.tar.gz !!
11c11040 (on HDA audio cards) 2.6.31 agrsm-11c11040_20091225_i386.deb or
agrsm-11c11040-2.1.80~20091225.tar.bz2 !!
All available at:
http://linmodems.technion.ac.il/packages/ltmodem/11c11040/ ;
Additionally there are;
automation & testing agrsm-tools_0.0.1_all.deb or
agrsm-tools-0.0.1-2.noarch.rpm
General background agrsm_howto.txt
----------------------------------------------------------------------------
--------------------
* KV == latest kernel release with a reported success
!! Latest update with major credit to Nikolay Zhuravlev
But see conflict issue:
http://linmodems.technion.ac.il/bigarch/archive-nineth/msg02753.html
For the 11c11040 chip with kernels 2.6.31 and later a change in a modules
loading settingmay be necessary.
Within the file /etc/modprobe.d/alsa-base.conf (or equivalent for your
Distro), change the phrase:
options snd-hda-intel power_save=10
to:
options snd-hda-intel power_save=0
or the agrsm drivers will not function. For Ubuntu related systems this
can be done with:
$ sudo gedit /etc/modprobe.d/alsa-base.conf
Report from Bjorn Wielens:
Please note- trying to load the modules on a OpenSuSE 11.2 system gives
an error about the module_version symbol. Using:
# modprobe --force agrmodem
# modprobe --force agrserial
is necessary to load the drivers, and does not appear to cause ill effects.
All of the above packages are dkms competent. This means that if your Linux
distros dkms package
is previously installed, if provides for future updates matching forthcoming
kernels.
-------------- end Agere Systems section -------------------
Completed candidate modem analyses.
The base of the UDEV device file system is: /dev/.udev
Versions adequately match for the compiler installed: 4.5.2
and the compiler used in kernel assembly: 4.5.2
Minimal compiling resources appear complete:
make utility - /usr/bin/make
Compiler version 4.5
linuc_headers base folder /lib/modules/2.6.38-16-generic/build
However some compilations and executable functions may need additional
files,
in the FileNames.h (so called kernel "h"eaders) collection installed in
/usr/include/ .
For martian_modem, additional required packages are needed. The also
required headers of package libc6 are commonly installed by default.
Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev
packages, for kernels 2.6.24 and later versions.
In not included on your install CD, search for them at
http://packages.ubuntu.com
or comparable Repository for other Linux distros.
When compiling ALSA drivers, the utility "patch" will also be needed.
If a driver compilation fails, with message including some lack of some
FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include. The
minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev
If an alternate ethernet connection is available,
$ apt-get update
$ apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to
display the needed package list:
Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb
Checking pppd properties:
-rwsr-xr-- 1 root dip 273272 2011-02-04 02:43 /usr/sbin/pppd
In case of an "error 17" "serial loopback" problem, see:
http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
To enable dialout without Root permission do:
$ su - root (not for Ubuntu)
sudo chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
sudo chmod a+x /usr/sbin/pppd
Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
lcp-echo-interval 30
lcp-echo-failure 4
noipx
In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
For guidance on FAX usage, get from
http://linmodems.technion.ac.il/packages/ ; get faxing.tar.gz
It has samples for a modem using port /dev/ttySL0, which must be changed to
match your modem's port.
Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth1
Which can interfere with Browser naviagation.
Don't worry about the following, it is for experts should trouble shooting
be necessary.
==========================================================
Checking for modem support lines:
--------------------------------------
/device/modem symbolic link:
slmodemd created symbolic link /dev/ttySL0:
Within /etc/udev/ files:
Within /etc/modprobe.conf files:
Within any ancient /etc/devfs files:
Within ancient kernel 2.4.n /etc/module.conf files:
--------- end modem support lines --------
Contents of dmesg.txt follows:
CPU0
0: 44 IO-APIC-edge timer
1: 8 IO-APIC-edge i8042
4: 6 IO-APIC-edge
6: 3 IO-APIC-edge floppy
7: 0 IO-APIC-edge parport0
8: 0 IO-APIC-edge rtc0
9: 0 IO-APIC-fasteoi acpi
14: 85632 IO-APIC-edge ata_piix
15: 111 IO-APIC-edge ata_piix
16: 3 IO-APIC-fasteoi uhci_hcd:usb2, nouveau
18: 0 IO-APIC-fasteoi uhci_hcd:usb4
19: 0 IO-APIC-fasteoi uhci_hcd:usb3
20: 14404 IO-APIC-fasteoi eth1
21: 15 IO-APIC-fasteoi firewire_ohci
22: 0 IO-APIC-fasteoi EMU10K1
23: 0 IO-APIC-fasteoi ehci_hcd:usb1
NMI: 0 Non-maskable interrupts
LOC: 116200 Local timer interrupts
SPU: 0 Spurious interrupts
PMI: 0 Performance monitoring interrupts
IWI: 0 IRQ work interrupts
RES: 0 Rescheduling interrupts
CAL: 0 Function call interrupts
TLB: 0 TLB shootdowns
TRM: 0 Thermal event interrupts
THR: 0 Threshold APIC interrupts
MCE: 0 Machine check exceptions
MCP: 3 Machine check polls
ERR: 0
MIS: 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.38-16-generic (buildd@panlong) (gcc version
4.5.2 (Ubuntu/Linaro 4.5.2-8ubuntu4) ) #67-Ubuntu SMP Thu Sep 6 18:00:43 UTC
2012 (Ubuntu 2.6.38-16.67-generic 2.6.38.8)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001ff40000 (usable)
[ 0.000000] BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] NX (Execute Disable) protection: approximated by x86 segment
limits
[ 0.000000] DMI 2.3 present.
