Sebastian, A minimal test of your modem hardware is simple: # wvdialconf which should find and report capabilities of the modem. Actual dialouts require an account with an Internet Provider. Otherwise you are in the domain of Asterisk and should study its documentation. To the best of my knowledge, none of us use it. But per my <<< below you modem should be capable. MarvS =============== Asterisk is an Open Source PBX and telephony toolkit. It is, in a sense, middleware between Internet and telephony channels on the bottom, and Internet and telephony applications at the top. . Asterisk can be used with Voice over IP (SIP, H.323, IAX and more) standards, or the Public Switched Telephone Network (PSTN) through supported hardware. . Supported hardware: . * All Wildcard (tm) ISDN PRI cards from Digium (http://www.digium.com) * HFC-S/HFC-4S-based ISDN BRI cards (Junghanns.NET, beroNet, Digium etc.) * All TDM (FXO/FXS) cards from Digium * Various clones of Digium cards such as those by OpenVox * Xorcom Astribank USB telephony adapter (http://www.xorcom.com) * Voicetronix OpenPCI, OpenLine and OpenSwitch cards * CAPI-compatible ISDN cards (using the add-on package chan-capi) * Full Duplex Sound Card (ALSA or OSS) supported by Linux <<<< * Tormenta T1/E1 card (http://www.zapatatelephony.org) * QuickNet Internet PhoneJack and LineJack (http://www.quicknet.net) On Fri, Jan 20, 2012 at 5:50 AM, Sebastian Tarach <starach@xxxxxxxxx> wrote: > Thanks I have installed sl-modem-daemon and it created /dev/ttySL0 for > me. I probably should have mentioned this earlier but I want to use it > to learn how to configure and use Asterisk. But before that I would > like to verify that everything works. How can I make a call retrive > some information from the device or do actually anything? I have tried > to enter some AT commands like > > echo "ATDT <my mobile phone number>" > /dev/ttySL0 > or > modem-cmd /dev/ttySL0 ATD<number> > but it didn't worked at all > > On 19 January 2012 14:37, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> wrote: >> Sebastian >> >> re: Modem: Intel Corporation 82801DB/DBL/DBM " >> PCIDEV=8086:24c6 >> SUBSYS=1179:0001 >> IRQ=4 >> SLMODEMD_DEVICE=modem:1 >> Driver=snd-intel8x0m >> >> All looks OK on your System. Install the package sl-modem-daemon, >> which will initiate your modem on bootup. The default country is the >> USA, so if you are elsewhere >> # gedit /etc/default/sl-modem-daemon >> and change the COUNTRY setting >> >> Thereafter Root/Adm command >> # wvdialconf >> should find the modem and write /etc/wvdial.conf . With >> # gedit /etc/wvdial.conf >> edit in your personal info, while removing the ; < > symbols >> and adding a line: >> Carrier check = no >> and SAVE >> This does not have to be repeated. Read >> # man wvdial >> for details >> >> Starting a dialout requires Root/Adm permission, so: >> # wvdial >> or >> $ sudo wvdial >> >> MarvS >> >> >> >> On Thu, Jan 19, 2012 at 8:11 AM, Sebastian Tarach <starach@xxxxxxxxx> wrote: >>> Hello, >>> >>> I have downloaded the scanModem script and executed but now I have no >>> idea what to do next. File called 1stRead.txt points me to >>> YourModem.txt file which does not exists. I have tried to read >>> ModemData.txt which I have attached to this email but it confuses me >>> and I just don't what to do next. Thanks in advance. >>> >>> Best Regards