[ 0.000000] DMI: Gateway
YORKTOWN /D845PECE , BIOS
RG84510A.15A.0030.P13.0302130929 02/13/2003
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000
(usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000
(usable)
[ 0.000000] last_pfn = 0x1ff40 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-DFFFF uncachable
[ 0.000000] E0000-FFFFF write-back
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FE0000000 write-back
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new
0x7010600070106
[ 0.000000] found SMP MP-table at [c00ff780] ff780
[ 0.000000] initial memory mapped : 0 - 01c00000
[ 0.000000] init_memory_mapping: 0000000000000000-000000001ff40000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 001fc00000 page 2M
[ 0.000000] 001fc00000 - 001ff40000 page 4k
[ 0.000000] kernel direct mapping tables up to 1ff40000 @ 1bfb000-1c00000
[ 0.000000] RAMDISK: 1e9c1000 - 1f5fe000
[ 0.000000] ACPI: RSDP 000f72a0 00014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 1ff40000 0002C (v01 GATEWA N5288 02000313 MSFT
00000097)
[ 0.000000] ACPI: FACP 1ff40200 00081 (v02 GATEWA N5288 02000313 MSFT
00000097)
[ 0.000000] ACPI: DSDT 1ff40370 03FB4 (v01 GATEWA N5288 0000010A MSFT
0100000D)
[ 0.000000] ACPI: FACS 1ff50000 00040
[ 0.000000] ACPI: APIC 1ff40300 00068 (v01 GATEWA N5288 02000313 MSFT
00000097)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 1ff40000
[ 0.000000] low ram: 0 - 1ff40000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0001ff40
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0001ff40
[ 0.000000] On node 0 totalpages: 130767
[ 0.000000] free_area_init_node: node 0, pgdat c1786140, node_mem_map
dfb3f200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 991 pages used for memmap
[ 0.000000] Normal zone: 125793 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI
0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 -
0000000000100000
[ 0.000000] Allocating PCI resources starting at 20000000 (gap:
20000000:e0000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2
nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages/cpu @de400000 s28800 r0 d24448
u2097152
[ 0.000000] pcpu-alloc: s28800 r0 d24448 u2097152 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 129744
[ 0.000000] Kernel command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.38-16-generic
root=UUID=4309498f-faf8-433e-a244-ab21030864d2 ro quiet splash vt.handoff=7
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 2617280 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want
memory cgroups
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 493988k/523520k available (5192k kernel code, 29080k
reserved, 2544k data, 700k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xe0740000 - 0xff7fe000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdff40000 ( 511 MB)
[ 0.000000] .init : 0xc178f000 - 0xc183e000 ( 700 kB)
[ 0.000000] .data : 0xc1512301 - 0xc178e4c0 (2544 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1512301 (5192 kB)
[ 0.000000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0,
CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:512 16
[ 0.000000] CPU 0 irqstacks, hard=de008000 soft=de00a000
[ 0.000000] vt handoff: transparent VT on vt#7
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2399.516 MHz processor.
[ 0.004004] Calibrating delay loop (skipped), value calculated using
timer frequency.. 4799.03 BogoMIPS (lpj=9598064)
[ 0.004013] pid_max: default: 32768 minimum: 301
[ 0.004049] Security Framework initialized
[ 0.004076] AppArmor: AppArmor initialized
[ 0.004080] Yama: becoming mindful.
[ 0.004165] Mount-cache hash table entries: 512
[ 0.004388] Initializing cgroup subsys ns
[ 0.004395] ns_cgroup deprecated: consider using the 'clone_children'
flag without the ns_cgroup.
[ 0.004400] Initializing cgroup subsys cpuacct
[ 0.004408] Initializing cgroup subsys memory
[ 0.004423] Initializing cgroup subsys devices
[ 0.004428] Initializing cgroup subsys freezer
[ 0.004432] Initializing cgroup subsys net_cls
[ 0.004436] Initializing cgroup subsys blkio
[ 0.004493] CPU0: Hyper-Threading is disabled
[ 0.004499] mce: CPU supports 4 MCE banks
[ 0.004514] CPU0: Thermal monitoring enabled (TM1)
[ 0.005344] SMP alternatives: switching to UP code
[ 0.019763] ACPI: Core revision 20110112
[ 0.023074] ftrace: allocating 23661 entries in 47 pages
[ 0.024121] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.024422] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.065929] CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07
[ 0.068003] Performance Events: Netburst events, Netburst P4/Xeon PMU
driver.
[ 0.068003] ... version: 0
[ 0.068003] ... bit width: 40
[ 0.068003] ... generic registers: 18
[ 0.068003] ... value mask: 000000ffffffffff
[ 0.068003] ... max period: 0000007fffffffff
[ 0.068003] ... fixed-purpose events: 0
[ 0.068003] ... event mask: 000000000003ffff
[ 0.068003] Brought up 1 CPUs
[ 0.068003] Total of 1 processors activated (4799.03 BogoMIPS).
[ 0.068003] devtmpfs: initialized
[ 0.068003] print_constraints: dummy:
[ 0.068003] Time: 0:34:48 Date: 11/03/12
[ 0.068003] NET: Registered protocol family 16
[ 0.068003] EISA bus registered
[ 0.068003] ACPI: bus type pci registered
[ 0.068003] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
[ 0.068003] PCI: Using configuration type 1 for base access
[ 0.069792] bio: create slab <bio-0> at 0
[ 0.070991] ACPI: EC: Look up EC in DSDT
[ 0.072306] ACPI: Executed 2 blocks of module-level executable AML code
[ 0.075359] ACPI: Interpreter enabled
[ 0.075373] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.075408] ACPI: Using IOAPIC for interrupt routing
[ 0.078033] ACPI: Power Resource [URP1] (off)
[ 0.078099] ACPI: Power Resource [FDDP] (off)
[ 0.078169] ACPI: Power Resource [LPTP] (off)
[ 0.082501] ACPI: No dock devices found.
[ 0.082505] HEST: Table not found.
[ 0.082513] PCI: Ignoring host bridge windows from ACPI; if necessary,
use "pci=use_crs" and report a bug
[ 0.082615] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.082832] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
(ignored)
[ 0.082838] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
(ignored)
[ 0.082842] pci_root PNP0A03:00: host bridge window [mem
0x000a0000-0x000bffff] (ignored)
[ 0.082847] pci_root PNP0A03:00: host bridge window [mem
0x20000000-0xffffffff] (ignored)
[ 0.082869] pci 0000:00:00.0: [8086:2560] type 0 class 0x000600
[ 0.083055] pci 0000:00:00.0: reg 10: [mem 0xf8000000-0xfbffffff pref]
[ 0.083128] pci 0000:00:01.0: [8086:2561] type 1 class 0x000604
[ 0.083205] pci 0000:00:1d.0: [8086:24c2] type 0 class 0x000c03
[ 0.083255] pci 0000:00:1d.0: reg 20: [io 0xe800-0xe81f]
[ 0.083294] pci 0000:00:1d.1: [8086:24c4] type 0 class 0x000c03
[ 0.083344] pci 0000:00:1d.1: reg 20: [io 0xe880-0xe89f]
[ 0.083382] pci 0000:00:1d.2: [8086:24c7] type 0 class 0x000c03
[ 0.083432] pci 0000:00:1d.2: reg 20: [io 0xec00-0xec1f]
[ 0.083484] pci 0000:00:1d.7: [8086:24cd] type 0 class 0x000c03
[ 0.083510] pci 0000:00:1d.7: reg 10: [mem 0xfebffc00-0xfebfffff]
[ 0.083599] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.083606] pci 0000:00:1d.7: PME# disabled
[ 0.083628] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[ 0.083679] pci 0000:00:1f.0: [8086:24c0] type 0 class 0x000601
[ 0.083684] * The chipset may have PM-Timer Bug. Due to workarounds for a
bug,
[ 0.083687] * this clock source is slow. If you are sure your timer does
not have
[ 0.083690] * this bug, please use "acpi_pm_good" to disable the
workaround
[ 0.083778] pci 0000:00:1f.1: [8086:24cb] type 0 class 0x000101
[ 0.083795] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
[ 0.083807] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
[ 0.083819] pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
[ 0.083831] pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
[ 0.083843] pci 0000:00:1f.1: reg 20: [io 0xffa0-0xffaf]
[ 0.083856] pci 0000:00:1f.1: reg 24: [mem 0x00000000-0x000003ff]
[ 0.083891] pci 0000:00:1f.3: [8086:24c3] type 0 class 0x000c05
[ 0.083942] pci 0000:00:1f.3: reg 20: [io 0xe480-0xe49f]
[ 0.084018] pci 0000:01:00.0: [10de:0171] type 0 class 0x000300
[ 0.084037] pci 0000:01:00.0: reg 10: [mem 0xfd000000-0xfdffffff]
[ 0.084048] pci 0000:01:00.0: reg 14: [mem 0xe8000000-0xefffffff pref]
[ 0.084058] pci 0000:01:00.0: reg 18: [mem 0xf4680000-0xf46fffff pref]
[ 0.084086] pci 0000:01:00.0: reg 30: [mem 0xfe9e0000-0xfe9fffff pref]
[ 0.084144] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.084151] pci 0000:00:01.0: bridge window [io 0xf000-0x0000]
(disabled)
[ 0.084157] pci 0000:00:01.0: bridge window [mem 0xfc900000-0xfe9fffff]
[ 0.084163] pci 0000:00:01.0: bridge window [mem 0xe4500000-0xf46fffff
pref]
[ 0.084193] pci 0000:02:01.0: [1102:0004] type 0 class 0x000401
[ 0.084214] pci 0000:02:01.0: reg 10: [io 0xdc00-0xdc1f]
[ 0.084281] pci 0000:02:01.0: supports D1 D2
[ 0.084305] pci 0000:02:01.2: [1102:4001] type 0 class 0x000c00
[ 0.084326] pci 0000:02:01.2: reg 10: [mem 0xfeaff800-0xfeafffff]
[ 0.084340] pci 0000:02:01.2: reg 14: [mem 0xfeaf8000-0xfeafbfff]
[ 0.084402] pci 0000:02:01.2: supports D1 D2
[ 0.084406] pci 0000:02:01.2: PME# supported from D0 D1 D2 D3hot
[ 0.084412] pci 0000:02:01.2: PME# disabled
[ 0.084446] pci 0000:02:02.0: [11c1:0620] type 0 class 0x000780
[ 0.084467] pci 0000:02:02.0: reg 10: [io 0xd800-0xdfff]
[ 0.084536] pci 0000:02:02.0: PME# supported from D3hot D3cold
[ 0.084543] pci 0000:02:02.0: PME# disabled
[ 0.084570] pci 0000:02:08.0: [8086:1039] type 0 class 0x000200
[ 0.084590] pci 0000:02:08.0: reg 10: [mem 0xfeafe000-0xfeafefff]
[ 0.084602] pci 0000:02:08.0: reg 14: [io 0xd480-0xd4bf]
[ 0.084660] pci 0000:02:08.0: supports D1 D2
[ 0.084664] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.084670] pci 0000:02:08.0: PME# disabled
[ 0.084707] pci 0000:00:1e.0: PCI bridge to [bus 02-02] (subtractive
decode)
[ 0.084715] pci 0000:00:1e.0: bridge window [io 0xd000-0xdfff]
[ 0.084721] pci 0000:00:1e.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.084728] pci 0000:00:1e.0: bridge window [mem 0xf4700000-0xf47fffff
pref]
[ 0.084732] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff]
(subtractive decode)
[ 0.084736] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff]
(subtractive decode)
[ 0.084752] pci_bus 0000:00: on NUMA node 0
[ 0.084758] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.084878] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.087293] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12
14 15)
[ 0.087395] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12
14 15)
[ 0.087493] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12
14 15)
[ 0.087590] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12
14 15)
[ 0.087689] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12
14 15)
[ 0.087787] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12
14 15)
[ 0.087885] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12
14 15)
[ 0.087984] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12
14 15)
[ 0.088197] vgaarb: device added:
PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.088204] vgaarb: loaded
[ 0.088542] SCSI subsystem initialized
[ 0.088643] libata version 3.00 loaded.
[ 0.088726] usbcore: registered new interface driver usbfs
[ 0.088744] usbcore: registered new interface driver hub
[ 0.088790] usbcore: registered new device driver usb
[ 0.088961] wmi: Mapper loaded
[ 0.088965] PCI: Using ACPI for IRQ routing
[ 0.088971] PCI: pci_cache_line_size set to 64 bytes
[ 0.089016] pci 0000:02:02.0: address space collision: [io
0xd800-0xdfff] conflicts with 0000:02:01.0 [io 0xdc00-0xdc1f]
[ 0.089052] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.089056] reserve RAM buffer: 000000001ff40000 - 000000001fffffff
[ 0.089219] NetLabel: Initializing
[ 0.089223] NetLabel: domain hash size = 128
[ 0.089225] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.089242] NetLabel: unlabeled traffic allowed by default
[ 0.100771] AppArmor: AppArmor Filesystem Enabled
[ 0.100828] pnp: PnP ACPI init
[ 0.100861] ACPI: bus type pnp registered
[ 0.101027] pnp 00:00: [bus 00-ff]
[ 0.101032] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.101036] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.101040] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.101044] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.101048] pnp 00:00: [mem 0x00000000 window]
[ 0.101052] pnp 00:00: [mem 0x20000000-0xffffffff window]
[ 0.101134] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.101166] pnp 00:01: [dma 4]
[ 0.101170] pnp 00:01: [io 0x0000-0x000f]
[ 0.101174] pnp 00:01: [io 0x0081-0x0083]
[ 0.101177] pnp 00:01: [io 0x0087]
[ 0.101180] pnp 00:01: [io 0x0089-0x008b]
[ 0.101183] pnp 00:01: [io 0x008f]
[ 0.101186] pnp 00:01: [io 0x00c0-0x00df]
[ 0.101229] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.101248] pnp 00:02: [io 0x0070-0x0071]
[ 0.101269] pnp 00:02: [irq 8]
[ 0.101307] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.101323] pnp 00:03: [io 0x0061]
[ 0.101365] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.101386] pnp 00:04: [io 0x00f0-0x00ff]
[ 0.101394] pnp 00:04: [irq 13]
[ 0.101433] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.101468] pnp 00:05: [io 0x0010-0x001f]
[ 0.101472] pnp 00:05: [io 0x0022-0x003f]
[ 0.101475] pnp 00:05: [io 0x0044-0x005f]
[ 0.101479] pnp 00:05: [io 0x0062-0x0063]
[ 0.101482] pnp 00:05: [io 0x0065-0x006f]
[ 0.101485] pnp 00:05: [io 0x0072-0x007f]
[ 0.101488] pnp 00:05: [io 0x0080]
[ 0.101491] pnp 00:05: [io 0x0084-0x0086]
[ 0.101494] pnp 00:05: [io 0x0088]
[ 0.101497] pnp 00:05: [io 0x008c-0x008e]
[ 0.101500] pnp 00:05: [io 0x0090-0x009f]
[ 0.101504] pnp 00:05: [io 0x00a2-0x00bf]
[ 0.101507] pnp 00:05: [io 0x00e0-0x00ef]
[ 0.101510] pnp 00:05: [io 0x04d0-0x04d1]
[ 0.101548] pnp 00:05: disabling [io 0x0010-0x001f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101554] pnp 00:05: disabling [io 0x0022-0x003f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101559] pnp 00:05: disabling [io 0x0044-0x005f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101565] pnp 00:05: disabling [io 0x0062-0x0063] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101570] pnp 00:05: disabling [io 0x0065-0x006f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101575] pnp 00:05: disabling [io 0x0072-0x007f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101581] pnp 00:05: disabling [io 0x0080] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101586] pnp 00:05: disabling [io 0x0084-0x0086] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101591] pnp 00:05: disabling [io 0x0088] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101596] pnp 00:05: disabling [io 0x008c-0x008e] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101602] pnp 00:05: disabling [io 0x0090-0x009f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101607] pnp 00:05: disabling [io 0x00a2-0x00bf] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101613] pnp 00:05: disabling [io 0x00e0-0x00ef] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101618] pnp 00:05: disabling [io 0x04d0-0x04d1] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.101667] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.101759] pnp 00:06: [mem 0xffb80000-0xffbfffff]
[ 0.101763] pnp 00:06: [mem 0xfff80000-0xffffffff]
[ 0.101807] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.101937] pnp 00:07: [io 0x03f0-0x03f1]
[ 0.101941] pnp 00:07: [io 0x03f2-0x03f3]
[ 0.101945] pnp 00:07: [io 0x03f4-0x03f5]
[ 0.101948] pnp 00:07: [io 0x03f7]
[ 0.101956] pnp 00:07: [irq 6]
[ 0.101959] pnp 00:07: [dma 2]
[ 0.102039] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.102319] pnp 00:08: [io 0x03f8-0x03ff]
[ 0.102328] pnp 00:08: [irq 4]
[ 0.102423] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.102889] pnp 00:09: [io 0x0378-0x037f]
[ 0.102893] pnp 00:09: [io 0x0778-0x077f]
[ 0.102900] pnp 00:09: [irq 7]
[ 0.102903] pnp 00:09: [dma 3]
[ 0.103042] pnp 00:09: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.103091] pnp 00:0a: [io 0x0060]
[ 0.103095] pnp 00:0a: [io 0x0064]
[ 0.103102] pnp 00:0a: [irq 1]
[ 0.103154] pnp 00:0a: Plug and Play ACPI device, IDs PNP0303 PNP030b
(active)
[ 0.103599] pnp 00:0b: [io 0x0400-0x047f]
[ 0.103605] pnp 00:0b: [io 0x0000-0xffffffff disabled]
[ 0.103608] pnp 00:0b: [io 0x0680-0x06ff]
[ 0.103612] pnp 00:0b: [io 0x0480-0x04bf]
[ 0.103615] pnp 00:0b: [mem 0xfec00000-0xfec00fff]
[ 0.103619] pnp 00:0b: [mem 0xfee00000-0xfee00fff]
[ 0.103643] pnp 00:0b: disabling [io 0x0400-0x047f] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.103649] pnp 00:0b: disabling [io 0x0680-0x06ff] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.103656] pnp 00:0b: disabling [io 0x0480-0x04bf] because it overlaps
0000:02:02.0 BAR 0 [io 0x0000-0x07ff]
[ 0.103713] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be
reserved
[ 0.103719] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.103726] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.104081] pnp 00:0c: [mem 0x00000000-0x0009ffff]
[ 0.104085] pnp 00:0c: [mem 0x000c0000-0x000dffff]
[ 0.104089] pnp 00:0c: [mem 0x000e0000-0x000fffff]
[ 0.104093] pnp 00:0c: [mem 0x00100000-0x1fffffff]
[ 0.104096] pnp 00:0c: [mem 0x00000000-0xffffffff disabled]
[ 0.104175] system 00:0c: [mem 0x00000000-0x0009ffff] could not be
reserved
[ 0.104180] system 00:0c: [mem 0x000c0000-0x000dffff] could not be
reserved
[ 0.104186] system 00:0c: [mem 0x000e0000-0x000fffff] could not be
reserved
[ 0.104191] system 00:0c: [mem 0x00100000-0x1fffffff] could not be
reserved
[ 0.104196] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.104476] pnp: PnP ACPI: found 13 devices
[ 0.104480] ACPI: ACPI bus type pnp unregistered
[ 0.104487] PnPBIOS: Disabled by ACPI PNP
[ 0.142038] Switching to clocksource acpi_pm
[ 0.142095] pci 0000:00:1f.1: BAR 5: assigned [mem 0x20000000-0x200003ff]
[ 0.142105] pci 0000:00:1f.1: BAR 5: set to [mem 0x20000000-0x200003ff]
(PCI address [0x20000000-0x200003ff])
[ 0.142111] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.142114] pci 0000:00:01.0: bridge window [io disabled]
[ 0.142121] pci 0000:00:01.0: bridge window [mem 0xfc900000-0xfe9fffff]
[ 0.142128] pci 0000:00:01.0: bridge window [mem 0xe4500000-0xf46fffff
pref]
[ 0.142140] pci 0000:02:02.0: BAR 0: assigned [io 0x1000-0x17ff]
[ 0.142146] pci 0000:02:02.0: BAR 0: error updating (0x001001 !=
0x00d801)
[ 0.142151] pci 0000:02:02.0: BAR 0: set to [io 0x1000-0x17ff] (PCI
address [0x1000-0x17ff])
[ 0.142156] pci 0000:00:1e.0: PCI bridge to [bus 02-02]
[ 0.142161] pci 0000:00:1e.0: bridge window [io 0xd000-0xdfff]
[ 0.142168] pci 0000:00:1e.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.142175] pci 0000:00:1e.0: bridge window [mem 0xf4700000-0xf47fffff
pref]
[ 0.142198] pci 0000:00:1e.0: setting latency timer to 64
[ 0.142204] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.142208] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.142212] pci_bus 0000:01: resource 1 [mem 0xfc900000-0xfe9fffff]
[ 0.142217] pci_bus 0000:01: resource 2 [mem 0xe4500000-0xf46fffff pref]
[ 0.142221] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
[ 0.142225] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.142229] pci_bus 0000:02: resource 2 [mem 0xf4700000-0xf47fffff pref]
[ 0.142234] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
[ 0.142238] pci_bus 0000:02: resource 5 [mem 0x00000000-0xffffffff]
[ 0.142300] NET: Registered protocol family 2
[ 0.142398] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.142681] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.142797] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.142902] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.142905] TCP reno registered
[ 0.142909] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.142919] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.143030] NET: Registered protocol family 1
[ 0.143156] pci 0000:01:00.0: Boot video device
[ 0.143179] pci 0000:02:08.0: Firmware left e100 interrupts enabled;
disabling
[ 0.143189] PCI: CLS 32 bytes, default 64
[ 0.143507] cpufreq-nforce2: No nForce2 chipset.
[ 0.143718] audit: initializing netlink socket (disabled)
[ 0.143736] type=2000 audit(1351902888.140:1): initialized
[ 0.143736] Switched to NOHz mode on CPU #0
[ 0.152847] Trying to unpack rootfs image as initramfs...
[ 0.168437] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.176355] VFS: Disk quotas dquot_6.5.2
[ 0.176471] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.177624] fuse init (API version 7.16)
[ 0.177773] msgmni has been set to 964
[ 0.184425] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.184475] io scheduler noop registered
[ 0.184479] io scheduler deadline registered
[ 0.184505] io scheduler cfq registered (default)
[ 0.184722] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.184761] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.185002] input: Sleep Button as
/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0
[ 0.185017] ACPI: Sleep Button [SLPB]
[ 0.185089] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.185095] ACPI: Power Button [PWRF]
[ 0.185225] ACPI: acpi_idle registered with cpuidle
[ 0.187119] ERST: Table is not found!
[ 0.187258] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.207675] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.212203] isapnp: Scanning for PnP cards...
[ 0.302264] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.324686] Linux agpgart interface v0.103
[ 0.324815] agpgart-intel 0000:00:00.0: Intel 845G Chipset
[ 0.327938] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[ 0.334311] brd: module loaded
[ 0.335206] loop: module loaded
[ 0.335403] i2c-core: driver [adp5520] using legacy suspend method
[ 0.335407] i2c-core: driver [adp5520] using legacy resume method
[ 0.335583] ata_piix 0000:00:1f.1: version 2.13
[ 0.335604] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[ 0.335633] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) ->
IRQ 18
[ 0.335707] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.384396] scsi0 : ata_piix
[ 0.384641] scsi1 : ata_piix
[ 0.387259] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq
14
[ 0.387265] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq
15
[ 0.387914] Fixed MDIO Bus: probed
[ 0.387980] PPP generic driver version 2.4.2
[ 0.388136] tun: Universal TUN/TAP device driver, 1.6
[ 0.388140] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
[ 0.388283] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.388333] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) ->
IRQ 23
[ 0.388358] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.388364] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.388438] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus
number 1
[ 0.388486] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.392365] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.396279] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebffc00
[ 0.416195] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.416465] hub 1-0:1.0: USB hub found
[ 0.416473] hub 1-0:1.0: 6 ports detected
[ 0.416599] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.416624] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.416717] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) ->
IRQ 16
[ 0.416731] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.416737] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.416810] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
number 2
[ 0.416858] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e800
[ 0.417052] hub 2-0:1.0: USB hub found
[ 0.417060] hub 2-0:1.0: 2 ports detected
[ 0.417162] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) ->
IRQ 19
[ 0.417173] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.417177] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.417238] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus
number 3
[ 0.417278] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e880
[ 0.417467] hub 3-0:1.0: USB hub found
[ 0.417474] hub 3-0:1.0: 2 ports detected
[ 0.417562] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) ->
IRQ 18
[ 0.417573] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.417577] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.417637] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus
number 4
[ 0.417674] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ec00
[ 0.417858] hub 4-0:1.0: USB hub found
[ 0.417865] hub 4-0:1.0: 2 ports detected
[ 0.418049] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.418053] i8042: PNP: PS/2 appears to have AUX port disabled, if this
is incorrect please boot with i8042.nopnp
[ 0.418881] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.419081] mousedev: PS/2 mouse device common for all mice
[ 0.422542] rtc_cmos 00:02: RTC can wake from S4
[ 0.422627] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.422657] rtc0: alarms up to one month, 114 bytes nvram
[ 0.422815] device-mapper: uevent: version 1.0.3
[ 0.422943] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised:
dm-devel@xxxxxxxxxx
[ 0.423521] device-mapper: multipath: version 1.2.0 loaded
[ 0.423527] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.423672] EISA: Probing bus 0 at eisa.0
[ 0.423683] Cannot allocate resource for EISA slot 1
[ 0.423713] EISA: Detected 0 cards.
[ 0.428297] cpuidle: using governor ladder
[ 0.428303] cpuidle: using governor menu
[ 0.428755] TCP cubic registered
[ 0.428978] NET: Registered protocol family 10
[ 0.429781] NET: Registered protocol family 17
[ 0.429819] Registering the dns_resolver key type
[ 0.429880] Using IPI No-Shortcut mode
[ 0.430069] PM: Hibernation image not present or could not be loaded.
[ 0.430086] registered taskstats version 1
[ 0.430313] Magic number: 4:281:556
[ 0.430385] pci_link PNP0C0F:07: hash matches
[ 0.430442] rtc_cmos 00:02: setting system clock to 2012-11-03 00:34:48
UTC (1351902888)
[ 0.430447] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.430450] EDD information not available.
[ 0.443796] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input2
[ 0.580920] ata2.00: ATAPI: JLMS XJ-HD166S, DGS3, max UDMA/33
[ 0.580930] ata2.01: ATAPI: HL-DT-ST GCE-8481B, GW01, max UDMA/33
[ 0.581350] ata2.00: configured for UDMA/33
[ 0.712699] ata2.01: configured for UDMA/33
[ 0.721399] ata1.00: ATA-5: WDC WD800BB-53CAA1, 17.07W17, max UDMA/100
[ 0.721405] ata1.00: 156301488 sectors, multi 16: LBA
[ 0.721886] ata1.01: ATA-7: Hitachi HDS724040KLAT80, KFABACAA, max
UDMA/133
[ 0.721891] ata1.01: 781422768 sectors, multi 16: LBA48
[ 0.779987] ata1.00: configured for UDMA/100
[ 0.827676] isapnp: No Plug & Play device found
[ 0.876852] ata1.01: configured for UDMA/100
[ 0.877073] scsi 0:0:0:0: Direct-Access ATA WDC WD800BB-53CA
17.0 PQ: 0 ANSI: 5
[ 0.877377] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 0.877559] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0
GB/74.5 GiB)
[ 0.877647] sd 0:0:0:0: [sda] Write Protect is off
[ 0.877652] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.877689] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 0.887053] sda: sda1
[ 0.887346] scsi 0:0:1:0: Direct-Access ATA Hitachi HDS72404
KFAB PQ: 0 ANSI: 5
[ 0.887620] sd 0:0:1:0: Attached scsi generic sg1 type 0
[ 0.887889] sd 0:0:1:0: [sdb] 781422768 512-byte logical blocks: (400
GB/372 GiB)
[ 0.888072] scsi 1:0:0:0: CD-ROM JLMS XJ-HD166S
DGS3 PQ: 0 ANSI: 5
[ 0.888255] sd 0:0:1:0: [sdb] Write Protect is off
[ 0.888261] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 0.888301] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 0.888907] sd 0:0:0:0: [sda] Attached SCSI disk
[ 0.888969] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 0.888974] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 0.889127] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 0.889234] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 0.889772] scsi 1:0:1:0: CD-ROM HL-DT-ST CD-RW GCE-8481B
GW01 PQ: 0 ANSI: 5
[ 0.892381] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 0.892614] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 0.892741] sr 1:0:1:0: Attached scsi generic sg3 type 5
[ 0.901548] sdb: sdb1
[ 0.901977] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 1.017972] Freeing initrd memory: 12532k freed
[ 1.038513] Freeing unused kernel memory: 700k freed
[ 1.039541] Write protecting the kernel text: 5196k
[ 1.039585] Write protecting the kernel read-only data: 2152k
[ 1.078309] <30>udev[64]: starting version 167
[ 1.152090] Refined TSC clocksource calibration: 2399.922 MHz.
[ 1.152102] Switching to clocksource tsc
[ 1.383251] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 1.383257] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.383326] e100 0000:02:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.420063] Floppy drive(s): fd0 is 1.44M
[ 1.442175] e100 0000:02:08.0: PME# disabled
[ 1.442893] e100 0000:02:08.0: eth0: addr 0xfeafe000, irq 20, MAC addr
00:07:e9:ef:33:b0
[ 1.455912] FDC 0 is a post-1991 82077
[ 1.463889] firewire_ohci 0000:02:01.2: PCI INT B -> GSI 21 (level, low)
-> IRQ 21
[ 1.516224] firewire_ohci: Added fw-ohci device 0000:02:01.2, OHCI v1.10,
4 IR + 8 IT contexts, quirks 0x0
[ 2.016195] firewire_core: created device fw0: GUID 00023c005001b2f3,
S400
[ 9.023689] <30>udev[254]: starting version 167
[ 10.387399] intel_rng: Firmware space is locked read-only. If you can't
or
[ 10.387405] intel_rng: don't want to disable this in firmware setup, and
if
[ 10.387407] intel_rng: you are certain that your system has a functional
[ 10.387409] intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 10.469755] parport_pc 00:09: reported by Plug and Play ACPI
[ 10.469820] parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 10.488476] lp: driver loaded but no devices found
[ 10.502085] ppdev: user-space parallel port driver
[ 10.567657] lp0: using parport0 (interrupt-driven).
[ 10.872801] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 11.287839] <30>udev[268]: renamed network interface eth0 to eth1
[ 11.907469] [drm] Initialized drm 1.1.0 20060810
[ 12.132659] type=1400 audit(1351902900.201:2): apparmor="STATUS"
operation="profile_load" name="/sbin/dhclient" pid=465
comm="apparmor_parser"
[ 12.133601] type=1400 audit(1351902900.201:3): apparmor="STATUS"
operation="profile_load"
name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=465
comm="apparmor_parser"
[ 12.134196] type=1400 audit(1351902900.201:4): apparmor="STATUS"
operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script"
pid=465 comm="apparmor_parser"
[ 12.135408] type=1400 audit(1351902900.201:5): apparmor="STATUS"
operation="profile_replace" name="/sbin/dhclient" pid=429
comm="apparmor_parser"
[ 12.136378] type=1400 audit(1351902900.205:6): apparmor="STATUS"
operation="profile_replace"
name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=429
comm="apparmor_parser"
[ 12.136978] type=1400 audit(1351902900.205:7): apparmor="STATUS"
operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script"
pid=429 comm="apparmor_parser"
[ 12.398113] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ
16
[ 12.404675] [drm] nouveau 0000:01:00.0: Detected an NV10 generation card
(0x017100a5)
[ 12.404999] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image
from PRAMIN
[ 12.451673] [drm] nouveau 0000:01:00.0: ... appears to be valid
[ 12.451872] [drm] nouveau 0000:01:00.0: BMP BIOS found
[ 12.451877] [drm] nouveau 0000:01:00.0: BMP version 5.21
[ 12.451881] [drm] nouveau 0000:01:00.0: Bios version 04.17.00.55
[ 12.451886] [drm] nouveau 0000:01:00.0: Found Display Configuration Block
version 2.0
[ 12.451891] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01000100
000088b8
[ 12.451896] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 02010121
00000303
[ 12.451900] [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 02010221
00000303
[ 12.451904] [drm] nouveau 0000:01:00.0: Merging DCB entries 1 and 2
[ 12.452076] [drm] nouveau 0000:01:00.0: Loading NV17 power sequencing
microcode
[ 12.452082] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at
offset 0xCE28
[ 12.452124] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at
offset 0xD16E
[ 12.476022] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at
offset 0xCF43
[ 12.508477] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at
offset 0xD6FD
[ 12.508492] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at
offset 0xD0CA
[ 12.524234] EMU10K1_Audigy 0000:02:01.0: PCI INT A -> GSI 22 (level, low)
-> IRQ 22
[ 12.908513] type=1400 audit(1351902900.977:8): apparmor="STATUS"
operation="profile_load" name="/usr/sbin/ntpd" pid=481
comm="apparmor_parser"
[ 12.909730] type=1400 audit(1351902900.977:9): apparmor="STATUS"
operation="profile_replace" name="/usr/sbin/ntpd" pid=482
comm="apparmor_parser"
[ 13.040056] [drm] nouveau 0000:01:00.0: 0 available performance level(s)
[ 13.040072] [drm] nouveau 0000:01:00.0: c: memory 333MHz core 270MHz
[ 13.040173] [TTM] Zone kernel: Available graphics memory: 253610 kiB.
[ 13.040177] [TTM] Initializing pool allocator.
[ 13.040196] [drm] nouveau 0000:01:00.0: Detected 128MiB VRAM
[ 13.040483] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
[ 13.040507] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x
mode
[ 13.040542] nouveau 0000:01:00.0: putting AGP V2 device into 4x mode
[ 13.040570] [drm] nouveau 0000:01:00.0: 64 MiB GART (aperture)
[ 13.040618] [drm] nouveau 0000:01:00.0: Saving VGA fonts
[ 13.089466] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 13.089471] [drm] No driver support for vblank timestamp query.
[ 13.091140] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga
encoder (output 0)
[ 13.091148] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV encoder
(output 1)
[ 13.245206] [drm] nouveau 0000:01:00.0: allocated 1280x1024 fb: 0x49000,
bo dd654a00
[ 13.245592] fbcon: nouveaufb (fb0) is primary device
[ 13.247581] Console: switching to colour frame buffer device 160x64
[ 13.247626] fb0: nouveaufb frame buffer device
[ 13.247629] drm: registered panic notifier
[ 13.249450] [drm] Initialized nouveau 0.0.16 20090420 for 0000:01:00.0 on
minor 0
[ 14.062391] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.211179] nf_conntrack version 0.5.0 (7925 buckets, 31700 max)
[ 15.513678] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 15.516161] e100 0000:02:08.0: eth1: NIC Link is Up 100 Mbps Full Duplex
[ 15.516281] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 15.890957] Adding 1048572k swap on /mnt/1024Mb.swap. Priority:-1
extents:289 across:1071652k
[ 15.928854] EXT3-fs: barriers not enabled
[ 15.955228] kjournald starting. Commit interval 5 seconds
[ 15.956140] EXT3-fs (sdb1): using internal journal
[ 15.956148] EXT3-fs (sdb1): mounted filesystem with ordered data mode
[ 18.050475] type=1400 audit(1351902906.117:10): apparmor="STATUS"
operation="profile_replace" name="/sbin/dhclient" pid=762
comm="apparmor_parser"
[ 18.062642] type=1400 audit(1351902906.129:11): apparmor="STATUS"
operation="profile_replace"
name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=762
comm="apparmor_parser"
[ 18.063241] type=1400 audit(1351902906.129:12): apparmor="STATUS"
operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script"
pid=762 comm="apparmor_parser"
[ 18.198868] type=1400 audit(1351902906.265:13): apparmor="STATUS"
operation="profile_load" name="/usr/bin/freshclam" pid=764
comm="apparmor_parser"
[ 19.180133] type=1400 audit(1351902907.249:14): apparmor="STATUS"
operation="profile_load" name="/usr/sbin/mysqld" pid=772
comm="apparmor_parser"
[ 19.184856] type=1400 audit(1351902907.253:15): apparmor="STATUS"
operation="profile_replace" name="/usr/sbin/ntpd" pid=781
comm="apparmor_parser"
[ 19.327657] type=1400 audit(1351902907.393:16): apparmor="STATUS"
operation="profile_load" name="/usr/sbin/tcpdump" pid=782
comm="apparmor_parser"
[ 21.208874] type=1400 audit(1351902909.277:17): apparmor="STATUS"
operation="profile_replace" name="/usr/sbin/mysqld" pid=921
comm="apparmor_parser"
[ 25.936016] eth1: no IPv6 routers present
[ 111.119831] Inbound IN=eth1 OUT=
MAC=ff:ff:ff:ff:ff:ff:00:19:1d:f6:13:96:08:00 SRC=0.0.0.0
DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=64 ID=62838 PROTO=UDP
SPT=68 DPT=67 LEN=308
[ 230.883128] Inbound IN=eth1 OUT=
MAC=ff:ff:ff:ff:ff:ff:00:19:1d:f6:13:96:08:00 SRC=0.0.0.0
DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=64 ID=62929 PROTO=UDP
SPT=68 DPT=67 LEN=308
[ 271.461111] Inbound IN=eth1 OUT=
MAC=ff:ff:ff:ff:ff:ff:f0:7b:cb:83:52:46:08:00 SRC=0.0.0.0
DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=128 ID=30189 PROTO=UDP
SPT=68 DPT=67 LEN=308
[ 318.974878] Inbound IN=eth1 OUT=
MAC=ff:ff:ff:ff:ff:ff:f0:7b:cb:83:52:46:08:00 SRC=0.0.0.0
DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=128 ID=31328 PROTO=UDP
SPT=68 DPT=67 LEN=308
[ 350.944161] Inbound IN=eth1 OUT=
MAC=ff:ff:ff:ff:ff:ff:00:19:1d:f6:13:96:08:00 SRC=0.0.0.0
DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=64 ID=63036 PROTO=UDP
SPT=68 DPT=67 LEN=308
[ 484.345180] Inbound IN=eth1 OUT=
MAC=ff:ff:ff:ff:ff:ff:00:1d:fe:eb:0c:80:08:00 SRC=0.0.0.0
DST=255.255.255.255 LEN=328 TOS=0x10 PREC=0x00 TTL=16 ID=0 PROTO=UDP SPT=68
DPT=67 LEN=308
[ 785.392247] agrmodem: module license 'Proprietary' taints kernel.
[ 785.392254] Disabling lock debugging due to kernel taint
[ 785.451178] * Hello Agere Driver PCIe **
[ 785.498741] pci 0000:02:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 785.498751] get irq 12
[ 785.534335] Loading module Agere Modem Controller driver version
2.1.80-Red Flag NE 5.0 (2007-10-1)
[ 794.584234] ttyAGS3 at I/O 0xd800 (irq = 18) is a AgereModem
[ 794.585847] Loading module Agere Modem Interface driver version
2.1.80.0Red Flag 5.0 NE (2007-10-01)
[ 830.802048] Inbound IN=eth1 OUT=
MAC=ff:ff:ff:ff:ff:ff:00:19:1d:f6:13:96:08:00 SRC=0.0.0.0
DST=255.255.255.255 LEN=328 TOS=0x00 PREC=0x00 TTL=64 ID=63041 PROTO=UDP
SPT=68 DPT=67 LEN=308
Module Size Used by
agrserial 17771 0
agrmodem 1335393 1
ipt_REJECT 12512 5
ipt_LOG 12784 8
xt_state 12514 6
xt_limit 12541 8
iptable_filter 12706 1
iptable_mangle 12615 0
ipt_REDIRECT 12493 1
xt_tcpudp 12531 21
iptable_nat 12977 1
nf_nat 24827 2 ipt_REDIRECT,iptable_nat
nf_conntrack_ipv4 19024 9 iptable_nat,nf_nat
nf_conntrack 69744 4
xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4 12649 1 nf_conntrack_ipv4
ip_tables 18125 3 iptable_filter,iptable_mangle,iptable_nat
x_tables 21907 10
ipt_REJECT,ipt_LOG,xt_state,xt_limit,iptable_filter,iptable_mangle,ipt_REDIR
ECT,xt_tcpudp,iptable_nat,ip_tables
snd_emu10k1 137068 0
nouveau 621925 1
ttm 65184 1 nouveau
snd_rawmidi 25269 1 snd_emu10k1
drm_kms_helper 40971 1 nouveau
snd_ac97_codec 105614 1 snd_emu10k1
drm 184164 3 nouveau,ttm,drm_kms_helper
ac97_bus 12642 1 snd_ac97_codec
snd_pcm 80042 2 snd_emu10k1,snd_ac97_codec
snd_seq_device 14110 2 snd_emu10k1,snd_rawmidi
i2c_algo_bit 13184 1 nouveau
snd_timer 28659 2 snd_emu10k1,snd_pcm
snd_page_alloc 14073 2 snd_emu10k1,snd_pcm
snd_util_mem 13786 1 snd_emu10k1
snd_hwdep 13274 1 snd_emu10k1
snd 55295 8
agrmodem,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_seq_device,snd_t
imer,snd_hwdep
soundcore 12600 1 snd
video 19112 1 nouveau
shpchp 32345 0
ppdev 12849 0
lp 13349 0
parport_pc 32111 1
parport 36746 3 ppdev,lp,parport_pc
firewire_ohci 31504 0
firewire_core 56138 1 firewire_ohci
floppy 60032 0
e100 40108 0
crc_itu_t 12627 1 firewire_core
